Browsing by Author "Plentz, Jonathan"
Now showing 1 - 14 of 14
Results Per Page
Sort Options
- ItemAbsolute EUV reflectivity measurements using a broadband high-harmonic source and an in situ single exposure reference scheme(Washington, DC : Soc., 2022) Abel, Johann J.; Wiesner, Felix; Nathanael, Jan; Reinhard, Julius; Wünsche, Martin; Schmidl, Gabriele; Gawlik, Annett; Hübner, Uwe; Plentz, Jonathan; Rödel, Christian; Paulus, Gerhard G.; Fuchs, SilvioWe present a tabletop setup for extreme ultraviolet (EUV) reflection spectroscopy in the spectral range from 40 to 100 eV by using high-harmonic radiation. The simultaneous measurements of reference and sample spectra with high energy resolution provide precise and robust absolute reflectivity measurements, even when operating with spectrally fluctuating EUV sources. The stability and sensitivity of EUV reflectivity measurements are crucial factors for many applications in attosecond science, EUV spectroscopy, and nano-scale tomography. We show that the accuracy and stability of our in situ referencing scheme are almost one order of magnitude better in comparison to subsequent reference measurements. We demonstrate the performance of the setup by reflective near-edge x-ray absorption fine structure measurements of the aluminum L2/3 absorption edge in α-Al2O3 and compare the results to synchrotron measurements.
- ItemAluminum-Doped Zinc Oxide Improved by Silver Nanowires for Flexible, Semitransparent and Conductive Electrodes on Textile with High Temperature Stability(Basel : MDPI, 2023) Hupfer, Maximilian Lutz; Gawlik, Annett; Dellith, Jan; Plentz, JonathanIn order to facilitate the design freedom for the implementation of textile-integrated electronics, we seek flexible transparent conductive electrodes (TCEs) that can withstand not only the mechanical stresses encountered during use but also the thermal stresses of post-treatment. The transparent conductive oxides (TCO) typically used for this purpose are rigid in comparison to the fibers or textiles they are intended to coat. In this paper, a TCO, specifically aluminum-doped zinc oxide (Al:ZnO), is combined with an underlying layer of silver nanowires (Ag-NW). This combination brings together the advantages of a closed, conductive Al:ZnO layer and a flexible Ag-NW layer, forming a TCE. The result is a transparency of 20–25% (within the 400–800 nm range) and a sheet resistance of 10 Ω/sq that remains almost unchanged, even after post-treatment at 180 °C.
- ItemAmorphous Silicon Thin-Film Solar Cells on Fabrics as Large-Scale Detectors for Textile Personal Protective Equipment in Active Laser Safety †(Basel : MDPI, 2023) Gawlik, Annett; Brückner, Uwe; Schmidl, Gabriele; Wagner, Volker; Paa, Wolfgang; Plentz, JonathanLaser safety is starting to play an increasingly important role, especially when the laser is used as a tool. Passive laser safety systems quickly reach their limits and, in some cases, provide inadequate protection. To counteract this, various active systems have been developed. Flexible and especially textile-protective materials pose a special challenge. The market still lacks personal protective equipment (PPE) for active laser safety. Covering these materials with solar cells as large-area optical detectors offers a promising possibility. In this work, an active laser protection fabric with amorphous silicon solar cells is presented as a large-scale sensor for continuous wave and pulsed lasers (down to ns). First, the fabric and the solar cells were examined separately for irradiation behavior and damage. Laser irradiation was performed at wavelengths of 245, 355, 532, and 808 nm. The solar cell sensors were then applied directly to the laser protection fabric. The damage and destruction behavior of the active laser protection system was investigated. The results show that the basic safety function of the solar cell is still preserved when the locally damaged or destroyed area is irradiated again. A simple automatic shutdown system was used to demonstrate active laser protection within 50 ms.
