Search Results

Now showing 1 - 10 of 11
Loading...
Thumbnail Image
Item

Vertical profiles of aerosol mass concentration derived by unmanned airborne in situ and remote sensing instruments during dust events

2018, Mamali, Dimitra, Marinou, Eleni, Sciare, Jean, Pikridas, Michael, Kokkalis, Panagiotis, Kottas, Michael, Binietoglou, Ioannis, Tsekeri, Alexandra, Keleshis, Christos, Engelmann, Ronny, Baars, Holger, Ansmann, Albert, Amiridis, Vassilis, Russchenberg, Herman, Biskos, George

In situ measurements using unmanned aerial vehicles (UAVs) and remote sensing observations can independently provide dense vertically resolved measurements of atmospheric aerosols, information which is strongly required in climate models. In both cases, inverting the recorded signals to useful information requires assumptions and constraints, and this can make the comparison of the results difficult. Here we compare, for the first time, vertical profiles of the aerosol mass concentration derived from light detection and ranging (lidar) observations and in situ measurements using an optical particle counter on board a UAV during moderate and weak Saharan dust episodes. Agreement between the two measurement methods was within experimental uncertainty for the coarse mode (i.e. particles having radii > 0.5 μm), where the properties of dust particles can be assumed with good accuracy. This result proves that the two techniques can be used interchangeably for determining the vertical profiles of aerosol concentrations, bringing them a step closer towards their systematic exploitation in climate models.

Loading...
Thumbnail Image
Item

Measurement report: Balloon-borne in situ profiling of Saharan dust over Cyprus with the UCASS optical particle counter

2021, Kezoudi, Maria, Tesche, Matthias, Smith, Helen, Tsekeri, Alexandra, Baars, Holger, Dollner, Maximilian, Estellés, Víctor, Bühl, Johannes, Weinzierl, Bernadett, Ulanowski, Zbigniew, Müller, Detlef, Amiridis, Vassilis

This paper presents measurements of mineral dust concentration in the diameter range from 0.4 to 14.0 µm with a novel balloon-borne optical particle counter, the Universal Cloud and Aerosol Sounding System (UCASS). The balloon launches were coordinated with ground-based active and passive remote-sensing observations and airborne in situ measurements with a research aircraft during a Saharan dust outbreak over Cyprus from 20 to 23 April 2017. The aerosol optical depth at 500 nm reached values up to 0.5 during that event over Cyprus, and particle number concentrations were as high as 50 cm−3 for the diameter range between 0.8 and 13.9 µm. Comparisons of the total particle number concentration and the particle size distribution from two cases of balloon-borne measurements with aircraft observations show reasonable agreement in magnitude and shape despite slight mismatches in time and space. While column-integrated size distributions from balloon-borne measurements and ground-based remote sensing show similar coarse-mode peak concentrations and diameters, they illustrate the ambiguity related to the missing vertical information in passive sun photometer observations. Extinction coefficient inferred from the balloon-borne measurements agrees with those derived from coinciding Raman lidar observations at height levels with particle number concentrations smaller than 10 cm−3 for the diameter range from 0.8 to 13.9 µm. An overestimation of the UCASS-derived extinction coefficient of a factor of 2 compared to the lidar measurement was found for layers with particle number concentrations that exceed 25 cm−3, i.e. in the centre of the dust plume where particle concentrations were highest. This is likely the result of a variation in the refractive index and the shape and size dependency of the extinction efficiency of dust particles along the UCASS measurements. In the future, profile measurements of the particle number concentration and particle size distribution with the UCASS could provide a valuable addition to the measurement capabilities generally used in field experiments that are focussed on the observation of coarse aerosols and clouds.

Loading...
Thumbnail Image
Item

Lidar Ice nuclei estimates and how they relate with airborne in-situ measurements

2018, Marinou, Eleni, Amiridis, Vassilis, Ansmann, Albert, Nenes, Athanasios, Balis, Dimitris, Schrod, Jann, Binietoglou, Ioannis, Solomos, Stavros, Mamali, Dimitra, Engelmann, Ronny, Baars, Holger, Kottas, Michael, Tsekeri, Alexandra, Proestakis, Emmanouil, Kokkalis, Panagiotis, Goloub, Philippe, Cvetkovic, Bojan, Nichovic, Slobodan, Mamouri, Rodanthi, Pikridas, Michael, Stavroulas, Iasonas, Keleshis, Christos, Sciare, Jean

By means of available ice nucleating particle (INP) parameterization schemes we compute profiles of dust INP number concentration utilizing Polly-XT and CALIPSO lidar observations during the INUIT-BACCHUS-ACTRIS 2016 campaign. The polarization-lidar photometer networking (POLIPHON) method is used to separate dust and non-dust aerosol backscatter, extinction, mass concentration, particle number concentration (for particles with radius > 250 nm) and surface area concentration. The INP final products are compared with aerosol samples collected from unmanned aircraft systems (UAS) and analyzed using the ice nucleus counter FRIDGE.

