Search Results
A stimulated Stokes Raman scattering-based approach for continuous wave supercontinuum generation in optical fibers
2019, Arshad, Muhammad Assad, Hartung, Alexander, Jäger, Matthias
We report on a new and simple approach for continuous wave supercontinuum generation in optical fibers. Our new approach uses the effect of stimulated Stokes Raman scattering in a low loss fiber ring laser. By continuously pumping this ring laser with up to 19 W optical power we excited up to six Stokes orders and covered a wavelength range of 500 nm. Due to the feedback mechanism of the ring layout additional nonlinear effects occurred next to the plain generation of individual Stokes peaks. Eventually, these effects broaden and merge the separated Stokes peaks and create a single, connected continuous supercontinuum. By using the effect of stimulated Stokes Raman scattering, we do not rely on anomalous dispersion and modulation instability as typically required for continuous wave supercontinuum generation. © 2019 Astro Ltd.
Independently tunable dual-wavelength fiber oscillator with synchronized pulsed emission based on a theta ring cavity and a fiber Bragg grating array
2017, Tiess, Tobias, Becker, Martin, Rothhardt, Manfred, Bartelt, Hartmut, Jäger, Matthias
We present a fiber-integrated laser enabling independent tuning of two emission wavelengths with a synchronized pulsed emission. The discrete tuning concept comprises a theta cavity fiber laser (TCFL), a fiber Bragg grating (FBG) array as a versatile spectral filter, facilitating tailored tuning ranges, and optical gating to control the emission spectrum. A novel electrical driving scheme uniquely enables independently tunable multi-wavelength emission from a single laser oscillator. Tunable dual-wavelength emission is experimentally investigated with a ytterbium (Yb)-doped TCFL using an FBG array with 11 gratings. Over a tuning range of 25 nm, 55 wavelength pairs have been demonstrated with high signal contrast (≈ 40 dB) and narrow linewidth (< 40GHz). Based on the demands of prospective applications, pulse synchronicity is studied with a fiber-based time-delay spectrometer (TDS) simultaneously measuring the joint temporal and spectral pulse properties down to a single-pulse analysis. Accordingly, tunable and fully synchronized dual-wavelength emissions have been verified by driving the TCFL with optimized electrical gating parameters. This unique operation mode achieved in a cost-efficient fiber-integrated laser design targets novel applications e.g. in nonlinear spectroscopy and biophotonics.
(INVITED)Tm:YAG crystal-derived double-clad fibers – A hybrid approach towards high gain and high efficiency Tm lasers
2022, Leich, Martin, Müller, Robert, Unger, Sonja, Schwuchow, Anka, Dellith, Jan, Lorenz, Adrian, Kobelke, Jens, Jäger, Matthias
The hybrid approach of combining a Tm:YAG laser crystal with an amorphous fused silica tube is investigated to evaluate the suitability of the resulting crystal-derived fibers for efficient double-clad fiber lasers. The fabrication process and fiber properties of these Tm fibers are investigated, focusing on the dependence of the active fiber properties on the incorporated Tm3+ concentration. Crystal rods with different doping concentrations (TmxY1-x)3Al5O12 (x = 0.02, 0.05 and 0.08) were used as starting core material for fiber drawing. The investigated fibers are mechanically stable and result in a fairly homogenous and amorphous core glass with optical absorption and emission spectra that are similar to conventional Tm:Al doped silica fibers. Regarding laser properties with 790 nm cladding pumping, we could achieve a maximum slope efficiency of 47% with an output power of 4 W. The fiber laser results are compared to a conventionally fabricated double-clad Tm fiber prepared by Modified Chemical Vapor Deposition and solution doping. To the best of our knowledge, we demonstrate the highest laser output and the highest efficiency obtained from a Tm:YAG crystal-derived fiber.