- ItemBiomimic Vein-Like Transparent Conducting Electrodes with Low Sheet Resistance and Metal Consumption(Berlin ; Heidelberg [u.a.] : Springer, 2020) Jia, Guobin; Plentz, Jonathan; Dellith, Andrea; Schmidt, Christa; Dellith, Jan; Schmidl, Gabriele; Andrä, GudrunAbstract: In this contribution, inspired by the excellent resource management and material transport function of leaf veins, the electrical transport function of metallized leaf veins is mimicked from the material transport function of the vein networks. By electroless copper plating on real leaf vein networks with copper thickness of only several hundred nanometre up to several micrometre, certain leaf veins can be converted to transparent conductive electrodes with an ultralow sheet resistance 100 times lower than that of state-of-the-art indium tin oxide thin films, combined with a broadband optical transmission of above 80% in the UV–VIS–IR range. Additionally, the resource efficiency of the vein-like electrode is characterized by the small amount of material needed to build up the networks and the low copper consumption during metallization. In particular, the high current density transport capability of the electrode of > 6000 A cm−2 was demonstrated. These superior properties of the vein-like structures inspire the design of high-performance transparent conductive electrodes without using critical materials and may significantly reduce the Ag consumption down to < 10% of the current level for mass production of solar cells and will contribute greatly to the electrode for high power density concentrator solar cells, high power density Li-ion batteries, and supercapacitors.[Figure not available: see fulltext.]. © 2020, © 2020, The Author(s).
- ItemCarrier Lifetime in Liquid-phase Crystallized Silicon on Glass(Amsterdam [u.a.] : Elsevier, 2016) Vetter, Michael; Gawlik, Annett; Plentz, Jonathan; Andrä, Gudrun; Ribeyron, Pierre-Jean; Cuevas, Andres; Weeber, Arthur; Ballif, Christophe; Glunz, Stefan; Poortmans, Jef; Brendel, Rolf; Aberle, Armin; Sinton, Ron; Verlinden, Pierre; Hahn, GisoLiquid-phase crystallized silicon on glass (LPCSG) presents a promising material to fabricate high quality silicon thin films, e.g. for solar cells and modules. Barrier layers and a doped amorphous silicon layer are deposited on the glass substrate followed by crystallization with a line focus laser beam. In this paper we introduce injection level dependent lifetime measurements generated by the quasi steady-state photoconductance decay method (QSSPC) to characterize LPCSG absorbers. This contactless method allows a determination of the LPCSG absorber quality already at an early stage of solar cell fabrication, and provides a monitoring of the absorber quality during the solar cell fabrication steps. We found minority carrier lifetimes higher than 200ns in our layers (e.g. n-type absorber with ND=2x1015cm-3) indicating a surface recombination velocity SBL<3000cm/s at the barrier layer/Si interface.
- ItemCombining super-resolution microcopy with neuronal network recording using magnesium fluoride thin films as cover layer for multi-electrode array technology(Berlin : Nature Publishing, 2019) Schmidl, Lars; Schmidl, Gabriele; Gawlik, Annett; Dellith, Jan; Hübner, Uwe; Tympel, Volker; Schmidl, Frank; Plentz, Jonathan; Geis, Christian; Haselmann, HolgerWe present an approach for fabrication of reproducible, chemically and mechanically robust functionalized layers based on MgF2 thin films on thin glass substrates. These show great advantages for use in super-resolution microscopy as well as for multi-electrode-array fabrication and are especially suited for combination of these techniques. The transparency of the coated substrates with the low refractive index material is adjustable by the layer thickness and can be increased above 92%. Due to the hydrophobic and lipophilic properties of the thin crystalline MgF2 layers, the temporal stable adhesion needed for fixation of thin tissue, e.g. cryogenic brain slices is given. This has been tested using localization-based super-resolution microscopy with currently highest spatial resolution in light microscopy. We demonstrated that direct stochastic optical reconstruction microscopy revealed in reliable imaging of structures of central synapses by use of double immunostaining of post- (homer1 and GluA2) and presynaptic (bassoon) marker structure in a 10 µm brain slice without additional fixing of the slices. Due to the proven additional electrical insulating effect of MgF2 layers, surfaces of multi-electrode-arrays were coated with this material and tested by voltage-current-measurements. MgF2 coated multi-electrode-arrays can be used as a functionalized microscope cover slip for combination with live-cell super-resolution microscopy.
