Browsing by Author "Uhrlandt, D."
Now showing 1 - 14 of 14
Results Per Page
Sort Options
- ItemAdvanced Approach for Radiation Transport Description in 3D Collisional-radiative Models(Praha : Czech Technical University in Prague, Faculty of Electrical Engineering, Department of Physics, 2017) Kalanov, D.; Golubovskii, Y.B.; Uhrlandt, D.; Gortschakow, S.The description of radiation transport phenomena in the frames of collisional-radiative models requires the solution of Holstein-Biberman equation. An advanced solutuion method for 3D plasma obejcts is proposed. The method is applicable for various line contours in a wide range of absorption coefficients. Developed approach is based on discretization of the arbitrary plasma volume on a Cartesian voxel grid. Transport of photons between the cells is computed using the ray traversal algorithm by Amanatides [1]. Solution of the particle balance equations with computed in advance radiative transfer matrix is demonstrated for various typical arc shapes, like e.g. free-burning arc and cylindric arc. Results are compared with corresponding calculations using previously developed approaches. As the method is suited for finite geometries and allows for a strict solution of the radiation transport equation, applicability ranges of previous approximations can be specified.
- ItemAdvanced Nonequilibrium Modelling of DC Tungsten-Inert Gas Arcs(Praha : Czech Technical University in Prague, Faculty of Electrical Engineering, Department of Physics, 2017) Baeva, M.; Uhrlandt, D.The paper is concerned with the state-of-the-art nonequilibrium modelling of a DC tungsten-inert gas arc plasma. The advanced description involves the two-way interaction between the plasma and the electrodes. Results in atmospheric pressure argon demonstrating important features of the arc plasma are presented and discussed. First results in the presence of metal vapour released from the molten anode are presented. Outlook for further developments in nonequilibrium arc modelling are discussed.
- ItemAnalysis of Arc Processes in Multi-chamber Arrester for Lightning Protection at High-voltage Overhead Power Lines(Praha : Czech Technical University in Prague, Faculty of Electrical Engineering, Department of Physics, 2017) Murashov, I.V.; Frolov, V.Y.; Uhrlandt, D.; Gortschakow, S.; Ivanov, D.V.; Sivaev, A.D.Nowadays multi-chamber arresters are widely distributed as devices of lightning protection of overhead power lines. A mathematical modelling of processes in the discharge chamber of multichamber arrester is necessary to carry out in order to improve its breaking capacity. A three-dimensional mathematical transient model of thermal, gas-dynamic and electromagnetic processes taking place in the discharge chamber of multi-chamber arrester is presented in the article. Basic assumptions, model equations, a computational domain and the boundary conditions are described. Plasma turbulence is taken into account. The results of the calculation i.e. distributions of plasma temperature and overpressure in the discharge chamber at different time points are shown. The analysis of the results was carried out. It is shown that the presence of cavities in the electrodes design promotes electric arc extinction in the discharge chamber of multi-chamber arrester.
- ItemAnalysis of C2 SWAN bands in ablation-dominated arcs in CO2 atmosphere(Praha : Czech Technical University in Prague, Faculty of Electrical Engineering, Department of Physics, 2019) Methling, R.; Franke, St.; Götte, N.; Wetzeler, S.; Uhrlandt, D.A model circuit breaker in a high-pressure chamber filled with CO2 atmosphere is used to operate a wall-stabilized arc of several kilo-amperes between tungsten-copper electrodes surrounded by polytetrafluoroethylene nozzles. Optical emission spectroscopy (OES) is carried out via quartz plates inserted into the nozzles using a combination of an imaging spectrometer either with a high-speed video camera or with an ICCD camera. Depending on the nozzle geometry and the current, continuum from C2 Swan bands was detected as absorption as well as emission pattern. After current zero, optical absorption spectroscopy (OAS) using a xenon flashlamp as broadband background radiator was applied. An absorption around 493 nm was detected and attributed to CuF molecules. The study proofs the existence of C2 in the active phase and the formation of CuF near to current zero.
- ItemAnalysis of erosion resistance of CuC arcing contacts manufactured by plasma spraying technology(Praha : Czech Technical University in Prague, Faculty of Electrical Engineering, Department of Physics, 2019) Derevyankin, P.; Frolov, V.; Gonzalez, D.; Gortschakow, S.; Methling, R.; Uhrlandt, D.Results of the erosion resistance study of the CuC electrodes manufactured by plasma spraying technology are presented. The diagnostics has have been performed by means of high-speed camera technique and optical emission spectroscopy which has been synchronised with electrical diagnostics. After the load material analyses, namely determination of mass loss and analysis of micro sections, have been done. It has been found that the erosion rate depends on conditions applied for the formation of coating layer, which was deposited either in air or in argon plasma. Furthermore, the erosion rate is significantly lower in the case of air plasma spraying.
