23 results
Search Results
Now showing 1 - 10 of 23
- ItemRare-earth-free MnAl-C-Ni permanent magnets produced by extrusion of powder milled from bulk(Amsterdam : Elsevier, 2020) Feng, Le; Freudenberger, Jens; Mix, Torsten; Nielsch, Kornelius; Woodcock, Thomas GeorgeRare-earth-free MnAl-C-Ni permanent magnets have been produced for the first time by extruding powders milled from bulk. The resulting materials, fabricated using different conditions, contained a large volume fraction (> 0.92) of the desired τ-phase. In terms of the maximum energy product, the best performance obtained for a whole, transverse section of the extruded material was (BH)max = 46 kJm−3, and was (BH)max = 49 kJm−3 for a sample taken from near the edge of this section. Analysis showed that this material was comparable to the long-established benchmark, comprising MnAl-C-based magnets extruded in industry from bulk or from gas-atomised powder. Such materials are no longer available. The microstructure of the materials produced here consisted of fine, recrystallised grains, which exhibited an <001> fibre texture with intermediate texture quality and of larger, non-recrystallised regions, which contained hierarchical twinning and a high density of defects. The volume fraction and size of the non-recrystallised regions was greatly reduced by decreasing the size of the initial powder particles. This led to a large increase in the squareness factor of the demagnetisation curve and consequently to the high (BH)max values observed.
- ItemReversibly compressible and freestanding monolithic carbon spherogels(Amsterdam : Elsevier, 2019) Salihovic, M.; Zickler, G.A.; Fritz-Popovski, G.; Ulbricht, M.; Paris, O.; Hüsing, N.; Presser, V.; Elsaesser, M.S.We present a versatile strategy to tailor the nanostructure of monolithic carbon aerogels. By use of an aqueous colloidal solution of polystyrene in the sol-gel processing of resorcinol-formaldehyde gels, we can prepare, after supercritical drying and successive carbonization, freestanding monolithic carbon aerogels, solely composed of interconnected and uniformly sized hollow spheres, which we name carbon spherogels. Each sphere is enclosed by a microporous carbon wall whose thickness can be adjusted by the polystyrene concentration, which affects the pore texture as well as the mechanical properties of the aerogel monolith. In this study, we used monodisperse polystyrene spheres of approximately 250 nm diameter, which result in an inner diameter of the final hollow carbon spheres of approximately 200 ± 5 nm due to shrinkage during the carbonization process. The excellent homogeneity of the samples, as well as uniform sphere geometries, are confirmed by small- and angle X-ray scattering. The presence of macropores between the hollow spheres creates a monolithic network with the benefit of being reversibly compressible up to 10% linear strain without destruction. Electrochemical tests demonstrate the applicability of ground and CO2 activated carbon spherogels as electrode materials. © 2019 The Authors
- ItemMembrane Tension Orchestrates Rear Retraction in Matrix-Directed Cell Migration(Amsterdam : Elsevier, 2019) Hetmanski, J.H.R.; de, Belly, H.; Busnelli, I.; Waring, T.; Nair, R.V.; Sokleva, V.; Dobre, O.; Cameron, A.; Gauthier, N.; Lamaze, C.; Swift, J.; del, Campo, A.; Starborg, T.; Zech, T.; Goetz, J.G.; Paluch, E.K.; Schwartz, J.-M.; Caswell, P.T.In development, wound healing, and cancer metastasis, vertebrate cells move through 3D interstitial matrix, responding to chemical and physical guidance cues. Protrusion at the cell front has been extensively studied, but the retraction phase of the migration cycle is not well understood. Here, we show that fast-moving cells guided by matrix cues establish positive feedback control of rear retraction by sensing membrane tension. We reveal a mechanism of rear retraction in 3D matrix and durotaxis controlled by caveolae, which form in response to low membrane tension at the cell rear. Caveolae activate RhoA-ROCK1/PKN2 signaling via the RhoA guanidine nucleotide exchange factor (GEF) Ect2 to control local F-actin organization and contractility in this subcellular region and promote translocation of the cell rear. A positive feedback loop between cytoskeletal signaling and membrane tension leads to rapid retraction to complete the migration cycle in fast-moving cells, providing directional memory to drive persistent cell migration in complex matrices. © 2019 The AuthorsCell migration through 3D matrix is critical to developmental and disease processes, but the mechanisms that control rear retraction are poorly understood. Hetmanski et al. show that differential membrane tension allows caveolae to form at the rear of migrating cells and activate the contractile actin cytoskeleton to promote rapid retraction. © 2019 The Authors
- ItemNano energy for miniaturized systems(Amsterdam : Elsevier, 2021) Zhu, Minshen; Zhu, Feng; Schmidt, Oliver G.Skin mountable electronic devices are in a high-speed development at the crossroads of materials science, electronics, and computer science. Sophisticated functions, such as sensing, actuating, and computing, are integrated into a soft electronic device that can be firmly mounted to any place of human body. These advanced electronic devices are capable of yielding abilities for us whenever they are needed and even expanding our abilities beyond their natural limitations. Despite the great promise of skin mounted electronic devices, they still lack satisfactory power supplies that are safe and continuous. This Perspective discusses the prospects of the development of energy storage devices for the next generation skin mountable electronic devices based on their unique requirements on flexibility and miniaturized size.
