4 results
Search Results
Now showing 1 - 4 of 4
- ItemEvaluation of spectral induced polarization field measurements in time and frequency domain(Amsterdam [u.a.] : Elsevier Science, 2020) Martin, Tina; Günther, Thomas; Orozco, Adrian Flores; Dahlin, TorleifSpectral induced polarization (SIP) measurements have been demonstrated to correlate with important parameters in hydrogeological and environmental investigations. Although SIP measurements were often collected in the frequency domain (FDIP), recent developments have demonstrated the capabilities to solve for the frequency-dependence of the complex conductivity through measurements collected in the time domain (TDIP). Therefore, the aim of our field investigations is a comparison of the measured frequency-dependence at a broad frequency range resolved through FDIP and TDIP. In contrast to previous studies, we conducted measurements with different instruments and measuring technologies for both FDIP and TDIP. This allows for investigating the robustness of different measurements and assessing various sources of errors, for the assessment of the advantages and drawbacks from different measuring techniques. Our results demonstrate that data collected through different instruments are consistent. Apparent resistivity measurements as well as the inversion results revealed quantitatively the same values for all instruments. The measurements of the IP effect are also comparable, particularly FDIP readings in the low frequencies (< 10 Hz) revealed to be quantitatively the same for different instruments. TDIP measurements are consistent for data collected with both devices. As expected, the spatial distribution of the values is also consistent for low frequency data (in FDIP) and late times measurements in TDIP (> 0.1 s). However, data quality for higher frequencies in FDIP (i.e., early times in TDIP) show larger variations, which reflects the differences between the instruments to deal with the electromagnetic contamination of the IP data. Concluded in general, the different instruments and measuring techniques can provide consistent responses for varying signal-to-noise ratio and measuring configurations. © 2020 The Authors
- ItemComparison of novel semi-airborne electromagnetic data with multi-scale geophysical, petrophysical and geological data from Schleiz, Germany(Amsterdam [u.a.] : Elsevier Science, 2020) Steuer, Annika; Smirnova, Maria; Becken, Michael; Schiffler, Markus; Günther, Thomas; Rochlitz, Raphael; Yogeshwar, Pritam; Mörbe, Wiebke; Siemon, Bernhard; Costabel, Stephan; Preugschat, Benedikt; Ibs-von Seht, Malte; Zampa, Luigi Sante; Müller, FranzIn the framework of the Deep Electromagnetic Sounding for Mineral EXploration (DESMEX) project, we carried out multiple geophysical surveys from regional to local scales in a former mining area in the state of Thuringia, Germany. We prove the applicability of newly developed semi-airborne electromagnetic (EM) systems for mineral exploration by cross-validating inversion results with those of established airborne and ground-based investigation techniques. In addition, supporting petrophysical and geological information to our geophysical measurements allowed the synthesis of all datasets over multiple scales. An initial regional-scale reconnaissance survey was performed with BGR's standard helicopter-borne geophysical system deployed with frequency-domain electromagnetic (HEM), magnetic and radiometric sensors. In addition to geological considerations, the HEM results served as base-line information for the selection of an optimal location for the intermediate-scale semi-airborne EM experiments. The semi-airborne surveys utilized long grounded transmitters and two independent airborne receiver instruments: induction coil magnetometers and SQUID sensors. Due to the limited investigation depth of the HEM method, local-scale electrical resistivity tomography (ERT) and long-offset transient electromagnetic (LOTEM) measurements were carried out on a reference profile, enabling the validation of inversion results at greater depths. The comparison of all inversion results provided a consistent overall resistivity distribution. It further confirmed that both semi-airborne receiver instruments achieve the bandwidth and sensitivity required for the investigation of the resistivity structure down to 1 km depth and therewith the detection of deeply seated earth resources. A 3D geological model, lithological and geophysical borehole logs as well as petrophysical investigations were integrated to interpret of the geophysical results. Distinct highly-conductive anomalies with resistivities of less than 10 Om were identified as alum shales over all scales. Apart from that, the petrophysical investigations exhibited that correlating geophysical and geological information using only one single parameter, such as the electrical resistivity, is hardly possible. Therefore, we developed a first approach based on clustering methods and self-organizing maps (SOMs) that allowed us to assign geological units at the surface to a given combination of geophysical and petrophysical parameters, obtained on different scales. © 2020 The Authors
