Filters

2018 - 201912020 - 20222

More filters

2022 - 20233
Reset filters

Settings

Author: Heinrich, Gert × End date: 2023 × Start date: 2020 × DDC: 530 × Type: Article × WGL Institute: IPF ×

Search Results

Now showing 1 - 3 of 3
  • Thumbnail Image
    Item
    Electrical and melt rheological characterization of PC and co-continuous PC/SAN blends filled with CNTs: Relationship between melt-mixing parameters, filler dispersion, and filler aspect ratio
    (Hoboken, NJ [u.a.] : Wiley, 2018) Liebscher, Marco; Domurath, Jan; Krause, Beate; Saphiannikova, Marina; Heinrich, Gert; Pötschke, Petra
    Electrical and melt rheological properties of melt-mixed polycarbonate (PC) and co-continuous PC/poly(styrene–acrylonitrile) (SAN) blends with carbon nanotubes (CNTs) are investigated. Using two sets of mixing parameters, different states of filler dispersion are obtained. With increasing CNT dispersion, an increase in electrical resistivity near the percolation threshold of PC–CNT composites and (PC + CNT)/SAN blends is observed. This suggests that the higher mixing energies required for better dispersion also result in a more severe reduction of the CNT aspect ratio; this effect was proven by CNT length measurements. Melt rheological studies show higher reinforcing effects for composites with worse dispersion. The Eilers equation, describing the melt viscosity as function of filler content, was used to fit the data and to obtain information about an apparent aspect ratio change, which was in accordance with measured CNT length reduction. Such fitting could be also transferred to the blends and serves for a qualitatively based discussion. © 2017 Wiley Periodicals
  • Thumbnail Image
    Item
    Electrically conductive and piezoresistive polymer nanocomposites using multiwalled carbon nanotubes in a flexible copolyester: Spectroscopic, morphological, mechanical and electrical properties
    (Amsterdam [u.a.] : Elsevier, 2022) Dhakal, Kedar Nath; Khanal, Santosh; Krause, Beate; Lach, Ralf; Grellmann, Wolfgang; Le, Hai Hong; Das, Amit; Wießner, Sven; Heinrich, Gert; Pionteck, Jürgen; Adhikari, Rameshwar
    Nanocomposites of multiwalled carbon nanotubes (MWCNTs) with poly(butylene adipate-co-terephthalate) (PBAT), a flexible aromatic–aliphatic copolyester, were prepared by melt mixing followed by compression moulding to investigate their spectroscopic, morphological, mechanical and electrical properties. A comparison of the Fourier transform infrared (FTIR) spectra of the neat polymer matrix and the composites showed no difference, implying a physical mixing of the matrix and the filler. A morphological investigation revealed the formation of a continuous and interconnected MWCNT network embedded in the polymer matrix with partial agglomeration. Increasing Martens hardness and indentation modulus and decreasing maximum indentation depth with increasing filler concentration demonstrated the reinforcement of the polymer by the MWCNTs. A volume resistivity of 4.6 × 105 Ω cm of the materials was achieved by the incorporation of only 1 wt.-% of the MWCNTs, which confirmed a quite low percolation threshold (below 1 wt.-%) of the nanocomposites. The electrical volume resistivity of the flexible nanocomposites was achieved up to 1.6 × 102 Ω cm, depending on the filler content. The elongation at the break of the nanocomposites at 374% and the maximum relative resistance changes (ΔR/R0) of 20 and 200 at 0.9 and 7.5% strains, respectively, were recorded in the nanocomposites (3 wt.-% MWCNTs) within the estimated volume resistivity range. A cyclic strain experiment shows the most stable and reproducible ΔR/R0 values in the 2%–5% strain range. The electrical conductivity and piezoresistivity of the investigated nanocomposites in correlation with the mechanical properties and observed morphology make them applicable for low-strain deformation-sensing.
  • Thumbnail Image
    Item
    An Improved Conservative Direct Re-Initialization Method (ICDR) for Two-Phase Flow Simulations
    (Basel ; Beijing ; Wuhan ; Barcelona ; Belgrade : MDPI, 2021) Mostafaiyan, Mehdi; Wießner, Sven; Heinrich, Gert; Hosseini, Mahdi Salami
    We introduce an improved conservative direct re-initialization (ICDR) method (for two-phase flow problems) as a new and efficient geometrical re-distancing scheme. The ICDR technique takes advantage of two mass-conserving and fast re-distancing schemes, as well as a global mass correction concept to reduce the extent of the mass loss/gain in two- and three-dimensional (2D and 3D) problems. We examine the ICDR method, at the first step, with two 2D benchmarks: the notched cylinder and the swirling flow vortex problems. To do so, we (for the first time) extensively analyze the dependency of the regenerated interface quality on both time-step and element sizes. Then, we quantitatively assess the results by employing a defined norm value, which evaluates the deviation from the exact solution. We also present a visual assessment by graphical demonstration of original and regenerated interfaces. In the next step, we investigate the performance of the ICDR in three-dimensional (3D) problems. For this purpose, we simulate drop deformation in a simple shear flow field. We describe our reason for this choice and show that, by employing the ICDR scheme, the results of our analysis comply with the existing numerical and experimental data in the literature