Browsing by Author "Togobytska, Nataliya"
Now showing 1 - 5 of 5
Results Per Page
Sort Options
- ItemIdentification of the thermal growth characteristics of coagulated tumor tissue in laser-induced thermotherapy(Berlin : Weierstraß-Institut für Angewandte Analysis und Stochastik, 2011) Hömberg, Dietmar; Liu, Jujun; Togobytska, NataliyaWe consider an inverse problem arising in laser-induced thermotherapy, a minimally invasive method for cancer treatment, in which cancer tissues is destroyed by coagulation. For the dosage planning numerical simulation play an important role. To this end a crucial problem is to identify the thermal growth kinetics of the coagulated zone. Mathematically, this problem is a nonlinear and nonlocal parabolic heat source inverse problem. The solution to this inverse problem is defined as the minimizer of a nonconvex cost functional. The existence of the minimizer is proven. We derive the Gateaux derivative of the cost functional, which is based on the adjoint system, and use it for a numerical approximation of the optimal coefficient.
- ItemNumerical cooling strategy design for hot rolled dual phase steel(Berlin : Weierstraß-Institut für Angewandte Analysis und Stochastik, 2010) Suwanpinij, Piyada; Togobytska, Nataliya; Prahl, Ulrich; Weiss, Wolf; Hömberg, Dietmar; Bleck, WolfgangIn this article, the Mo-Mn dual phase steel and its process parameters in hot rolling are discussed. The process window was derived by combining the experimental work in a hot deformation dilatometer and numerical calculation of process parameters using rate law models for ferrite and martensite transformation. The ferrite formation model is based on the Leblond and Devaux approach while martensite formation is based on the Koistinen-Marburger (K-M) formula. The carbon enrichment during ferrite formation is taken into account for the following martensite formation. After the completion of the parameter identification for the rate law model, the evolution of phases in multiphase steel can be addressed. Particularly, the simulations allow for predicting the preferable degree of retained strain and holding temperature on the run out table (ROT) for the required ferrite fraction.
- ItemOptimal control of a cooling line for production of hot rolled dual phase steel(Berlin : Weierstraß-Institut für Angewandte Analysis und Stochastik, 2013) Bleck, Wolfgang; Hömberg, Dietmar; Prahl, Ulrich; Suwanpinij, Piyada; Togobytska, NataliyaIn this article, the optimal control of a cooling line for production of dual phase steel in a hot rolling process is discussed. In order to achieve a desired dual phase steel microstructure an optimal cooling strategy has to be found. The cooling strategy should be such that a desired final distribution of ferrite in the steel slab is reached most accurately. This problem has been solved by means of mathematical control theory. The results of the optimal control of the cooling line have been verified in hot rolling experiments at the pilot hot rolling mill at the Institute for Metal Forming (IMF), TU Bergakademie Freiberg.
- ItemOptimal control of multiphase steel production(Berlin ; Heidelberg : Springer, 2019) Hömberg, Dietmar; Krumbiegel, Klaus; Togobytska, NataliyaAn optimal control problem for the production of multiphase steel is investigated that takes into account phase transformations in the steel slab. The state equations are a semilinear heat equation coupled with an ordinary differential equation, that describes the evolution of the steel microstructure. The time-dependent heat transfer coefficient serves as a control function. Necessary and sufficient optimality conditions for the control problem are derived. For the numerical solution of the control problem, a reduced sequential quadratic programming method with a primal-dual active set strategy is developed. The numerical results are presented for the optimal control of a cooling line in the production of hot-rolled Mo–Mn dual phase steel. © 2019, The Author(s).
- ItemPhase transformation modeling and parameter identification from dilatometric investigations(Berlin : Weierstraß-Institut für Angewandte Analysis und Stochastik, 2008) Suwanpinij, Piyada; Togobytska, Nataliya; Keul, Christoph; Weiss, Wolf; Prahl, Ulrich; Hömberg, Dietmar; Bleck, WolfgangThe goal of this paper is to propose a new approach towards the evaluation of dilatometric results, which are often employed to analyse the phase transformation kinetics in steel, especially in terms of continuous cooling transformation (CCT) diagram. A simple task of dilatometry is deriving the start and end temperatures of the phase transformation. It can yield phase transformation kinetics provided that plenty metallographic investigations are performed, whose analysis is complicated especially in case of several coexisting product phases. The new method is based on the numerical solution of a thermomechanical identification problem. It is expected that the phase transformation kinetics can be derived by this approach with less metallographic tasks. The first results are remarkably promising although further investigations are required for the numerical simulations.