- ItemMonitoring freshwater–saltwater interfaces with SAMOS – installation effects on data and inversion(Oxford : Wiley, 2020) Ronczka, Mathias; Günther, Thomas; Grinat, Michael; Wiederhold, HelgaA major problem for the freshwater supply of coastal regions is the intrusion of saltwater into aquifers. Due to extensive extraction of freshwater to suffice increasing drinking water demands and/or in periods of reduced groundwater recharge, the equilibrium state may be disturbed. The result is an upconing or movement of the fresh–saline groundwater interface, which reduces the local drinking water resources at coastal regions or islands. The saltwater monitoring system (SAMOS) is a vertical electrode chain installed in a backfilled borehole. It provides a solution to observe the transition zone in detail, both temporally and spatially. We present monitoring data of the first year from three locations - with different geological conditions that show disturbances in the resistivity distribution that result from the drilling processes. A clayey backfilling, for example, can lead to beam-like artefacts, and a mixed fluid within the backfilling changes its bulk resistivity, both leading to misinterpretations. We performed data inversion under cylindrically symmetrical conditions in full-space in order to separate these resistivity artefacts from the undisturbed background. Data inversion reveals that it is possible to separate drilling effects on the resistivity distribution from the undisturbed background. Thus, an interpretation of the natural transition zones can be made immediately after the installation. © 2020 The Authors. Near Surface Geophysics published by John Wiley & Sons Ltd on behalf of European Association of Geoscientists and Engineers.
- ItemStructural style and neotectonic activity along the Harz Boundary Fault, northern German: a multimethod approach integrating geophysics, outcrop data and numerical simulations(Berlin ; Heidelberg : Springer, 2020) Müller, Katharina; Polom, Ulrich; Winsemann, Jutta; Steffen, Holger; Tsukamoto, Sumiko; Günther, Thomas; Igel, Jan; Spies, Thomas; Lege, Thomas; Frechen, Manfred; Franzke, Hans‑Joachim; Brandes, ChristianWe present new evidence for neotectonic activity along the Harz Boundary Fault, a Cretaceous reverse fault that represents a key structure in northern Germany. For the fault analysis, we use a multimethod approach, integrating outcrop data, luminescene dating, shear wave seismics, electrical resistivity tomography (ERT) and numerical simulations. A recent sinkhole at the SSW-ward dipping and WNW–ESE striking Harz Boundary Fault exposes a NNE-ward dipping and WNW–ESE striking planar fault surface that cuts through unconsolidated debris-flow deposits thus pointing to young Lateglacial tectonic activity. The fault shows a polyphase evolution with initial normal fault movement and a later reactivation as an oblique fault with reverse and strike-slip components. A shear wave seismic profile was acquired to analyse the geometry of the fault and show that the Harz Boundary Fault is steeply dipping and likely has branches. Partly, these branches propagate into overlying alluvial-fan deposits that are probably Pleniglacial to Lateglacial in age. The outcrop data in combination with the seismic data give evidence for a splay fault system with steep back-thrusts. One of these back-thrusts is most likely the NNE-ward dipping fault that is exposed in the sinkhole. The lateral extent of the fault was mapped with electrical resistivity tomography (ERT) profiles. The timing of fault movement was estimated based on optically stimulated luminescence dating of the faulted debris-flow deposits using both quartz and feldspar minerals. Consistent feldspar and quartz ages indicate a good bleaching of the sediment prior to deposition. The results imply fault movements post-dating ~ 15 ka. Numerical simulations of glacio isostatic adjustment (GIA)-related changes in the Coulomb failure stress regime at the Harz Boundary Fault underpin the assumption that the fault was reactivated during the Lateglacial due to stress changes induced by the decay of the Late Pleistocene (Weichselian) Fennoscandian ice sheet. © 2020, The Author(s).