Filters

2013 - 2019182020 - 20234

More filters

2021 - 202322
Reset filters

Settings

Author: Pötschke, Petra × DDC: 530 ×

Search Results

Now showing 1 - 10 of 22
  • Thumbnail Image
    Item
    Effect of additives on MWCNT dispersion and electrical percolation in polyamide 12 composites
    (Melville, NY : AIP, 2017) Socher, Robert; Krause, Beate; Pötschke, Petra
    The aim of this study was to decrease the electrical percolation threshold of multiwalled carbon nanotubes (MWCNTs) in a polyamide 12 matrix by the use of additives. Different kinds of additives were selected which either interact with the π-system of the MWCNTs (imidazolium based ionic liquid (IL) and perylene-3,4,9,10-tetracarboxylic dianhydride (PTCDA)) or improve the MWCNT wettability (cyclic butylene terephthalate, CBT). The composites were melt mixed using a DACA microcompounder. The electrical percolation threshold for PA12/MWCNT without additives, measured on compression molded plates, was found between 2.0 and 2.25 wt%. With all used additives, a significant reduction of the electrical percolation threshold could be achieved. Whereas the addition of IL and CBT resulted in MWCNT percolation at around 1.0 wt%, a slightly higher percolation threshold between 1.0 and 1.5 wt% was found for PTCDA as an additive. Interestingly, the electrical resistivity at higher loadings was decreased by nearly two decades when using CBT and one decade after application of PTCDA, whereas IL did not contribute to lower values in this range. In all cases macrodispersion as assessed by light microscopy was not improved and even worse as compared to non-modified composites. In summary, the results illustrate that these kinds of additives are able to improve the performance of PA12 based MWCNT nanocomposites.
  • Thumbnail Image
    Item
    Lightweight polymer-carbon composite current collector for lithium-ion batteries
    (Basel : MDPI, 2020) Fritsch, Marco; Coeler, Matthias; Kunz, Karina; Krause, Beate; Marcinkowski, Peter; Pötschke, Petra; Wolter, Mareike; Michaelis, Alexander
    A hermetic dense polymer-carbon composite-based current collector foil (PCCF) for lithium-ion battery applications was developed and evaluated in comparison to state-of-the-art aluminum (Al) foil collector. Water-processed LiNi0.5Mn1.5O4 (LMNO) cathode and Li4Ti5O12 (LTO) anode coatings with the integration of a thin carbon primer at the interface to the collector were prepared. Despite the fact that the laboratory manufactured PCCF shows a much higher film thickness of 55 µm compared to Al foil of 19 µm, the electrode resistance was measured to be by a factor of 5 lower compared to the Al collector, which was attributed to the low contact resistance between PCCF, carbon primer and electrode microstructure. The PCCF-C-primer collector shows a sufficient voltage stability up to 5 V vs. Li/Li+ and a negligible Li-intercalation loss into the carbon primer. Electrochemical cell tests demonstrate the applicability of the developed PCCF for LMNO and LTO electrodes, with no disadvantage compared to state-of-the-art Al collector. Due to a 50% lower material density, the lightweight and hermetic dense PCCF polymer collector offers the possibility to significantly decrease the mass loading of the collector in battery cells, which can be of special interest for bipolar battery architectures. © 2020 by the authors. Licensee MDPI, Basel, Switzerland.
  • Thumbnail Image
    Item
    Development of joining methods for highly filled Graphite/PP composite based bipolar plates for fuel cells: Adhesive joining and welding
    (Melville, NY : AIP, 2019) Rzeczkowski, P.; Lucia, M.; Müller, A.; Facklam, M.; Cohnen, A.; Schäfer, P.; Hopmann, C.; Hickmann, T.; Pötschke, Petra; Krause, Beate
    Novel material solutions for bipolar plates in fuel cells require adapted ways of joining and sealing technologies. Safe and life time enduring leak-tight contacts must be achieved by automatic processes using reasonable joint forces. A proper sealing should manage such challenges as good ageing properties, excellent leaktightness, high thermal conductivity and low gas permeability. Hence in this work, adhesive bonding and welding are considered as suitable methods, which can fulfill the requirements mentioned above. Adhesive systems seem to be more easy to apply than conventional sealing (hand layed-up rubber gaskets), e.g. with automatic dispensers. Additionally, the properties of an adhesive joint can be enhanced by a process-specific surface pre-treatment. This work focuses on the characterization of adhesive systems and their joints with highly filled graphite composites. Mechanical properties of the joints were characterized through lap-shear tests. The influence of ageing caused by humidity or acidic solvent at increased temperature on the bond line properties as well as neat adhesive was examined. The thermal conductivities of neat adhesives and through the entire joint were examined. In order to improve above conductivities, roughening, substrate pre-heating, post-curing and various contact pressure weights were applied. Plasma treatment was chosen as surface pre-treatment method for improving substrate's surface energy. An alternative to bonding is plastic welding, which does not require the use of sealants and adhesives. Based on former study of influences of filler content on the welding process using ultrasonic, hot plate or infrared welding, a welding method for joining the graphite compounds was derived.
