12 results
Search Results
Now showing 1 - 10 of 12
- ItemEnergy Flux Characterisation of Atmospheric Pressure Plasma Spray Torches with Passive Thermal Probes(Boston, Mass. : Springer, 2022) Reck, Kristian A.; Hansen, Luka; Stummer, Maximilian; Kewitz, Thorben; Testrich, Holger; Hinterer, Andreas; Foest, Rüdiger; Kersten, HolgerPassive thermal probes were applied on two different plasma spraying devices to gain a detailed understanding of the energy flux towards the substrate under atmospheric pressure. The challenge of very high thermal load was solved by using an advanced time-resolved measuring and evaluation technique. The combination with a controlled movement of the jets allowed to obtain insightful radial profiles. The energy flux to the substrate changes linearly to the electrical input power. When adding diatomic gases (H2/N2) to the gas mixture the energy flux increases significantly, suggesting a more efficient energy transport. For increasing the axial distance, the energy flux shows a quadratic reduction. The obtained radial profiles are exemplarily utilized to show the inhomogeneous effect of powder injection on the energy flux distribution.
- ItemSearching for order in atmospheric pressure plasma jets(Bristol : IOP Publ., 2017-11-10) Schäfer, Jan; Sigeneger, Florian; Šperka, Jiří; Rodenburg, Cornelia; Foest, RüdigerThe self-organized discharge behaviour occurring in a non-thermal radio-frequency plasma jet in rare gases at atmospheric pressure was investigated. The frequency of the azimuthal rotation of filaments in the active plasma volume and their inclination were measured along with the gas temperature under varying discharge conditions. The gas flow and heating were described theoretically by a three-dimensional hydrodynamic model. The rotation frequencies obtained by both methods qualitatively agree. The results demonstrate that the plasma filaments forming an inclination angle α with the axial gas velocity uz are forced to a transversal movement with the velocity uφ=tan(α)*uz, which is oriented in the inclination direction. Variations of ${u}_{\phi }$ in the model reveal that the observed dynamics minimizes the energy loss due to convective heat transfer by the gas flow. The control of the self-organization regime motivates the application of the plasma jet for precise and reproducible material processing.
- ItemPlasma-based VAD process for multiply doped glass powders and high-performance fiber preforms with outstanding homogeneity(Hoboken, NJ : Wiley Interscience, 2020) Trautvetter, Tom; Schäfer, Jan; Benzine, Omar; Methling, Ralf; Baierl, Hardy; Reichel, Volker; Dellith, Jan; Köpp, Daniel; Hempel, Frank; Stankov, Marjan; Baeva, Margarita; Foest, Rüdiger; Wondraczek, Lothar; Wondraczek, Katrin; Bartelt, HartmutAn innovative approach using the vapor axial deposition (VAD), for the preparation of silica-based high-power fiber laser preforms, is described in this study. The VAD uses a plasma deposition system operating at atmospheric pressure, fed by a single, chemically adapted solution containing precursors of laser-active dopants (e.g., Yb2O3), glass-modifier species (e.g., Al2O3), and the silica matrix. The approach enables simultaneous doping with multiple optically active species and overcomes some of the current technological limitations encountered with well-established fiber preform technologies in terms of dopant distribution, doping levels, and achievable active core diameter. The deposition of co-doped silica with outstanding homogeneity is proven by Raman spectroscopy and electron probe microanalysis. Yb2O3 concentrations are realized up to 0.3 mol% in SiO2, with simultaneous doping of 3 mol% of Al2O3.
