12 results
Search Results
Now showing 1 - 10 of 12
- ItemCohesive detachment of an elastic pillar from a dissimilar substrate(Amsterdam : Elsevier, 2017) Fleck, Norman A.; Khaderi, Syed Nizamuddin; McMeeking, Robert M.; Arzt, EduardThe adhesion of micron-scale surfaces due to intermolecular interactions is a subject of in- tense interest spanning electronics, biomechanics and the application of soft materials to engineering devices. The degree of adhesion is sensitive to the diameter of micro-pillars in addition to the degree of elastic mismatch between pillar and substrate. Adhesion- strength-controlled detachment of an elastic circular cylinder from a dissimilar substrate is predicted using a Dugdale-type of analysis, with a cohesive zone of uniform tensile strength emanating from the interface corner. Detachment initiates when the opening of the cohesive zone attains a critical value, giving way to crack formation. When the cohe- sive zone size at crack initiation is small compared to the pillar diameter, the initiation of detachment can be expressed in terms of a critical value H c of the corner stress inten- sity. The estimated pull-offforce is somewhat sensitive to the choice of stick/slip boundary condition used on the cohesive zone, especially when the substrate material is much stiffer than the pillar material. The analysis can be used to predict the sensitivity of detachment force to the size of pillar and to the degree of elastic mismatch between pillar and sub- strate.
- ItemOn the process of co-deformation and phase dissolution in a hard-soft immiscible CuCo alloy system during high-pressure torsion deformation(Amsterdam : Elsevier, 2016) Bachmaier, Andrea; Schmauch, Jörg; Aboulfadl, Hisham; Verch, Andreas; Motz, ChristianIn this study, dual phase Cusingle bondCo composites with a total immiscibility in the solid state and a very different initial phase strength are deformed by severe plastic deformation. Nanocrystalline supersaturated solid solutions are reached in all Cusingle bondCo composites independent of the initial composition. The deformation and mechanical mixing process is studied thoroughly by combining scanning electron microscopy, transmission electron microscopy, three-dimensional atom probe tomography and nanoindentation. The indentation hardness of the Cu and Co phase and its evolution as a function of the applied strain is linked to deformation and mechanical mixing process to gain a better understanding how the phase strength mismatch of the Cu and Co phase effects the amount of co-deformation and deformation-induced mixing. Our results show that co-deformation is not a necessary requirement to achieve mechanical mixing.
- ItemUltrathin gold nanowires for transparent electronics: breaking barriers(Amsterdam : Elsevier, 2016) Gonzalez-Garcia, Lola; Maurer, Johannes H.M.; Reiser, Beate; Kanelidis, Ioannis; Kraus, TobiasNovel types of Transparent Conductive Materials (TCMs) based on metal nanostructures are discussed. Dispersed metal nanoparticles can be deposited from liquids with moderate thermal budgets to form conductive films that are suitable for thin-film solar cells, displays, touch screens, and nanoelectronics. We aim at new TCMs that combine high electrical conductivity with optical transparency and mechanical flexibility. Wet-processed films of randomly arranged metallic nanowires networks are commercially established and provide a relatively cost-effective, scalable production. Ultrathin gold nanowires (AuNWs) with diameters below 2 nm and high aspect ratios have recently become available. They combine mechanical flexibility, high optical transparency, and chemical inertness. AuNWs carry oleylamine capping ligands from synthesis that cause high contact resistances at their junctions. We investigated different annealing processes based on temperature and plasma treatment, to remove the ligands after deposition and to allow electrical conductivity. Their effect on the resulting nanostructure and on the material properties was studied. Scanning Electron Microscopy (SEM) and optical spectroscopy revealed changes in the microstructure for the different post-treatments. We found that the conductivity and the stability of the TCM depended strongly on its final microstructure. We demonstrate that the best results are obtained using H2-plasma treatment.