Loading...
Thumbnail Image
Item

3D Structure of Saharan Dust Transport Towards Europe as Seen by CALIPSO

2016, Marinou, Eleni, Amiridis, Vassilis, Tsekeri, Alexandra, Solomos, Stavros, Kokkalis, Panos, Proestakis, Emmanouil, Kottas, Michael, Binietoglou, Ioannis, Zanis, Prodromos, Kazadzis, Stelios, Wandinger, Ulla, Ansmann, Albert

We present a 3D multi-year monthly mean climatology of Saharan dust advection over Europe using an area-optimized pure dust CALIPSO product. The product has been developed by applying EARLINET-measured dust lidar ratios and depolarization-based dust discrimination methods and it is shown to have a very good agreement in terms of AOD when compared to AERONET over Europe/North Africa and MODIS over Mediterranean. The processing of such purely observational data reveals the certain seasonal patterns of dust transportation towards Europe and the Atlantic Ocean. The physical and optical properties of the dust layer are identified for several areas near the Saharan sources, over the Mediterranean and over continental Europe.

Loading...
Thumbnail Image
Item

GARRLiC and LIRIC: Strengths and limitations for the characterization of dust and marine particles along with their mixtures

2017, Tsekeri, Alexandra, Lopatin, Anton, Amiridis, Vassilis, Marinou, Eleni, Igloffstein, Julia, Siomos, Nikolaos, Solomos, Stavros, Kokkalis, Panagiotis, Engelmann, Ronny, Baars, Holger, Gratsea, Myrto, Raptis, Panagiotis I., Binietoglou, Ioannis, Mihalopoulos, Nikolaos, Kalivitis, Nikolaos, Kouvarakis, Giorgos, Bartsotas, Nikolaos, Kallos, George, Basart, Sara, Schuettemeyer, Dirk, Wandinger, Ulla, Ansmann, Albert, Chaikovsky, Anatoli P., Dubovik, Oleg

The Generalized Aerosol Retrieval from Radiometer and Lidar Combined data algorithm (GARRLiC) and the LIdar-Radiometer Inversion Code (LIRIC) provide the opportunity to study the aerosol vertical distribution by combining ground-based lidar and sun-photometric measurements. Here, we utilize the capabilities of both algorithms for the characterization of Saharan dust and marine particles, along with their mixtures, in the south-eastern Mediterranean during the CHARacterization of Aerosol mixtures of Dust and Marine origin Experiment (CHARADMExp). Three case studies are presented, focusing on dust-dominated, marinedominated and dust-marine mixing conditions. GARRLiC and LIRIC achieve a satisfactory characterization for the dust-dominated case in terms of particle microphysical properties and concentration profiles. The marine-dominated and the mixture cases are more challenging for both algorithms, although GARRLiC manages to provide more detailed microphysical retrievals compared to AERONET, while LIRIC effectively discriminates dust and marine particles in its concentration profile retrievals. The results are also compared with modelled dust and marine concentration profiles and surface in situ measurements.

Loading...
Thumbnail Image
Item

Retrieval of ice-nucleating particle concentrations from lidar observations and comparison with UAV in situ measurements

2019, Marinou, Eleni, Tesche, Matthias, Nenes, Athanasios, Ansmann, Albert, Schrod, Jann, Mamali, Dimitra, Tsekeri, Alexandra, Pikridas, Michael, Baars, Holger, Engelmann, Ronny, Voudouri, Kalliopi-Artemis, Solomos, Stavros, Sciare, Jean, Groß, Silke, Ewald, Florian, Amiridis, Vassilis

