Search Results
Strong Wet and Dry Adhesion by Cupped Microstructures
2019, Wang, Y., Kang, V., Arzt, E., Federle, W., Hensel, R.
Recent advances in bio-inspired microfibrillar adhesives have resulted in technologies that allow reliable attachment to a variety of surfaces. Because capillary and van der Waals forces are considerably weakened underwater, fibrillar adhesives are however far less effective in wet environments. Although various strategies have been proposed to achieve strong reversible underwater adhesion, strong adhesives that work both in air and underwater without additional surface treatments have yet to be developed. In this study, we report a novel design - cupped microstructures (CM) - that generates strong controllable adhesion in air and underwater. We measured the adhesive performance of cupped polyurethane microstructures with three different cup angles (15, 30, and 45°) and the same cup diameter of 100 μm in dry and wet conditions in comparison to standard mushroom-shaped microstructures (MSMs) of the same dimensions. In air, 15°CM performed comparably to the flat MSM of the same size with an adhesion strength (force per real contact area) of up to 1.3 MPa, but underwater, 15°CM achieved 20 times stronger adhesion than MSM (∼1 MPa versus ∼0.05 MPa). Furthermore, the cupped microstructures exhibit self-sealing properties, whereby stronger pulls lead to longer stable attachment and much higher adhesion through the formation of a better seal. © 2019 American Chemical Society.
Switchable double-sided micropatterned adhesives for selective fixation and detachment
2019, Tinnemann, V., Arzt, E., Hensel, R.
Micropatterned dry adhesives are promising candidates for the development of innovative adhesive platforms. Their reversible adhesion to various materials and surfaces has been reported over more than a decade. Switching between a strong and a weak adhesive state can be introduced by elastic buckling instabilities of the microstructure. In this work, we report on novel adhesive pads that exhibit micropatterned pillars on both sides. In double-sided PDMS micropatterns, the dimensions of the pillar structures were tuned by modulating the critical force for buckling during compressive loading. In this way, selective detachment of glass substrates was induced from one side of the pad. Our results indicate a significant switching efficiency of up to 83% between the strong and weak adhesive state. The new structures have high potential for emerging applications where temporary, double-sided fixations in combination with a predetermined detachment location are required. © 2018
Roll-to-roll manufacturing of micropatterned adhesives by template compression
2018, Yu, D., Beckelmann, D., Opsölder, M., Schäfer, B., Moh, K., Hensel, R., de, Oliveira, P., Arzt, E.
For the next generation of handling systems, reversible adhesion enabled by micropatterned dry adhesives exhibits high potential. The versatility of polymeric micropatterns in handling objects made from various materials has been demonstrated by several groups. However, specimens reported in most studies have been restricted to the laboratory scale. Upscaling the size and quantity of micropatterned adhesives is the next step to enable successful technology transfer. Towards this aim, we introduce a continuous roll-to-roll replication process for fabrication of high-performance, mushroom-shaped micropatterned dry adhesives. The micropatterns were made from UV-curable polyurethane acrylates. To ensure the integrity of the complex structure during the fabrication process, flexible templates were used. The compression between the template and the wet prepolymer coating was investigated to optimize replication results without structural failures, and hence, to improve adhesion. As a result, we obtained micropatterned adhesive tapes, 10 cm in width and several meters in length, with adhesion strength about 250 kPa to glass, suitable for a wide range of applications. © 2018 by the authors.
Numerical simulation of the edge stress singularity and the adhesion strength for compliant mushroom fibrils adhered to rigid substrates
2016, Balijepalli, R.G., Begley, M.R., Fleck, N.A., McMeeking, R.M., Arzt, E.
Bio-inspired adhesion of micropatterned surfaces due to intermolecular interactions has attracted much research interest over the last decade. Experiments show that the best adhesion is achieved with compliant “mushroom”-shaped fibrils. This paper analyses numerically the effects of different mushroom shapes on adhesion to a rigid substrate. When a remote stress is applied on the free end of a fibril perfectly bonded to a rigid substrate, the resultant stress distribution along the fibril is found to change dramatically between the straight punch and mushroom fibrils. A singular stress field is present at the edge of the fibril where it contacts the substrate and, in this work, the amplitude of the singularity is evaluated for fibrils perfectly bonded to a flat substrate so that sliding cannot occur there. This exercise is carried out for fibril geometries involving combinations of different diameters and thicknesses of the mushroom cap. By assuming a pre-existing detachment length at the corner where the stress singularity lies, we predict the adhesive strength for various mushroom cap shapes. Our study shows that a smaller stalk diameter and a thinner mushroom cap lead to higher adhesive strengths. A limited number of results are also given for other shapes, including those having a fillet radius connecting the stalk to the cap. The results support the rational optimization of synthetic micropatterned adhesives.
Detachment of an adhered micropillar from a dissimilar substrate
2015, Khaderi, S.N., Fleck, N.A., Arzt, E., McMeeking, R.M.
Abstract The mechanics of detachment is analysed for 2D flat-bottomed planar pillars and 3D cylindrical pillars from a dissimilar elastic substrate. Application of an axial stress to the free end of the pillar results in a singularity in stress at the corner with the substrate. An eigenvalue analysis reveals that the stress field near the corner is dominated by two singular eigenfields having eigenvalues ( λ 1 , λ 2 ) with corresponding intensities ( H 1 , H 2 ) . The asymptotic stress field σij is of the form σ ij = H 1 r λ 1 − 1 f ij ( λ 1 , θ ) + H 2 r λ 2 − 1 f ij ( λ 2 , θ ) , where fij describe the angular dependence θ of σij, and r is the radial distance from the corner. The stress intensities ( H 1 , H 2 ) are calculated numerically, using a domain integral approach, as a function of the elastic mismatch between the pillar and substrate. The singular zone extends across approximately 10 of the pillar diameter (in 3D) or pillar width (in 2D). Interfacial failure is predicted for an assumed crack emanating from the corner of pillar and substrate. For the case of an interfacial crack that resides within the domain of corner singularity, a boundary layer analysis is performed to calculate the dependence of the interfacial stress intensity factor K upon ( H 1 , H 2 ) . When the crack extends beyond the domain of corner singularity, it is necessary to consider the full geometry in order to obtain K. A case study explores the sensitivity of the pull-off stress to the flaw size and to the degree of material mismatch. The study has implications for the optimum design of adhesive surface micropatterns, for bonding to either stiffer or more compliant substrates.
Scaling of bird wings and feathers for efficient flight
2019, Sullivan, T.N., Meyers, M.A., Arzt, E.
Aves are an incredibly diverse class of animals, ranging greatly in size and thriving in a wide variety of environments. Here, we explore the scaling trends of bird wings in connection with their flight performance. The tensile strength of avian bone is hypothesized to be a limiting factor in scaling the humerus with mass, which is corroborated by its experimentally determined allometric scaling trend. We provide a mechanics analysis that explains the scaling allometry of the wing humerus length, L H , with body weight W, L H ∝ W 0.44 . Lastly, wing feathers are demonstrated to generally scale isometrically with bird mass, with the exception of the spacing between barbules, which falls within the same range for birds of all masses. Our findings provide insight into the “design” of birds and may be translatable to more efficient bird-inspired aircraft structures. © 2019 American Association for the Advancement of Science. All rights reserved.