Intra-cavity measurement concept of dispersion properties with a tunable fiber-integrated laser
2019, Tiess, Tobias, Hartung, Alexander, Becker, Martin, Chojetzki, Christoph, Rothhardt, Manfred, Bartelt, Hartmut, Jäger, Matthias
The dispersion properties of fibers depict a key characteristic to model the propagation of ultra-short pulses in waveguides. In the following, a new method is presented to directly measure the dispersion properties of fibers and optical components in the time domain. The analysis is based on pulse shape variations along the tuning range of a theta cavity fiber laser (TCFL) depending on the adjusted repetition rate. The automated measurement procedure, evaluating pulse symmetry, achieves a temporal sensitivity below 5 ps surpassing the resolution of the acquisition electronics. Exemplarily, two samples of Nufern PM980-XP fiber are investigated with an Yb-doped tunable TCFL retrieving the mean dispersion parameter D? by comparative measurements. The obtained results are compared to a reference method based on spectral interferometry. With deviations in D? between either approach of 0.3% and 1.3%, respectively, the results agree well within the measurement errors of the TCFL, verifying the presented concept. Due to the pulse formation process extending over multiple round trips, this approach achieves an enhanced sensitivity compared to competing direct temporal methods. Together with an alignment free operation, the fiber-integrated TCFL depicts a simple and robust concept showing potential in specific measurement scenarios such as in quality management. © 2019 Astro Ltd.
Tm3+/Ho3+ co-doped germanate glass double-clad fiber for broadband emission and lasing above 2 µm
2019, Kochanowicz, Marcin, Zmojda, Jacek, Miluski, Piotr, Baranowska, Agata, Leich, Martin, Schwuchow, Anka, Jäger, Matthias, Kuwik, M., Pisarska, Johanna, Pisarski, Wojciech A., Dorosz, Dominik
In this paper, a 2 µm broadband emission under 796 nm laser diode excitation in low phonon energy GeO2-Ga2O3-BaO glass system is co-doped with 0.7Tm2O3/(0.07-0.7)Ho2O3 (mol%). The widest emission band (where the Tm3+ → Ho3+ energy transfer efficiency is 63%) was obtained for 0.7Tm2O3/0.15Ho2O3 co-doped glass from which a double-clad optical fiber was realized and investigated. Optimization of Tm3+/Ho3+ concentration enabled the acquisition of broadband amplified spontaneous emission (ASE) in double-clad optical fiber with a full width at half maximum (FWHM): 377 nm and 662 nm for 3 dB and 10 dB bandwidth, respectively. ASE spectrum is a result of the superposition of (Tm3+: 3H4 →Η3F4) 1.45 µm, (Tm3+: 3F4 → 3H6) 1.8 µm and (Ho3+:5I7 → 5I8) 2 µm emission bands. Hence, highly rare-earth co-doped germanate glass is characterized by a remarkably broader ASE spectrum than silica and tellurite fibers showed promising lasing properties for their further application in tunable and dual wavelength lasers.In this paper, a 2 µm broadband emission under 796 nm laser diode excitation in low phonon energy GeO2-Ga2O3-BaO glass system is co-doped with 0.7Tm2O3/(0.07-0.7)Ho2O3 (mol%). The widest emission band (where the Tm3+ → Ho3+ energy transfer efficiency is 63%) was obtained for 0.7Tm2O3/0.15Ho2O3 co-doped glass from which a double-clad optical fiber was realized and investigated. Optimization of Tm3+/Ho3+ concentration enabled the acquisition of broadband amplified spontaneous emission (ASE) in double-clad optical fiber with a full width at half maximum (FWHM): 377 nm and 662 nm for 3 dB and 10 dB bandwidth, respectively. ASE spectrum is a result of the superposition of (Tm3+: 3H4 →Η3F4) 1.45 µm, (Tm3+: 3F4 → 3H6) 1.8 µm and (Ho3+:5I7 → 5I8) 2 µm emission bands. Hence, highly rare-earth co-doped germanate glass is characterized by a remarkably broader ASE spectrum than silica and tellurite fibers showed promising lasing properties for their further application in tunable and dual wavelength lasers.
An Approach to Ring Resonator Biosensing Assisted by Dielectrophoresis: Design, Simulation and Fabrication
2020, Henriksson, Anders, Kasper, Laura, Jäger, Matthias, Neubauer, Peter, Birkholz, Mario
The combination of extreme miniaturization with a high sensitivity and the potential to be integrated in an array form on a chip has made silicon-based photonic microring resonators a very attractive research topic. As biosensors are approaching the nanoscale, analyte mass transfer and bonding kinetics have been ascribed as crucial factors that limit their performance. One solution may be a system that applies dielectrophoretic forces, in addition to microfluidics, to overcome the diffusion limits of conventional biosensors. Dielectrophoresis, which involves the migration of polarized dielectric particles in a non-uniform alternating electric field, has previously been successfully applied to achieve a 1000-fold improved detection efficiency in nanopore sensing and may significantly increase the sensitivity in microring resonator biosensing. In the current work, we designed microring resonators with integrated electrodes next to the sensor surface that may be used to explore the effect of dielectrophoresis. The chip design, including two different electrode configurations, electric field gradient simulations, and the fabrication process flow of a dielectrohoresis-enhanced microring resonator-based sensor, is presented in this paper. Finite element method (FEM) simulations calculated for both electrode configurations revealed ?E2 values above 1017 V2m-3 around the sensing areas. This is comparable to electric field gradients previously reported for successful interactions with larger molecules, such as proteins and antibodies. © 2020 by the authors. Licensee MDPI, Basel, Switzerland.