- ItemCathode fall voltage of TIG arcs from a non-equilibrium arc model(Heidelberg : Springer, 2014) Uhrlandt, D.; Baeva, M.; Pipa, A.V.; Kozakov, R.; Gött, G.This work presents modelling results concerning a tungsten inert gas (TIG) welding arc. The model provides a consistent description of the free burning arc, the arc attachment and the electrodes. Thermal and chemical non-equilibrium is considered in the whole arc area, and a detailed model of the cathode space-charge sheath is included. The mechanisms in the cathode pre-sheath are treated in the framework of a non-equilibrium approach which is based on a two-fluid description of electrons and heavy particles and a simplified plasma chemistry of argon. A consistent determination of the electrode fall voltages and temperature distributions is achieved. The model is applied to arcs in pure argon at currents up to 250 A, whereby welding of a workpiece made of mild steel with a fixed burner is considered. Arc voltages in the range from 12 to 17 V are obtained at 50 at 250 A, respectively. The space-charge sheath voltage is found to be about 7 V and almost independent of the current. The corresponding temperatures of the cathode tip are in the range from 3,000 K to about 3,800 K. The results obtained are in a good agreement with measurements.
- ItemA collisional-radiative model of iron vapour in a thermal arc plasma(Bristol : IOP Publ., 2017-05-15) Baeva, M.; Uhrlandt, D.; Murphy, A.B.A collisional-radiative model for the ground state and fifty effective excited levels of atomic iron, and one level for singly-ionized iron, is set up for technological plasmas. Attention is focused on the population of excited states of atomic iron as a result of excitation, de-excitation, ionization, recombination and spontaneous emission. Effective rate coefficients for ionization and recombination, required in non-equilibrium plasma transport models, are also obtained. The collisional-radiative model is applied to a thermal arc plasma. Input parameters for the collisional-radiative model are provided by a magnetohydrodynamic simulation of a gas-metal welding arc, in which local thermodynamic equilibrium is assumed and the treatment of the transport of metal vapour is based on combined diffusion coefficients. The results clearly identify the conditions in the arc, under which the atomic state distribution satisfies the Boltzmann distribution, with an excitation temperature equal to the plasma temperature. These conditions are met in the central part of the arc, even though a local temperature minimum occurs here. This provides assurance that diagnostic methods based on local thermodynamic equilibrium, in particular those of optical emission spectroscopy, are reliable here. In contrast, deviations from the equilibrium atomic-state distribution are obtained in the near-electrode and arc fringe regions. As a consequence, the temperatures determined from the ratio of line intensities and number densities obtained from the emission coefficient in these regions are questionable. In this situation, the collisional-radiative model can be used as a diagnostic tool to assist in the interpretation of spectroscopic measurements.
- ItemComparative studies of low-intensity short-length arcs(Praha : Czech Technical University in Prague, Faculty of Electrical Engineering, Department of Physics, 2019) Baeva, M.; Siewert, E.; Uhrlandt, D.We present results obtained by two non-equilibrium modelling approaches and experiments on low-intensity short-length arcs in argon at atmospheric pressure. The first one considers a quasi-neutral arc column combined with boundary conditions on the electrodes based on the energy balance in the space-charge sheaths. The second approach applies a unified description over the entire gap and solves the Poisson equation for the self-consistent electric field. The experiments provide the arc voltage.
- ItemDetermination of Cr Density in the Active Phase of a High-current Vacuum Arcs(Praha : Czech Technical University in Prague, Faculty of Electrical Engineering, Department of Physics, 2017) Gortschakow, S.; Khakpour, A.; Popov, S.; Franke, S.; Methling, R.; Uhrlandt, D.Melting and evaporation of the anode surface strongly influence the interruption capability of vacuum circuit breakers, because they lead to injection of atomic vapour into the inter-electrode gap. Determination of the vapour density and its dynamics with respect to different anode phenomena is therefore of great importance. Results of Cr density measurements in a high-current vacuum arc by using broadband absorption spectroscopy are presented. The vapour density of atomic Cr is determined after the formation of anode spots as well as close to the current zero. Cr I resonance lines at 425.43 nm have been used for the analysis. An AC current pulse with maximum value of 7 kA and a frequency of 100 Hz is applied to a vacuum arc between two cylindrical butt electrodes made of CuCr7525 with a diameter of 10 mm. The high-current anode modes are observed by means of high-speed camera imaging. The temporal evolution of the Cr ground state density is presented and discussed.