- ItemCopper Iodide on Spacer Fabrics as Textile Thermoelectric Device for Energy Generation(Basel : MDPI, 2022) Schmidl, Gabriele; Jia, Guobin; Gawlik, Annett; Lorenz, Philipp; Zieger, Gabriel; Dellith, Jan; Diegel, Marco; Plentz, JonathanThe integration of electronic functionalities into textiles for use as wearable sensors, energy harvesters, or coolers has become increasingly important in recent years. A special focus is on efficient thermoelectric materials. Copper iodide as a p-type thermoelectrically active, nontoxic material is attractive for energy harvesting and energy generation because of its transparency and possible high-power factor. The deposition of CuI on polyester spacer fabrics by wet chemical processes represents a great potential for use in textile industry for example as flexible thermoelectric energy generators in the leisure or industrial sector as well as in medical technologies. The deposited material on polyester yarn is investigated by electron microscopy, x-ray diffraction and by thermoelectric measurements. The Seebeck coefficient was observed between 112 and 153 µV/K in a temperature range between 30 °C and 90 °C. It is demonstrated that the maximum output power reached 99 nW at temperature difference of 65.5 K with respect to room temperature for a single textile element. However, several elements can be connected in series and the output power can be linear upscaled. Thus, CuI coated on 3D spacer fabrics can be attractive to fabricate thermoelectric devices especially in the lower temperature range for textile medical or leisure applications.
- ItemExperimental realization of a 12,000-finesse laser cavity based on a low-noise microstructured mirror(London : Springer Nature, 2023) Dickmann, Johannes; Sauer, Steffen; Meyer, Jan; Gaedtke, Mika; Siefke, Thomas; Brückner, Uwe; Plentz, Jonathan; Kroker, StefanieThe most precise measurement tools of humankind are equipped with ultra-stable lasers. State-of-the-art laser stabilization techniques are based on external cavities, that are limited by noise originated in the coatings of the cavity mirrors. Microstructured mirror coatings (so-called meta-mirrors) are a promising technology to overcome the limitations of coating noise and therewith pave the way towards next-generation ultra-stable lasers. We present experimental realization of a 12,000-finesse optical cavity based on one low-noise meta-mirror. The use of the mirrors studied here in cryogenic silicon cavities represents an order of magnitude reduction in the current limiting mirror noise, such that the stability limit due to fundamental noise can be reduced to 5 × 10−18.
- ItemFabrication of self-assembled spherical Gold Particles by pulsed UV Laser Treatment(Berlin : Nature Publishing, 2018) Schmidl, Gabriele; Jia, Guobin; Gawlik, Annett; Kreusch, Jonathan; Schmidl, Frank; Dellith, Jan; Dathe, André; Lin, Zhan-Hong; Huang, Jer-Shing; Plentz, JonathanWe report on the fabrication of spherical Au spheres by pulsed laser treatment using a KrF excimer laser (248 nm, 25 ns) under ambient conditions as a fast and high throughput fabrication technique. The presented experiments were realized using initial Au layers of 100 nm thickness deposited on optically transparent and low cost Borofloat glass or single-crystalline SrTiO3 substrates, respectively. High (111)-orientation and smoothness (RMS ≈ 1 nm) are the properties of the deposited Au layers before laser treatment. After laser treatment, spheres with size distribution ranging from hundreds of nanometers up to several micrometers were produced. Single-particle scattering spectra with distinct plasmonic resonance peaks are presented to reveal the critical role of optimal irradiation parameters in the process of laser induced particle self-assembly. The variation of irradiation parameters like fluence and number of laser pulses influences the melting, dewetting and solidification process of the Au layers and thus the formation of extremely well shaped spherical particles. The gold layers on Borofloat glass and SrTiO3 are found to show a slightly different behavior under laser treatment. We also discuss the effect of substrates.We report on the fabrication of spherical Au spheres by pulsed laser treatment using a KrF excimer laser (248 nm, 25 ns) under ambient conditions as a fast and high throughput fabrication technique. The presented experiments were realized using initial Au layers of 100 nm thickness deposited on optically transparent and low cost Borofloat glass or single-crystalline SrTiO3 substrates, respectively. High (111)-orientation and smoothness (RMS ≈ 1 nm) are the properties of the deposited Au layers before laser treatment. After laser treatment, spheres with size distribution ranging from hundreds of nanometers up to several micrometers were produced. Single-particle scattering spectra with distinct plasmonic resonance peaks are presented to reveal the critical role of optimal irradiation parameters in the process of laser induced particle self-assembly. The variation of irradiation parameters like fluence and number of laser pulses influences the melting, dewetting and solidification process of the Au layers and thus the formation of extremely well shaped spherical particles. The gold layers on Borofloat glass and SrTiO3 are found to show a slightly different behavior under laser treatment. We also discuss the effect of substrates.