- ItemSelf-Consistent Cathode–Plasma Coupling and Role of the Fluid Flow Approach in Torch Modeling(Boston, Mass. : Springer, 2021) Baeva, Margarita; Zhu, Tao; Kewitz, Thorben; Testrich, Holger; Foest, RüdigerA two-dimensional and stationary magnetohydrodynamic model of a plasma spray torch operated with argon is developed to predict the plasma properties in a steady operating mode. The model couples a submodel of a refractory cathode and its non-equilibrium boundary layer to a submodel of the plasma in local thermodynamic equilibrium in a self-consistent manner. The Navier–Stokes equations for a laminar and compressible flow are solved in terms of low and high Mach number numerical approaches. The results show that the Mach number can reach values close to one. Simulations are performed for electric currents of 600 A and 800 A, and gas flow rates of 40, 60, and 80 NLPM. The plasma parameters obtained by the two approaches differ, and the differences become more pronounced for higher currents and gas flow rates. The arc voltage, the electric power, and the thermal efficiency from both the low and high Mach number models of the plasma agree well with experimental findings for a current of 600 A and a flow rate of 40 NLPM. For higher currents and gas flow rates, the results of the low and high Mach number models gradually differ and underline the greater appropriateness of the high Mach number model.
- ItemThe Optimization of Dispersion and Application Techniques for Nanocarbon-Doped Mixed Matrix Gas Separation Membranes(Basel : MDPI, 2022) Hammerstein, Ruben; Schubert, Tim; Braun, Gerd; Wolf, Tobias; Barbe, Stéphan; Quade, Antje; Foest, Rüdiger; Karousos, Dionysios S.; Favvas, Evangelos P.In this work, supported cellulose acetate (CA) mixed matrix membranes (MMMs) were prepared and studied concerning their gas separation behaviors. The dispersion of carbon nanotube fillers were studied as a factor of polymer and filler concentrations using the mixing methods of the rotor–stator system (RS) and the three-roll-mill system (TRM). Compared to the dispersion quality achieved by RS, samples prepared using the TRM seem to have slightly bigger, but fewer and more homogenously distributed, agglomerates. The green γ-butyrolactone (GBL) was chosen as a polyimide (PI) polymer-solvent, whereas diacetone alcohol (DAA) was used for preparing the CA solutions. The coating of the thin CA separation layer was applied using a spin coater. For coating on the PP carriers, a short parameter study was conducted regarding the plasma treatment to affect the wettability, the coating speed, and the volume of dispersion that was applied to the carrier. As predicted by the parameter study, the amount of dispersion that remained on the carriers decreased with an increasing rotational speed during the spin coating process. The dry separation layer thickness was varied between about 1.4 and 4.7 µm. Electrically conductive additives in a non-conductive matrix showed a steeply increasing electrical conductivity after passing the so-called percolation threshold. This was used to evaluate the agglomeration behavior in suspension and in the applied layer. Gas permeation tests were performed using a constant volume apparatus at feed pressures of 5, 10, and 15 bar. The highest calculated CO2/N2 selectivity (ideal), 21, was achieved for the CA membrane and corresponded to a CO2 permeability of 49.6 Barrer.
- ItemIcing mitigation by mems-fabricated surface dielectric barrier discharge(Basel : MDPI, 2021) Lindner, Matthias; Pipa, Andrei V.; Karpen, Norbert; Hink, Rüdiger; Berndt, Dominik; Foest, Rüdiger; Bonaccurso, Elmar; Weichwald, Robert; Friedberger, Alois; Caspari, Ralf; Brandenburg, Ronny; Schreiner, RupertAvoiding ice accumulation on aerodynamic components is of enormous importance to flight safety. Novel approaches utilizing surface dielectric barrier discharges (SDBDs) are expected to be more efficient and effective than conventional solutions for preventing ice accretion on aerodynamic components. In this work, the realization of SDBDs based on thin-film substrates by means of micro-electro-mechanical-systems (MEMS) technology is presented. The anti-icing performance of the MEMS SDBDs is presented and compared to SDBDs manufactured by printed circuit board (PCB) technology. It was observed that the 35 µm thick electrodes of the PCB SDBDs favor surface icing with an initial accumulation of supercooled water droplets at the electrode impact edges. This effect was not observed for 0.3 µm thick MEMS-fabricated electrodes indicating a clear advantage for MEMS-technology SDBDs for anti-icing applications. Titanium was identified as the most suitable material for MEMS electrodes. In addition, an optimization of the MEMS-SDBDs with respect to the dielectric materials as well as SDBD design is discussed.