- ItemThe potential of fractional diagonal chromatography strategies for the enrichment of post-translational modifications(Amsterdam : Elsevier, 2014) Venne, A. Saskia; Zahedi, René P.More than 450 post-translational modifications (PTMs) are known, however, currently only some of those can be enriched and analyzed from complex samples such as cell lysates. Therefore, we need additional methods and concepts to improve our understanding about the dynamic crosstalk of PTMs and the highly context-dependent regulation of protein function by so-called ‘PTM codes’. The mere focus on affinity-based enrichment techniques may not be sufficient to achieve this ambitious goal. However, the complementary use of two-dimensional chromatography-based strategies such as COFRADIC and ChaFRADIC might open new avenues for enriching a variety of so far inaccessible PTMs for large-scale proteome studies.
- ItemElectrospinning and electrospraying of silicon oxycarbide-derived nanoporous carbon for supercapacitor electrodes(Amsterdam : Elsevier, 2016) Tolosa, Aura; Krüner, Benjamin; Jäckel, Nicolas; Aslan, Mesut; Vakifahmetoglu, Cekdar; Presser, VolkerIn this study, carbide-derived carbon fibers from silicon oxycarbide precursor were synthesized by electrospinning of a commercially available silicone resin without adding a carrier polymer for the electrospinning process. The electrospun fibers were pyrolyzed yielding SiOC. Modifying the synthesis procedure, we were able to obtain electrosprayed SiOC beads instead of fibers. After chlorine treatment, nanoporous carbon with a specific surface area of up to 2394 m2·g-1 was obtained (3089 m2·g-1 BET). Electrochemical characterization of the SiOC-CDC either as free-standing fiber mat electrodes or polymer-bound bead films was performed in 1 M tetraethylammonium tetrafluoroborate in acetonitrile (TEA-BF4 in ACN). The electrospun fibers presented a high gravimetric capacitance of 135 F·g-1 at 10 mV·s-1 and a very high power handling, maintaining 63 % of the capacitance at 100 A·g-1. Comparative data of SiOC-CDC beads and fibers show enhanced power handling for fiber mats only when the fiber network is intact, that is, a lowered performance was observed when using crushed mats that employ polymer binder.
- ItemNumerical study of adhesion enhancement by composite fibrils with soft tip layers(Amsterdam : Elsevier, 2016) Balijepalli, Ram Gopal; Fischer, Sarah C.L.; Hensel, René; McMeeking, Robert M.; Arzt, EduardBio-inspired fibrillar surfaces with reversible adhesion to stiff substrates have been thoroughly investigated over the last decade. In this paper we propose a novel composite fibril consisting of a soft tip layer and stiffer stalk with differently shaped interfaces (flat vs. curved) between them. A tensile stress is applied remotely on the free end of the fibril whose other end adheres to a rigid substrate. The stress distributions and the resulting adhesion of such structures were numerically investigated under plane strain (2D) and axisymmetric (3D) conditions. The stress intensities were evaluated for different combinations of layer thickness and Young’s moduli. The adhesion strength values were found to increase for thinner layers and larger modulus ratio; these trends are also reflected in selected experimental results. The results of this paper provide a new strategy for optimizing adhesion strength of fibrillar surfaces.
- ItemVacuum or flowing argon: What is the best synthesis atmosphere for nanodiamond-derived carbon onions for supercapacitor electrodes?(Amsterdam : Elsevier, 2015) Zeiger, Marco; Jäckel, Nicolas; Weingarth, Daniel; Presser, VolkerWe present a comprehensive study on the influence of the synthesis atmosphere on the structure and properties of nanodiamond-derived carbon onions. Carbon onions were synthesized at 1300 and 1700 °C in high vacuum or argon flow, using rapid dynamic heating and cooling. High vacuum annealing yielded carbon onions with nearly perfect spherical shape. An increase in surface area was caused by a decrease in particle density when transitioning from sp3 to sp2 hybridization and negligible amounts of disordered carbon were produced. In contrast, carbon onions from annealing nanodiamonds in flowing argon are highly interconnected by few-layer graphene nanoribbons. The presence of the latter improves the electrical conductivity, which is reflected by an enhanced power handling ability of supercapacitor electrodes operated in an organic electrolyte (1 M tetraethylammonium tetrafluoroborate in acetonitrile). Carbon onions synthesized in argon flow at 1700 °C show a specific capacitance of 20 F/g at 20 A/g current density and 2.7 V cell voltage which is an improvement of more than 40% compared to vacuum annealing. The same effect was measured for a synthesis temperature of 1300 °C, with a 140% higher capacitance at 20 A/g for argon flow compared to vacuum annealing.