- ItemLarge area graphene deposition on hydrophobic surfaces, flexible textiles, glass fibers, 3D structures, and adhesion of graphene layer(Basel : MDPI, 2019) Jia, Guobin; Plentz, Jonathan; Dellith, Jan; Dellith, Andrea; Wahyuono, Ruri Agung; Andrä, GudrunGraphene and its derivatives have many superior electrical, thermal, mechanical, chemical, and structural properties, and promise for many applications. One of the issues for scalable applications is the lack of a simple, reliable method that allows the deposit of a well-ordered monolayer using low-cost graphene flakes onto target substrates with different surface properties. Another issue is the adhesion of the deposited graphene thin film, which has not been well investigated yet. Following our former finding of a double self-assembly (DSA) process for efficient deposition of a monolayer of graphene flakes (MGFs), in this work we demonstrate that the DSA process can be applied even on very challenging samples including highly hydrophobic polytetrafluoroethylene (PTFE), flexible textiles, complex 3D objects, and thin glass fibers. Additionally, we tested adhesion of the graphene flakes on the flat glass substrate by scotch tape peel test of the MGFs. The results show that the graphene flakes adhere quite well on the flat glass substrate and most of the graphene flakes stay on the glass. These findings may trigger many large-scale applications of low-cost graphene feedstocks and other 2D materials.
- ItemPorous spherical gold nanoparticles via a laser induced process(Cambridge : Royal Society of Chemistry, 2022) Schmidl, Gabriele; Raugust, Marc; Jia, Guobin; Dellith, Andrea; Dellith, Jan; Schmidl, Frank; Plentz, JonathanNanoparticles consisting of a mixture of several metals and also porous nanoparticles due to their special structure exhibit properties that find applications in spectroscopic detection or catalysis. Different approaches of top down or bottom up technologies exist for the fabrication of such particles. We present a novel combined approach for the fabrication of spherical porous gold nanoparticles on low-cost glass substrates under ambient conditions using a UV-laser induced particle preparation process with subsequent wet chemical selective etching. In this preparation route, nanometer-sized branched structures are formed in spherical particles. The laser process, which is applied to a silver/gold bilayer system with different individual layer thicknesses, generates spherical mixed particles in a nanosecond range and influences the properties of the fabricated nanoparticles, such as the size and the mixture and thus the spectral response. The subsequent etching process is performed by selective wet chemical removal of silver from the nanoparticles with diluted nitric acid. The gold to silver ratio was investigated by energy-dispersive X-ray spectroscopy. The porosity depends on laser parameters and film thickness as well as on etching parameters such as time. After etching, the surface area of the remaining Au nanoparticles increases which makes these particles interesting for catalysis and also as carrier particles for substances. Such substances can be positioned at defined locations or be released in appropriate environments. Absorbance spectra are also analyzed to show how the altered fractured shape of the particles changes localized plasmon resonances of the resultingt particles.