- ItemPlasma Spraying of Kaolinite for Preparing Reactive Alumino-Silicate Glass Coatings(Weinheim : Wiley-VCH, 2022) Warr, Laurence N.; Wolff, Thorben; Testrich, Holger; Grathoff, Georg; Kruth, Angela; Foest, RüdigerThermally treated kaolinite is used to develop a range of alumino-silicate-based precursor materials but its behavior during plasma spraying has not been well-researched. In this study, two types of kaolinite samples were investigated in the form of low defect (KGa-1b) and high defect (KGa-2) varieties. The extreme temperatures of the plasma stream (up to 20 000 K) induced flash melting to produce a highly porous alumino-silicate glass without any crystallization of new Al−Si oxide minerals. The glass is comprised largely of intact or deformed spheres (average diameters 1.14–1.44 μm), which indicates rapid quenching and solidification before impact. The subspherical structures contain up to 40 % closed pore space caused by the rapid escape of water during melting. The low-density, porous alumino-silicate glass coatings with predicted specific surface areas (>0.95 m2/g) and hardnesses >1.8 GPa represent a potentially reactive but physically stable substrate ideal for further chemical functionalization.
- ItemErforschung neuer homogener atmosphärischer Plasmen und ausgewählter Anwendungen, Akronym: ATMOSPLASMA, Teilprojekt Untersuchung des Existenzbereiches homogener Barrierenentladungen : Abschlussbericht(Greifswald : Leibniz-Institut für Plasmaforschung und Technologie, 2003) Schmidt, Martin; Foest, Rüdiger; Sigeneger, F.; Adler, F.[no abstract available]
- ItemLiquid assisted plasma enhanced chemical vapour deposition with a non-thermal plasma jet at atmospheric pressure(Amsterdam [u.a.] : Elsevier, 2016) Schäfer, Jan; Fricke, Katja; Mika, Filip; Pokorná, Zuzana; Zajíčková, Lenka; Foest, RüdigerThe present study introduces a process for the synthesis of functional films onto substrates directly from the liquid phase. The reported method is based on the initialization of the synthesis by means of an atmospheric pressure plasma jet operating with argon above a thin liquid film of the starting material. The process is demonstrated by the formation of a thin, solid SiOx film from siloxane-based liquid precursors. Changes in the chemical properties of the precursor were studied in-situ during the polymerization process on the diamond crystal by using Fourier transform infrared spectroscopy The elemental composition of the SiOxCy films was analyzed by X-ray photoelectron spectroscopy (XPS). Furthermore, XPS was applied to study the effect of post-annealing processes on the composition of the films. The obtained deposits exhibit a low concentration of carbon groups. The amount of hydroxyl groups and interstitial water can be reduced significantly by post-process annealing of the films.
- ItemOn the fundamental relation of laser schlieren deflectometry for temperature measurements in filamentary plasmas(Les Ulis : EDP Sciences, 2015) Schäfer, Jan; Bonaventura, Zdeněk; Foest, RüdigerRecently, laser schlieren deflectometry (LSD) had been successfully employed as a temperature measurement method to reveal the heat convection generated by micro filaments of a self-organized non-thermal atmospheric plasma jet. Based on the theory of the temperature measurements using LSD, in this work, three approaches for an application of the method are introduced: (i) a hyperbolic-like model of refractive index is applied which allows an analytical theory for the evaluation of the deflection angle to be developed, (ii) a Gaussian shape model for the filament temperature is implemented which is analyzed numerically and (iii) an experimental calibration of the laser deflection with a gas mixture of helium and argon is performed. Thus, these approaches demonstrate that a universal relation between the relative maximum temperature of the filament core (T1/T0) and a the maximum deflection angle δ1 of the laser beam can be written as T1/T0=(1 − δ1/δ0)−1, where δ0 is a parameter that is defined by the configuration of the experiment and by the assumed model for the shape of the temperature profile.