Aerosols that are efficient ice-nucleating particles (INPs) are crucial for the formation of cloud ice via heterogeneous nucleation in the atmosphere. The distribution of INPs on a large spatial scale and as a function of height determines their impact on clouds and climate. However, in situ measurements of INPs provide sparse coverage over space and time. A promising approach to address this gap is to retrieve INP concentration profiles by combining particle concentration profiles derived by lidar measurements with INP efficiency parameterizations for different freezing mechanisms (immersion freezing, deposition nucleation). Here, we assess the feasibility of this new method for both ground-based and spaceborne lidar measurements, using in situ observations collected with unmanned aerial vehicles (UAVs) and subsequently analyzed with the FRIDGE (FRankfurt Ice nucleation Deposition freezinG Experiment) INP counter from an experimental campaign at Cyprus in April 2016. Analyzing five case studies we calculated the cloud-relevant particle number concentrations using lidar measurements (n250,dry with an uncertainty of 20 % to 40 % and Sdry with an uncertainty of 30 % to 50 %), and we assessed the suitability of the different INP parameterizations with respect to the temperature range and the type of particles considered. Specifically, our analysis suggests that our calculations using the parameterization of Ullrich et al. (2017) (applicable for the temperature range −50 to −33 ∘C) agree within 1 order of magnitude with the in situ observations of nINP; thus, the parameterization of Ullrich et al. (2017) can efficiently address the deposition nucleation pathway in dust-dominated environments. Additionally, our calculations using the combination of the parameterizations of DeMott et al. (2015, 2010) (applicable for the temperature range −35 to −9 ∘C) agree within 2 orders of magnitude with the in situ observations of INP concentrations (nINP) and can thus efficiently address the immersion/condensation pathway of dust and nondust particles. The same conclusion is derived from the compilation of the parameterizations of DeMott et al. (2015) for dust and Ullrich et al. (2017) for soot.

Loading...
Thumbnail Image
Item

Is the near-spherical shape the "new black" for smoke?

2020, Gialitaki, Anna, Tsekeri, Alexandra, Amiridis, Vassilis, Ceolato, Romain, Paulien, Lucas, Kampouri, Anna, Gkikas, Antonis, Solomos, Stavros, Marinou, Eleni, Haarig, Moritz, Baars, Holger, Ansmann, Albert, Lapyonok, Tatyana, Lopatin, Anton, Dubovik, Oleg, Groß, Silke, Wirth, Martin, Tsichla, Maria, Tsikoudi, Ioanna, Balis, Dimitris

We examine the capability of near-sphericalshaped particles to reproduce the triple-wavelength particle linear depolarization ratio (PLDR) and lidar ratio (LR) values measured over Europe for stratospheric smoke originating from Canadian wildfires. The smoke layers were detected both in the troposphere and the stratosphere, though in the latter case the particles presented PLDR values of almost 18% at 532 nm as well as a strong spectral dependence from the UV to the near-IR wavelength. Although recent simulation studies of rather complicated smoke particle morphologies have shown that heavily coated smoke aggregates can produce large PLDR, herein we propose a much simpler model of compact near-spherical smoke particles. This assumption allows for the reproduction of the observed intensive optical properties of stratospheric smoke, as well as their spectral dependence. We further examine whether an extension of the current Aerosol Robotic Network (AERONET) scattering model to include the near-spherical shapes could be of benefit to the AERONET retrieval for stratospheric smoke cases associated with enhanced PLDR. Results of our study illustrate the fact that triple-wavelength PLDR and LR lidar measurements can provide us with additional insight when it comes to particle characterization. © 2020 Author(s).

Loading...
Thumbnail Image
Item

Lidar-Radiometer Inversion Code (LIRIC) for the retrieval of vertical aerosol properties from combined lidar/radiometer data: Development and distribution in EARLINET

2016, Chaikovsky, Anatoli, Dubovik, Oleg, Holben, Brent, Bril, Andrey, Goloub, Philippe, Tanré, Didier, Pappalardo, Gelsomina, Wandinger, Ulla, Chaikovskaya, Ludmila, Denisov, Sergey, Grudo, Jan, Lopatin, Anton, Karol, Yana, Lapyonok, Tatsiana, Amiridis, Vassilis, Ansmann, Albert, Apituley, Arnoud, Allados-Arboledas, Lucas, Binietoglou, Ioannis, Boselli, Antonella, D'Amico, Giuseppe, Freudenthaler, Volker, Giles, David, Granados-Muñoz, María José, Kokkalis, Panayotis, Nicolae, Doina, Oshchepkov, Sergey, Papayannis, Alex, Perrone, Maria Rita, Pietruczuk, Alexander, Rocadenbosch, Francesc, Sicard, Michaël, Slutsker, Ilya, Talianu, Camelia, De Tomasi, Ferdinando, Tsekeri, Alexandra, Wagner, Janet, Wang, Xuan