  • Thumbnail Image
    Item
    Influence of graphite and SEBS addition on thermal and electrical conductivity and mechanical properties of polypropylene composites
    (Melville, NY : AIP, 2017) Krause, Beate; Cohnen, A.; Pötschke, Petra; Hickmann, T.; Koppler, D.; Proksch, B.; Kersting, T.; Hopmann, C.
    In this study, composites based on polypropylene (PP) and different graphite fillers were melt mixed using small scale microcompounder Xplore DSM15 as well as lab-scale co-rotating twin screw extruder Coperion ZSK26Mc. The measurements of the electrical and thermal conductivity as well as mechanical properties of the composites were performed on pressed plates. It was found that the addition of graphite powders having different particle size distributions leads to different increases of the thermal conductivity. For synthetic graphite, the PP composites filled with TIMCAL Timrex® KS500 reached the highest value of thermal conductivity of 0.52 W/(m·K) at 10 vol% loading, whereas this composite was not electrical conductive. Furthermore, the influence of a styrene-ethylene-butylene-styrene block copolymer (SEBS) based impact modifier on the mechanical properties of PP filled with 80 wt% of different synthetic graphites was investigated. For that the proportion of SEBS in the PP component was varied systematically. The conductivities were influenced by the type of graphite and the content of impact modifier. The results indicate that the impact strength of the composite containing TIMCAL Timrex® KS300-1250 can be increased by approx. 100 % when replacing 50 wt% of the PP component by SEBS.
  • Thumbnail Image
    Item
    Experimental and computational analysis of thermoelectric modules based on melt-mixed polypropylene composites
    (Amsterdam : Elsevier, 2023) Doraghi, Qusay; Żabnieńska-Góra, Alina; Norman, Les; Krause, Beate; Pötschke, Petra; Jouhara, Hussam
    Researchers are constantly looking for new materials that exploit the Seebeck phenomenon to convert heat into electrical energy using thermoelectric generators (TEGs). New lead-free thermoelectric materials are being investigated as part of the EU project InComEss, with one of the anticipated uses being converting wasted heat into electric energy. Such research aims to reduce the production costs as well as the environmental impact of current TEG modules which mostly employ bismuth for their construction. The use of polymers that, despite lower efficiency, achieve increasingly higher values of electrical conductivity and Seebeck coefficients at a low heat transfer coefficient is increasingly discussed in the literature. This article presents two thermoelectric generator (TEG) models based on data previously described in the literature. Two types of designs are presented: consisting of 4- and 49-leg pairs of p- and n-type composites based on polypropylene melt-mixed with single-walled carbon nanotubes. The models being developed using COMSOL Multiphysics software and validated based on measurements carried out in the laboratory. Based on the results of the analysis, conductive polymer composites employing insulating matrices can be considered as a promising material of the future for TEG modules.
  • Thumbnail Image
    Item
    Aspect ratio effects of multi-walled carbon nanotubes on electrical, mechanical, and thermal properties of polycarbonate/MWCNT composites
    (Hoboken, NJ [u.a.] : Wiley, 2014) Guo, Jiaxi; Liu, Yanjun; Prada-Silvy, Ricardo; Tan, Yongqiang; Azad, Samina; Krause, Beate; Pötschke, Petra; Grady, Brian P.
    Two multi-walled carbon nanotubes (MWCNTs) having relatively high aspect ratios of 313 and 474 with approximately the same diameter were melt mixed with polycarbonate (PC) in a twin-screw conical micro compounder. The effects of aspect ratio on the electrical, mechanical, and thermal properties of the PC/MWCNT composites were investigated. Electrical conductivities and storage moduli of the filled samples are found to be independent of the starting aspect ratio for these high aspect ratio tubes; although the conductivities and storage moduli are still significantly higher than values of composites made with nanotubes having more commercially common aspect ratios of ∼100. Transmission electron microscopy results suggest that melt-mixing reduces these longer nanotubes to the same length, but still approximately two times longer than the length of commercially common aspect ratio tubes after melt-mixing. Molecular weight measurements show that during melt-mixing the longer nanotubes significantly degrade the molecular weight of the polymer as compared to very similar nanotubes with aspect ratio ∼100. Because of the molecular weight reduction glass transition temperatures predictably show a large decrease with increasing nanotube concentration. © 2013 Wiley Periodicals, Inc.
