6 results
Search Results
Now showing 1 - 6 of 6
- ItemMechanical performance and corrosion behaviour of Zr-based bulk metallic glass produced by selective laser melting(Amsterdam : Elsevier B.V., 2020) Deng, L.; Gebert, A.; Zhang, L.; Chen, H.Y.; Gu, D.D.; Kühn, U.; Zimmermann, M.; Kosiba, K.; Pauly, S.Nearly fully dense, glassy Zr52.5Cu17.9Ni14.6Al10Ti5 bulk specimens were fabricated by selective laser melting (SLM) and their behaviour during compressive loading, during wear testing and in a corrosive medium was investigated. Their performance was compared with as-cast material of the same composition. The additively manufactured samples exhibit a yield strength around 1700 MPa combined with a plastic strain of about 0.5% after yielding despite the residual porosity of 1.3%, which is distributed uniformly in the samples. The propagation of shear bands in the bulk metallic glass prepared by SLM was studied. The specific wear rate and the worn surfaces demonstrated that similar wear mechanisms are active in the SLM and the as-cast samples. Hence, manufacturing the glass in layers does not adversely affect the wear properties. The same holds for the corrosion tests, which were carried out in 0.01 M Na2SO4 and 0.1 M NaCl electrolyte. The anodic polarization curves of SLM samples and as-cast samples revealed a similar corrosion behaviour. However, the SLM samples have a slightly reduced susceptibility to pitting corrosion and exhibit an improved surface healing ability, which might be attributed to an improved homogeneity of the additively manufactured glass.
- ItemGuiding shear bands in bulk metallic glasses using stress fields : A perspective from the activation of flow units(Woodbury, NY : Inst., 2020) Kosiba, K.; Scudino, S.; Bednarcik, J.; Bian, J.; Liu, G.; Kühn, U.; Pauly, S.Controlling shear band propagation is the key to obtain ductile metallic glasses. Here, we use a residual stress field to vary the direction of shear band propagation. We ascribe this behavior to the effect of the stress field on the activation of shear transformation zones (STZs) along their characteristic direction and we quantify this contribution to the energy of the process. Because of the progressively adverse orientation of the stress field, the energy stored as shear in the STZ decreases to a level where shear band propagation at alternative angles becomes energetically more favorable. © 2020 authors.
- ItemSerrated flow of CuZr-based bulk metallic glasses probed by nanoindentation: Role of the activation barrier, size and distribution of shear transformation zones(Amsterdam [u.a.] : Elsevier Science, 2017) Limbach, R.; Kosiba, K.; Pauly, S.; Kühn, U.; Wondraczek, L.We report on the effect of Al and Co alloying in vitreous Cu50Zr50 on local deformation and serrated flow as a model for relating the size and localization of shear transformation zones (STZ) to Poisson ratio and strain-rate sensitivity of metallic glasses. Alloying with Al results in significant variations in mechanical performance, in particular, in Young's modulus, hardness and strain-rate sensitivity. Increasing strain-rate sensitivity with increasing degree of alloying indicates a reduced tendency for shear localization. In parallel, a gradual transition from inhomogeneous to homogeneous plastic flow is observed. Using a statistical analysis of the shear stress associated with the initiation of the first pop-in in the load-displacement curve during spherical indentation, the activation volume for plastic flow at the onset of yielding is reported. This analysis is employed for experimental evaluation of the compositional dependence of activation barrier, size and distribution of STZs. It is demonstrated that the STZ size does not change significantly upon Al alloying and encompasses a local volume of around 22–24 atoms. However, the barrier energy density for the initiation of a single STZ progressively increases. The broader distribution of STZs impedes their accumulation into larger-size flow units, leading to a lower number and reduced size of serrations in the load-displacement curve. On the contrary, lower barrier energy densities enable a larger quantity of STZs to be activated simultaneously. These STZs can easily percolate into large flow units, promoting plastic flow through their interaction. We employ Poisson's ratio as an indicator for plasticity to shown that this interpretation can be transferred to other types of metallic glasses. That is, larger flow units were found for metallic glasses with higher Poisson ratio and more pronounced plasticity, while the flow units in alloys with very low Poisson ratio and high brittleness are significantly reduced in size and more homogeneously distributed throughout the material.
- ItemGlass-forming ability, phase formation and mechanical properties of glass-forming Cu-Hf-Zr alloys(Amsterdam : Elsevier B.V., 2019) Kosiba, K.; Song, K.; Kühn, U.; Wang, G.; Pauly, S.The influence of Hf additions on the glass-forming ability (GFA), phase formation and mechanical properties of Cu50HfxZr50-x (x = 2,5,10,20 at.%) alloys has been systematically investigated. We report on a distinct correlation between phase formation and GFA of Cu50Zr50-based alloys. Increasing additions of Hf reduce the thermal stability of the high-temperature B2 Cu(Hf,Zr) phase, while the thermal stability of the corresponding undercooled melt is enhanced. The GFA of these alloy series gradually raises up to 10 at.% Hf, whereas at 20 at.%Hf, the GFA is drastically lowered, since the B2 Cu(Hf,Zr) phase becomes unstable and the precipitation of the low-temperature equilibrium phases is favoured. This interrelation determines the microstructure and results in the formation of Cu-Hf-Zr-based bulk metallic glass composites. These composites not only show appreciable macroscopic plastic strain, but also high yield strength.
- ItemPhase formation of a biocompatible Ti-based alloy under kinetic constraints studied via in-situ high-energy X-ray diffraction(Amsterdam : Elsevier B.V., 2020) Kosiba, K.; Rothkirch, A.; Han, J.; Deng, L.; Escher, B.; Wang, G.; Kühn, U.; Bednarcik, J.The biocompatible Ti40Cu34Pd14Zr10Sn2 bulk metallic glass was rapidly heated, also known as flash-annealed, at varying heating rates up to 1579 K/s. Thereby, the phase formation was characterized via advanced in-situ high-energy X-ray diffraction. It has been found that the evolving kinetic constraints can be used as a tool to deliberately alter the crystalline phase formation. This novel processing route permits to select phases to crystallize to a predefined fraction and, thus, to potentially design the microstructure of materials according to a specified property-profile. Consequently, flash-annealing poses a unique synthesis route to design materials with, for instance, good biomechanical compatibility.
- ItemInductive flash-annealing of bulk metallic glasses(London : Nature Publishing Group, 2017) Kosiba, K.; Pauly, S.We developed a temperature-controlled inductive flash-annealing device, which heats bulk metallic glasses (BMGs) at defined rates of up to 200 K/s to a given temperature. Subsequent instantaneous quenching in water allows preserving the microstructures obtained at various stages of crystallization. One Zr-based and two CuZr-based BMGs were flash-annealed at the onset of crystallization with different heating rates in order to prepare advanced BMG-matrix composites. The highly reproducible composite microstructures contain uniformly dispersed crystals and a narrow crystal size distribution. In order to assess the limitations of the present process, which mainly originate from non-uniform inductive heating, the skin depth was calculated. It is determined to be about 2.3 mm, which enables flash-annealing of rather bulky samples. The cooling rate was estimated from the interlamellar spacing of eutectic Al-Cu alloys to be on the order of 103 K/s. This ensures that decomposition of the microstructure during quenching is prevented. The present flash-annealing procedure is applicable to a wide variety of glass-forming liquids and has a large potential for tailoring the microstructure and, consequently, the mechanical properties of BMG-matrix composites.