- ItemSelf-Assembled Graphene/MWCNT Bilayers as Platinum- Free Counter Electrode in Dye-Sensitized Solar Cells(Weinheim : Wiley-VCH Verl., 2019) Wahyuono, Ruri Agung; Jia, Guobin; Plentz, Jonathan; Dellith, Andrea; Dellith, Jan; Herrmann-Westendorf, Felix; Seyring, Martin; Presselt, Martin; Andrä, Gudrun; Rettenmayr, Markus; Dietzek, BenjaminWe describe the preparation and properties of bilayers of graphene- and multi-walled carbon nanotubes (MWCNTs) as an alternative to conventionally used platinum-based counter electrode for dye-sensitized solar cells (DSSC). The counter electrodes were prepared by a simple and easy-to-implement double self-assembly process. The preparation allows for controlling the surface roughness of electrode in a layer-by-layer deposition. Annealing under N2 atmosphere improves the electrode's conductivity and the catalytic activity of graphene and MWCNTs to reduce the I3 − species within the electrolyte of the DSSC. The performance of different counter-electrodes is compared for ZnO photoanode-based DSSCs. Bilayer electrodes show higher power conversion efficiencies than monolayer graphene electrodes or monolayer MWCNTs electrodes. The bilayer graphene (bottom)/MWCNTs (top) counter electrode-based DSSC exhibits a maximum power conversion efficiency of 4.1 % exceeding the efficiency of a reference DSSC with a thin film platinum counter electrode (efficiency of 3.4 %). In addition, the double self-assembled counter electrodes are mechanically stable, which enables their recycling for DSSCs fabrication without significant loss of the solar cell performance. © 2019 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.
- ItemWafer-level uniformity of atomic-layer-deposited niobium nitride thin films for quantum devices(New York, NY : Inst., 2021) Knehr, Emanuel; Ziegler, Mario; Linzen, Sven; Ilin, Konstantin; Schanz, Patrick; Plentz, Jonathan; Diegel, Marco; Schmidt, Heidemarie; Il’iche, Evgeni; Siegel, MichaelSuperconducting niobium nitride thin films are used for a variety of photon detectors, quantum devices, and superconducting electronics. Most of these applications require highly uniform films, for instance, when moving from single-pixel detectors to arrays with a large active area. Plasma-enhanced atomic layer deposition (ALD) of superconducting niobium nitride is a feasible option to produce high-quality, conformal thin films and has been demonstrated as a film deposition method to fabricate superconducting nanowire single-photon detectors before. Here, we explore the property spread of ALD-NbN across a 6-in. wafer area. Over the equivalent area of a 2-in. wafer, we measure a maximum deviation of 1% in critical temperature and 12% in switching current. Toward larger areas, structural characterizations indicate that changes in the crystal structure seem to be the limiting factor rather than film composition or impurities. The results show that ALD is suited to fabricate NbN thin films as a material for large-area detector arrays and for new detector designs and devices requiring uniform superconducting thin films with precise thickness control.
- ItemZnO nanoflowers-based photoanodes: aqueous chemical synthesis, microstructure and optical properties(Berlin : de Gruyter, 2016) Wahyuono, Ruri Agung; Schmidt, Christa; Dellith, Andrea; Dellith, Jan; Schulz, Martin; Seyring, Martin; Rettenmayr, Markus; Plentz, Jonathan; Dietzek, BenjaminWe have developed an efficient, low temperature, synthetic route for ZnO nanoflowers (NFs) as photoanode material. This alternative route yields small flowerlike nanostructures, built from densely self-assembled tip-ended rod structures. The obtained ZnO NFs possess a large bandgap of 3.27 - 3.39 eV, enabling the generation of an average open current voltage of 0.56 V. Additionally, they show a high internal light harvesting of 14.6•10-7A-mol-1. The growth mechanism and self-assembly of ZnO NFs were studied in detail by joint spectroscopic-TEM investigations. It is shown that the ZnO crystallite size increases with increasing annealing temperatures and that the stress and the improved crystallinity are induced by annealing and reduce the lattice strain and the dislocation density. The bandgaps of ZnO are affected by the lattice strain revealing an optimal region of lattice strain to gain high bandgap energies. The properties of the synthesized ZnO NFs are compared with other morphologies, i.e. ZnO spherical aggregates (SPs) and ZnO nanorods (NRs), and are tested as electrode materials in dye-sensitized solar cells.