  • Thumbnail Image
    Item
    Electrical and thermal conductivity of polypropylene filled with combinations of carbon fillers
    (Melville, NY : AIP, 2016) Krause, Beate; Pötschke, Petra
    The thermal and electrical conductivity of polymer composites filled with a low content up to 7.5 vol% of different carbon fillers (carbon nanotubes, carbon fibers, graphite nanoplates) were investigated. It was found that the combination of two or three carbon fillers leads to an increase of thermal conductivity up to 193% which is higher than the sum of the effects of both fillers.
  • Thumbnail Image
    Item
    Graphite modified epoxy-based adhesive for joining of aluminium and PP/graphite composites
    (New York, NY [u.a.] : Taylor & Francis, 2020) Rzeczkowski, P.; Pötschke, Petra; Fischer, M.; Kühnert, I.; Krause, Beate
    A graphite-modified adhesive was developed in order to simultaneously enhance the thermal conductivity and the strength of an adhesive joint. The thermal conductivity through the joint was investigated by using highly filled PP/graphite composite substrates, which were joined with an epoxy adhesive of different layer thicknesses. Similar measurements were carried out with a constant adhesive layer thickness, whilst applying an epoxy adhesive modified with expanded graphite (EG) (6, 10, and 20 wt%). By reducing the adhesive layer thickness or modifying the adhesive with conductive fillers, a significant increase of the thermal conductivity through the joint was achieved. The examination of the mechanical properties of the modified adhesives was carried out by tensile tests (adhesive only), lap-shear tests, and fracture energy tests (mode 1) with aluminium substrates. Modification of the adhesive with EG led to an increase of the tensile lap-shear strength and the adhesive fracture energy (mode 1) of the joint. In addition, burst pressure tests were performed to determine the strength of the joint in a complex component. The strength of the joint increased with the graphite content in the PP substrate and in the epoxy adhesive.
  • Thumbnail Image
    Item
    Influence of talc with different particle sizes in melt-mixed LLDPE/MWCNT composites
    (Hoboken, NJ [u.a.] : Wiley, 2013) Müller, Michael Thomas; Dreyße, Janine; Häußler, Liane; Krause, Beate; Pötschke, Petra
    Linear low-density polyethylene (LLDPE) was melt-mixed with multiwalled carbon nanotubes (MWCNTs) and varying amounts of three different kinds of talc (phyllo silicate), each with a different particle size distribution, to examine the effect of these filler combinations with regards to the electrical percolation behavior. The state of the filler dispersion was assessed using transmission light microscopy and electron microscopy. The use of talc as a second filler during the melt mixing of LLDPE/MWCNT composites resulted in an improvement in the dispersion of the MWCNTs and a decrease of the electrical percolation threshold. Talc with lower particle sizes showed a more pronounced effect than talc with larger particle sizes. However, the improvement in dispersion was not reflected in the mechanical properties. Modulus and stress values increase with both, MWCNT and talc addition, but not in a synergistic manner. The crystallization behavior of the composites was studied by differential scanning calorimetry to determine its potential influence on the electrical percolation threshold. It was found that the crystallinity of the matrix increased slightly with the addition of talc but no further increments were observed with the incorporation of the MWCNTs. © 2013 Wiley Periodicals, Inc.
  • Thumbnail Image
    Item
    PP/SWCNT composites modified with ionic liquid
    (Melville, NY : AIP, 2017) Krause, Beate; Predtechenskiy, M.; Ilin, E.; Pötschke, Petra
    Polypropylene composites filled with singlewalled carbon nanotubes TUBALL® (SWCNTs) were studied with regard to the effect of ionic liquid (IL) addition in different SWCNT:IL ratios (1:0.5 - 1:6). The incorporation of IL leads to a decrease of the electrical percolation threshold and already at 0.025 wt% SWCNT loading reduced resistivity values can be observed. However, the SWCNT macro dispersion, already relatively good without IL, was not affected by the IL incorporation. In addition, the nucleation effect of the SWCNT in polypropylene is not influenced when simultaneously adding IL, whereas the crystallization enthalpy slightly decreases with its addition.