Filters

2014 - 20174

More filters

2020 - 20234
Reset filters

Settings

Author: Khakpour, A. × End date: 2019 × Start date: 2010 × Subject: Konferenzschrift × WGL Institute: INP ×

Search Results

Now showing 1 - 4 of 4
  • Thumbnail Image
    Item
    Investigation of an Ablation-dominated Arc in a Model Chamber by Optical Emission Spectroscopy
    (Praha : Czech Technical University in Prague, Faculty of Electrical Engineering, Department of Physics, 2017) Methling, R.; Khakpour, A.; Wetzeler, S.; Uhrlandt, D.
    A switching arc in a model chamber is investigated by means of optical emission spectroscopy. Ignition wire is applied to initiate an arc of several kiloampere between tungsten−copper electrodes. Radiation emitted by the arc plasma is absorbed by a surrounding PTFE nozzle, leading to an ablation–dominated discharge. Video spectroscopy is carried out using an imaging spectrometer combined with a high–speed video camera. Carbon ion and fluorine atom line emission from the heating channel as well as copper, oxygen and nitrogen from ignition wire and ambient air are analyzed with focus on the low–current phases at the beginning of discharge and near current zero. Additionally, electrical parameters and total pressure are recorded while the general behavior of the discharge is observed by another video camera. Considering rotational symmetry of the arc the corresponding radial emission coefficients are determined. Finally, radial temperature profiles are calculated.
  • Thumbnail Image
    Item
    Interaction of a free burning arc with regenerative protective layers
    (Bristol : Institute of Physics Publishing, 2014) Uhrlandt, D.; Gorchakov, S.; Brueser, V.; Franke, S.; Khakpour, A.; Lisnyak, M.; Methling, R.; Schoenemann, T.
    The possible use of protective layers made of ceramic powders for walls in thermal plasma applications is studied. A stable free burning arc of currents up to 5 kA between copper- tungsten electrodes is used to analyse the arc interaction with samples coated by mixtures of CaCO3, MgCO3, and Mg(OH)2 with plaster. By means of optical emission spectroscopy the maximum arc temperature and the radiation impact on the surfaces are estimated to be around 15000 K and 20 MWm-2, respectively. Thermographic measurements confirm the efficient protection of substrates by all layer materials. Layers containing CaCO3 lead to the lowest heating of ceramic samples which may be caused by a strong evaporation of the layer material.
  • Thumbnail Image
    Item
    Determination of Cr Density in the Active Phase of a High-current Vacuum Arcs
    (Praha : Czech Technical University in Prague, Faculty of Electrical Engineering, Department of Physics, 2017) Gortschakow, S.; Khakpour, A.; Popov, S.; Franke, S.; Methling, R.; Uhrlandt, D.
    Melting and evaporation of the anode surface strongly influence the interruption capability of vacuum circuit breakers, because they lead to injection of atomic vapour into the inter-electrode gap. Determination of the vapour density and its dynamics with respect to different anode phenomena is therefore of great importance. Results of Cr density measurements in a high-current vacuum arc by using broadband absorption spectroscopy are presented. The vapour density of atomic Cr is determined after the formation of anode spots as well as close to the current zero. Cr I resonance lines at 425.43 nm have been used for the analysis. An AC current pulse with maximum value of 7 kA and a frequency of 100 Hz is applied to a vacuum arc between two cylindrical butt electrodes made of CuCr7525 with a diameter of 10 mm. The high-current anode modes are observed by means of high-speed camera imaging. The temporal evolution of the Cr ground state density is presented and discussed.
  • Thumbnail Image
    Item
    Emission Spectroscopy During High-Current Anode Modes in Vacuum Arc
    (Praha : Czech Technical University in Prague, Faculty of Electrical Engineering, Department of Physics, 2017) Khakpour, A.; Methling, R.; Franke, S.; Gortschakow, S.; Uhrlandt, D.
    A vacuum interrupter reaches its interruption limit once high-current anode phenomena occur. High-current anode modes lead to an increase of the anode surface temperature and an increased generation of metal vapor, which may result in a weakening of the dielectric recovery strength after current zero. In this work, different discharge modes in a vacuum arc for AC 50 Hz including diffuse, footpoint, anode spot type 1 and type 2, and anode plume are investigated. Electrodes made of CuCr7525 with diameter of 10 mm are used. The final gap length is about 20 mm. Time and space resolved optical emission spectroscopy is used to examine the temporal and spatial distribution of atomic and ionic copper lines. The distribution of atomic and ionic lines parallel and perpendicular to the anode surface is investigated. Radiator density is also determined for CuI, CuII, and CuIII near the anode surface.