- ItemEmission Spectroscopy During High-Current Anode Modes in Vacuum Arc(Praha : Czech Technical University in Prague, Faculty of Electrical Engineering, Department of Physics, 2017) Khakpour, A.; Methling, R.; Franke, S.; Gortschakow, S.; Uhrlandt, D.A vacuum interrupter reaches its interruption limit once high-current anode phenomena occur. High-current anode modes lead to an increase of the anode surface temperature and an increased generation of metal vapor, which may result in a weakening of the dielectric recovery strength after current zero. In this work, different discharge modes in a vacuum arc for AC 50 Hz including diffuse, footpoint, anode spot type 1 and type 2, and anode plume are investigated. Electrodes made of CuCr7525 with diameter of 10 mm are used. The final gap length is about 20 mm. Time and space resolved optical emission spectroscopy is used to examine the temporal and spatial distribution of atomic and ionic copper lines. The distribution of atomic and ionic lines parallel and perpendicular to the anode surface is investigated. Radiator density is also determined for CuI, CuII, and CuIII near the anode surface.
- ItemInfluence of the arc plasma parameters on the weld pool profile in TIG welding(Bristol : Institute of Physics Publishing, 2014) Toropchin, A.; Frolov, V.; Pipa, A.V.; Kozakov, R.; Uhrlandt, D.Magneto-hydrodynamic simulations of the arc and fluid simulations of the weld pool can be beneficial in the analysis and further development of arc welding processes and welding machines. However, the appropriate coupling of arc and weld pool simulations needs further improvement. The tungsten inert gas (TIG) welding process is investigated by simulations including the weld pool. Experiments with optical diagnostics are used for the validation. A coupled computational model of the arc and the weld pool is developed using the software ANSYS CFX. The weld pool model considers the forces acting on the motion of the melt inside and on the surface of the pool, such as Marangoni, drag, electromagnetic forces and buoyancy. The experimental work includes analysis of cross-sections of the workpieces, highspeed video images and spectroscopic measurements. Experiments and calculations have been performed for various currents, distances between electrode and workpiece and nozzle diameters. The studies show the significant impact of material properties like surface tension dependence on temperature as well as of the arc structure on the weld pool behaviour and finally the weld seam depth. The experimental weld pool profiles and plasma temperatures are in good agreement with computational results.
- ItemInteraction of a free burning arc with regenerative protective layers(Bristol : Institute of Physics Publishing, 2014) Uhrlandt, D.; Gorchakov, S.; Brueser, V.; Franke, S.; Khakpour, A.; Lisnyak, M.; Methling, R.; Schoenemann, T.The possible use of protective layers made of ceramic powders for walls in thermal plasma applications is studied. A stable free burning arc of currents up to 5 kA between copper- tungsten electrodes is used to analyse the arc interaction with samples coated by mixtures of CaCO3, MgCO3, and Mg(OH)2 with plaster. By means of optical emission spectroscopy the maximum arc temperature and the radiation impact on the surfaces are estimated to be around 15000 K and 20 MWm-2, respectively. Thermographic measurements confirm the efficient protection of substrates by all layer materials. Layers containing CaCO3 lead to the lowest heating of ceramic samples which may be caused by a strong evaporation of the layer material.
- ItemInvestigation of an Ablation-dominated Arc in a Model Chamber by Optical Emission Spectroscopy(Praha : Czech Technical University in Prague, Faculty of Electrical Engineering, Department of Physics, 2017) Methling, R.; Khakpour, A.; Wetzeler, S.; Uhrlandt, D.A switching arc in a model chamber is investigated by means of optical emission spectroscopy. Ignition wire is applied to initiate an arc of several kiloampere between tungsten−copper electrodes. Radiation emitted by the arc plasma is absorbed by a surrounding PTFE nozzle, leading to an ablation–dominated discharge. Video spectroscopy is carried out using an imaging spectrometer combined with a high–speed video camera. Carbon ion and fluorine atom line emission from the heating channel as well as copper, oxygen and nitrogen from ignition wire and ambient air are analyzed with focus on the low–current phases at the beginning of discharge and near current zero. Additionally, electrical parameters and total pressure are recorded while the general behavior of the discharge is observed by another video camera. Considering rotational symmetry of the arc the corresponding radial emission coefficients are determined. Finally, radial temperature profiles are calculated.
- ItemSignificance of the Resonance Condition for Controlling the Seam Position in Laser-assisted TIG Welding(Amsterdam [u.a.] : Elsevier, 2016) Emde, B.; Huse, M.; Hermsdorf, J.; Kaierle, S.; Wesling, V.; Overmeyer, L.; Kozakov, R.; Uhrlandt, D.As an energy-preserving variant of laser hybrid welding, laser-assisted arc welding uses laser powers of less than 1 kW. Recent studies have shown that the electrical conductivity of a TIG welding arc changes within the arc in case of a resonant interaction between laser radiation and argon atoms. This paper presents investigations on how to control the position of the arc root on the workpiece by means of the resonant interaction. Furthermore, the influence on the welding result is demonstrated. The welding tests were carried out on a cooled copper plate and steel samples with resonant and non-resonant laser radiation. Moreover, an analysis of the weld seam is presented.