5 results
Search Results
Now showing 1 - 5 of 5
- ItemComparative study of sculptured metallic thin films deposited by oblique angle deposition at different temperatures(Frankfurt, M. : Beilstein-Institut zur Förderung der Chemischen Wissenschaften, 2018) Liedtke, Susann; Grüner, Christoph; Gerlach, Jürgen W.; Rauschenbach, BerndMetals with a wide range of melting points are deposited by electron beam evaporation under oblique deposition geometry on thermally oxidized Si substrates. During deposition the sample holder is cooled down to 77 K. It is observed that all obliquely deposited metals grow as tilted, high aspect ratio columns and hence with a similar morphology. A comparison of such columns with those deposited at room temperature (300 K) reveals that shadowing dominates the growth process for columns deposited at 77 K, while the impact of surface diffusion is significantly increased at elevated substrate temperatures. Furthermore, it is discussed how the incidence angle of the incoming particle flux and the substrate temperature affect the columnar tilt angles and the porosity of the sculptured thin films. Exemplarily for tilted Al columns deposited at 77 K and at 300 K, in-plane pole figure measurements are carried out. A tendency to form a biaxial texture as well as a change in the crystalline structure depending on the substrate temperature is found for those films.
- ItemDeposition of exchange-coupled dinickel complexes on gold substrates utilizing ambidentate mercapto-carboxylato ligands(Frankfurt, M. : Beilstein-Institut zur Förderung der Chemischen Wissenschaften, 2017) Börner, Martin; Blömer, Laura; Kischel, Marcus; Richter, Peter; Salvan, Georgeta; Zahn, Dietrich R. T.; Siles, Pablo F.; Fuentes, Maria E. N.; Bufon, Carlos C. B.; Grimm, Daniel; Schmidt, Oliver G.; Breite, Daniel; Abel, Bernd; Kersting, BertholdThe chemisorption of magnetically bistable transition metal complexes on planar surfaces has recently attracted increased scientific interest due to its potential application in various fields, including molecular spintronics. In this work, the synthesis of mixed-ligand complexes of the type [NiII2L(L’)](ClO4), where L represents a 24-membered macrocyclic hexaazadithiophenolate ligand and L’ is a ω-mercapto-carboxylato ligand (L’ = HS(CH2)5CO2− (6), HS(CH2)10CO2− (7), or HS(C6H4)2CO2− (8)), and their ability to adsorb on gold surfaces is reported. Besides elemental analysis, IR spectroscopy, electrospray ionization mass spectrometry (ESIMS), UV–vis spectroscopy, and X-ray crystallography (for 6 and 7), the compounds were also studied by temperature-dependent magnetic susceptibility measurements (for 7 and 8) and (broken symmetry) density functional theory (DFT) calculations. An S = 2 ground state is demonstrated by temperature-dependent susceptibility and magnetization measurements, achieved by ferromagnetic coupling between the spins of the Ni(II) ions in 7 (J = +22.3 cm−1) and 8 (J = +20.8 cm−1; H = −2JS1S2). The reactivity of complexes 6–8 is reminiscent of that of pure thiolato ligands, which readily chemisorb on Au surfaces as verified by contact angle, atomic force microscopy (AFM) and spectroscopic ellipsometry measurements. The large [Ni2L] tail groups, however, prevent the packing and self-assembly of the hydrocarbon chains. The smaller film thickness of 7 is attributed to the specific coordination mode of the coligand. Results of preliminary transport measurements utilizing rolled-up devices are also reported.
- ItemHeterobimetallic conducting polymers based on salophen complexes via electrosynthesis(London [u.a.] : RSC, 2023) Bia, Francesca; Gualandi, Isacco; Griebel, Jan; Rasmussen, Leon; Hallak, Bassam; Tonelli, Domenica; Kersting, BertholdIn this work, we report the first electrochemical synthesis of two copolymeric bimetallic conducting polymers by a simple anodic electropolymerization method. The adopted precursors are electroactive transition metal (M = Ni, Cu and Fe) salophen complexes, which can be easily obtained by direct chemical synthesis. The resulting films, labeled poly-NiCu and poly-CuFe, were characterized by cyclic voltammetry in both organic and aqueous media, attenuated total reflectance Fourier transform infrared spectroscopy, UV-vis spectroscopy, scanning electron microscopy, and coupled energy dispersive X-ray spectroscopy. The films are conductive and exhibit great electrochemical stability in both organic and aqueous media (resistant over 100 cycles without significant loss in current response or changes in electrochemical behavior), which makes them good candidates for an array of potential applications. Electrochemical detection of ascorbic acid was performed using both materials.
- ItemResearch Update: Van-der-Waals epitaxy of layered chalcogenide Sb2Te3 thin films grown by pulsed laser deposition(Melville, NY : AIP Publ., 2017) Hilmi, Isom; Lotnyk, Andriy; Gerlach, Jürgen W.; Schumacher, Philipp; Rauschenbach, BerndAn attempt to deposit a high quality epitaxial thin film of a two-dimensionally bonded (layered) chalcogenide material with van-der-Waals (vdW) epitaxy is of strong interest for non-volatile memory application. In this paper, the epitaxial growth of an exemplary layered chalcogenide material, i.e., stoichiometric Sb2Te3 thin films, is reported. The films were produced on unreconstructed highly lattice-mismatched Si(111) substrates by pulsed laser deposition (PLD). The films were grown by vdW epitaxy in a two-dimensional mode. X-ray diffraction measurements and transmission electron microscopy revealed that the films possess a trigonal Sb2Te3 structure. The single atomic Sb/Te termination layer on the Si surface was formed initializing the thin film growth. This work demonstrates a straightforward method to deposit vdW-epitaxial layered chalcogenides and, at the same time, opens up the feasibility to fabricate chalcogenide vdW heterostructures by PLD.
- ItemMicro-embossing of micro-structures in RSA-501 as mold inserts for the replication of micro-lens arrays(Amsterdam : Elsevier, 2022) Kober, Julian; Rolón, Daniel; Hölzel, Florian; Kühne, Stefan; Oberschmidt, Dirk; Arnold, ThomasThe production of mold inserts for the replication of micro-lens arrays through micro-embossing could be an alternative process route compared to diamond turning or milling in order to reduce time and costs. The rapidly solidified aluminum alloy RSA-501 is expected to form micro-structures with low surface roughness because of its ultra-fine grain structure. In micro-embossing challenges like elastic spring back effect, pile-ups, and forming accuracy depend on the material behavior. Therefore, RSA-501 was further characterized and the influence of polishing or flycutting on the material behavior was investigated. To further understand the grain and microstructure samples were sectioned along their cross and longitudinal directions. The grain structure of RSA-501 was oriented along the extrusion direction and the mean grain sizes were <1.00 μm. Furthermore, RSA-501 was micro-embossed to investigate the influence of the material behavior and surface preparation on the forming of micro-structures. The induced surface integrity through flycutting was not deep enough to influence the forming of micro-structures. Therefore, the workpiece surface can be prepared either by polishing or flycutting. When micro-embossing RSA-501, cross and longitudinal sections can be used. However, it is recommended to process the cross section because of its isotropic grain structure. It was shown that the curvature radius of micro-embossed concave structures differs from the tool radius. This is due to the elastic spring back effect. Since the embossed structure remains spherical, the spring back effect can be compensated by adjusting the tool radius.