This paper presents a detailed description of LIRIC (LIdar-Radiometer Inversion Code) algorithm for simultaneous processing of coincident lidar and radiometric (sun photometric) observations for the retrieval of the aerosol concentration vertical profiles. As the lidar/radiometric input data we use measurements from European Aerosol Research Lidar Network (EARLINET) lidars and collocated sun-photometers of Aerosol Robotic Network (AERONET). The LIRIC data processing provides sequential inversion of the combined lidar and radiometric data. The algorithm starts with the estimations of column-integrated aerosol parameters from radiometric measurements followed by the retrieval of height dependent concentrations of fine and coarse aerosols from lidar signals using integrated column characteristics of aerosol layer as a priori constraints. The use of polarized lidar observations allows us to discriminate between spherical and non-spherical particles of the coarse aerosol mode. The LIRIC software package was implemented and tested at a number of EARLINET stations. Intercomparison of the LIRIC-based aerosol retrievals was performed for the observations by seven EARLINET lidars in Leipzig, Germany on 25 May 2009. We found close agreement between the aerosol parameters derived from different lidars that supports high robustness of the LIRIC algorithm. The sensitivity of the retrieval results to the possible reduction of the available observation data is also discussed.

Loading...
Thumbnail Image
Item

Three-dimensional evolution of Saharan dust transport towards Europe based on a 9-year EARLINET-optimized CALIPSO dataset

2017, Marinou, Eleni, Amiridis, Vassilis, Binietoglou, Ioannis, Tsikerdekis, Athanasios, Solomos, Stavros, Proestakis, Emannouil, Konsta, Dimitra, Papagiannopoulos, Nikolaos, Tsekeri, Alexandra, Vlastou, Georgia, Zanis, Prodromos, Balis, Dimitrios, Wandinger, Ulla, Ansmann, Albert

In this study we use a new dust product developed using CALIPSO (Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observation) observations and EARLINET (European Aerosol Research Lidar Network) measurements and methods to provide a 3-D multiyear analysis on the evolution of Saharan dust over North Africa and Europe. The product uses a CALIPSO L2 backscatter product corrected with a depolarization-based method to separate pure dust in external aerosol mixtures and a Saharan dust lidar ratio (LR) based on long-term EARLINET measurements to calculate the dust extinction profiles. The methodology is applied on a 9-year CALIPSO dataset (2007-2015) and the results are analyzed here to reveal for the first time the 3-D dust evolution and the seasonal patterns of dust over its transportation paths from the Sahara towards the Mediterranean and Continental Europe. During spring, the spatial distribution of dust shows a uniform pattern over the Sahara desert. The dust transport over the Mediterranean Sea results in mean dust optical depth (DOD) values up to 0.1. During summer, the dust activity is mostly shifted to the western part of the desert where mean DOD near the source is up to 0.6. Elevated dust plumes with mean extinction values between 10 and 75 Mm-1 are observed throughout the year at various heights between 2 and 6 km, extending up to latitudes of 40° N. Dust advection is identified even at latitudes of about 60° N, but this is due to rare events of episodic nature. Dust plumes of high DOD are also observed above the Balkans during the winter period and above northwest Europe during autumn at heights between 2 and 4 km, reaching mean extinction values up to 50 Mm-1. The dataset is considered unique with respect to its potential applications, including the evaluation of dust transport models and the estimation of cloud condensation nuclei (CCN) and ice nuclei (IN) concentration profiles. Finally, the product can be used to study dust dynamics during transportation, since it is capable of revealing even fine dynamical features such as the particle uplifting and deposition on European mountainous ridges such as the Alps and Carpathian Mountains.

Loading...
Thumbnail Image
Item

Application of the Garrlic algorithm for the characterization of dust and marine particles utilizing the lidar-sunphotometer synergy

2016, Tsekeri, Alexandra, Amiridis, Vassilis, Lopatin, Anton, Marinou, Eleni, Kokkalis, Panos, Solomos, Stavros, Engelmann, Ronny, Baars, Holger, Wandinger, Ulla, Ansmann, Albert, Schüttemeyer, Dirk, Dubovik, Oleg

The importance of studying the vertical distribution of aerosol plumes is prominent in regional and climate studies. The new Generalized Aerosol Retrieval from Radiometer and Lidar Combined data algorithm (GARRLiC) provides this opportunity combining active and passive ground-based remote sensing from lidar and sunphotometer measurements. Here, we utilize GARRLiC capabilities for the characterization of Saharan dust and marine particles at the Eastern Mediterranean region during the Characterization of Aerosol mixtures of Dust And Marine origin Experiment (CHARADMExp). Two different case studies are presented, a dust-dominated case which we managed to characterize successfully in terms of the particle microphysical properties and their vertical distribution and a case of two separate layers of marine and dust particles for which the characterization proved to be more challenging.