2 MW peak power generation in fluorine co-doped Yb fiber prepared by powder-sinter technology
2020, Leich, Martin, Kalide, André, Eschrich, Tina, Lorenz, Adrian, Lorenz, Martin, Wondraczek, Katrin, Schönfeld, Dörte, Langner, Andreas, Schötz, Gerhard, Jäger, Matthias
We report on the first, to the best of our knowledge, implementation of a fluorine co-doped large-mode-area REPUSIL fiber for high peak power amplification in an ultrashort-pulse master oscillator power amplifier. The core material of the investigated step-index fiber with high Yb-doping level, 52 µm core and high core-to-clad ratio of 1:4.2 was fabricated by means of the REPUSIL powder-sinter technology. The core numerical aperture was adjusted by fluorine codoping to 0.088. For achieving high beam quality and for ensuring a monolithic seed path, the LMA fiber is locally tapered. We demonstrate an Yb fiber amplifier with near-diffraction-limited beam quality of M2 = 1.3, which remains constant up to a peak power of 2 MW. This is a record for a tapered single core fiber. © 2020 Optical Society of America
Yb-doped large mode area fiber for beam quality improvement using local adiabatic tapers with reduced dopant diffusion
2018, Zhu, Yuan, Leich, Martin, Lorenz, Martin, Eschrich, Tina, Aichele, Claudia, Kobelke, Jens, Bartelt, Hartmut, Jäger, Matthias
A newly designed all-solid step-index Yb-doped aluminosilicate large mode area fiber for achieving high peak power at near diffraction limited beam quality with local adiabatic tapering is presented. The 45µm diameter fiber core and pump cladding consist of active/passively doped aluminosilicate glass produced by powder sinter technology (REPUSIL). A deliberate combination of innovative cladding and core materials was aspired to achieve low processing temperature reducing dopant diffusion during fiber fabrication, tapering and splicing. By developing a short adiabatic taper, robust seed coupling is achieved by using this Yb-doped LMA fiber as final stage of a nanosecond fiber Master Oscillator Power Amplifier (MOPA) system while maintaining near diffraction limited beam quality by preferential excitation of the fundamental mode. After application of a fiber-based endcap, the peak power could be scaled up to 375 kW with high beam quality and a measured M2 value of 1.3~1.7.A newly designed all-solid step-index Yb-doped aluminosilicate large mode area fiber for achieving high peak power at near diffraction limited beam quality with local adiabatic tapering is presented. The 45µm diameter fiber core and pump cladding consist of active/passively doped aluminosilicate glass produced by powder sinter technology (REPUSIL). A deliberate combination of innovative cladding and core materials was aspired to achieve low processing temperature reducing dopant diffusion during fiber fabrication, tapering and splicing. By developing a short adiabatic taper, robust seed coupling is achieved by using this Yb-doped LMA fiber as final stage of a nanosecond fiber Master Oscillator Power Amplifier (MOPA) system while maintaining near diffraction limited beam quality by preferential excitation of the fundamental mode. After application of a fiber-based endcap, the peak power could be scaled up to 375 kW with high beam quality and a measured M2 value of 1.3~1.7.
Observation of direction instability in a fiber ring laser
2021, Arshad, Muhammad Assad, Hartung, Alexander, Pratiwi, Arni Candra, Jäger, Matthias
We report on the observation of a new phenomenon occurring in a fiber ring laser. This phenomenon is about the transition from an initially bidirectional emission of a reciprocal fiber ring laser to a unidirectional emission at a certain pump power threshold. In addition, the final direction is not predefined but appears to be randomly chosen every time the threshold is exceeded. Therefore, we term this new phenomenon direction instability. Furthermore, we provide a first discussion of how the instability threshold is influenced by the length and the loss of the cavity. We show that the threshold follows a power times length scaling, indicating a nonlinear origin.