- ItemReview on the science and technology of water desalination by capacitive deionization(Amsterdam : Elsevier, 2013) Presser, Volker; Porada, S.; Zhao, R.; van der Wal, A.; Biesheuvel, P.M.Porous carbon electrodes have significant potential for energy-efficient water desalination using a promising technology called Capacitive Deionization (CDI). In CDI, salt ions are removed from brackish water upon applying an electrical voltage difference between two porous electrodes, in which the ions will be temporarily immobilized. These electrodes are made of porous carbons optimized for salt storage capacity and ion and electron transport. We review the science and technology of CDI and describe the range of possible electrode materials and the various approaches to the testing of materials and devices. We summarize the range of options for CDI-designs and possible operational modes, and describe the various theoretical–conceptual approaches to understand the phenomenon of CDI.
- ItemElevated temperature adhesion of bioinspired polymeric micropatterns to glass(Amsterdam : Elsevier, 2017) Barreau, Viktoriia; Yu, Dan; Hensel, René; Arzt, EduardMicropatterned polymer surfaces that operate at various temperatures are required for emerging technical applications such as handling of objects or space debris. As the mechanical properties of polymers can vary significantly with temperature, adhesion performance can exhibit large variability. In the present paper, we experimentally study temperature effects on the adhesion of micropatterned adhesives (pillar length 20 μm, aspect ratios 0.4 and 2) made from three different polymers, i.e., polydimethylsiloxane (PDMS), perfluoropolyether dimethacrylate (PFPEdma), and polyurethane (PU-ht). PU specimens showed the highest pull-off stresses of about 57 kPa at 60 °C, i.e., more than twice the value of unpatterned control samples. The work of separation similarly showed a maximum at that temperature, which was identified as the glass transition temperature, Tg. PDMS and PFPEdma specimens were tested above their Tg. As a result, the adhesion properties decreased monotonically (about 50% for both materials) for temperature elevation from 20 to 120 °C. Overall, the results obtained in our study indicate that the operating temperature related to the glass transition temperature should be considered as a significant parameter for assessing the adhesion performance of micropatterned adhesives and in the technical design of adhesion devices.
- ItemAdhesion and relaxation of a soft elastomer on surfaces with skin like roughness(Amsterdam : Elsevier, 2018) Fischer, Sarah; Boyadzhieva, Silviya; Hensel, René; Kruttwig, Klaus; Arzt, EduardFor designing new skin adhesives, the complex mechanical interaction of soft elastomers with surfaces of various roughnesses needs to be better understood. We systematically studied the effects of a wide set of roughnesscharacteristics, film thickness, hold time and material relaxation on the adhesive behaviour of the silicone elastomer SSA 7–9800 (Dow Corning). As model surfaces, we used epoxy replicas obtained from substrates with roughness ranging from very smooth to skin-like. Our results demonstrate that films of thin and intermediate thickness (60 and 160 μm) adhered best to a sub-micron rough surface, with a pull-off stress of about 50 kPa. Significant variations in pull-off stress and detachment mechanism with roughness and hold time were found. In contrast, 320 μm thick films adhered with lower pull-off stress of about 17 kPa, but were less sensitive to roughness and hold time. It is demonstrated that the adhesion performance of the siliconefilms to rough surfaces can be tuned by tailoring the film thickness and contact time.