- ItemSwitchable double-sided micropatterned adhesives for selective fixation and detachment(Amsterdam : Elsevier, 2019) Tinnemann, V.; Arzt, E.; Hensel, R.Micropatterned dry adhesives are promising candidates for the development of innovative adhesive platforms. Their reversible adhesion to various materials and surfaces has been reported over more than a decade. Switching between a strong and a weak adhesive state can be introduced by elastic buckling instabilities of the microstructure. In this work, we report on novel adhesive pads that exhibit micropatterned pillars on both sides. In double-sided PDMS micropatterns, the dimensions of the pillar structures were tuned by modulating the critical force for buckling during compressive loading. In this way, selective detachment of glass substrates was induced from one side of the pad. Our results indicate a significant switching efficiency of up to 83% between the strong and weak adhesive state. The new structures have high potential for emerging applications where temporary, double-sided fixations in combination with a predetermined detachment location are required. © 2018
- ItemThe influence of mean strain on the high-cycle fatigue of Nitinol with application to medical devices(Amsterdam : Elsevier, 2020) Cao, H.; Wu, M.H.; Zhou, F.; McMeeking, R.M.; Ritchie, R.O.One of the contentious issues associated with the high-cycle fatigue of Nitinol, a nominally equiatomic alloy of nickel and titanium, is the claim that increasing the applied mean strain can increase, or at least have no negative impact, on the fatigue lifetime, in conflict with reported behavior for the vast majority of other metallic materials. To investigate this in further detail, cyclic fatigue tests in bending were carried out on electropolished medical grade Nitinol at 37 °C for lives of up to 400 million cycles of strain involving various levels of the mean strain. A constant life model was developed through statistical analysis of the fatigue data, with 90% reliability at a confidence level of 95% on the effective fatigue strain. Our results show that the constant life diagram, a plot of strain amplitude versus mean strain, is monotonic yet nonlinear for lives of 400 million cycles of fatigue loading. Specifically, we find that in contradiction to the aforementioned claim, the strain amplitude limit at zero mean strain is 0.55% to achieve a 400 million cycle lifetime, at 90% reliability with 95% confidence; however, to achieve the same lifetime, reliability and confidence level in the presence of a 3% or more mean strain, the required strain amplitude limit is decreased by over a factor of three to 0.16%. Moreover, for mean strains from 3% to 7%, the strain amplitude limit that allows a 400 million cycle lifetime, at 90% reliability with 95% confidence, is ~ 0.16%, and essentially independent of mean strain. We conclude that the debatable claim that an increase in the applied mean strain can increase the fatigue life of Nitinol components is not supported by the current data.
- ItemDetermination of fluoride component in the multifunctional refining flux used for recycling aluminum scrap(Amsterdam : Elsevier, 2020) Wan, Bingbing; Li, Wenfang; Liu, Fangfang; Lu, Tiwen; Jin, Shuoxun; Wang, Kang; Yi, Aihua; Tian, Jun; Chen, WeipingIn this paper, the optimum fluoride component in the multifunctional refining flux used for recycling aluminum scrap was determined. Theoretical analysis of solid fluxing shows that strong stripping ability of oxide layer on aluminum surface for the flux and appropriate interfacial tensions between Al melt / inclusion (σM-I), flux / inclusion (σF-I), and flux / Al melt (σF-M) are indispensable for making the flux achieve the properties of covering, drossing, and cleaning simultaneously. In term of four preliminarily selected fluoride salts, i.e., KF, AlF3, K3AlF6 and KAlF4, the results of interfacial tension measurements indicates that, combined addition of A-type fluoride (KF) and B-type fluoride (AlF3, K3AlF6 and KAlF4) to equimolar NaCl-KCl can just offset the shortage of single addition of KF which means worsening the separating effect of flux from melt surface and weakening the wettability of flux on the inclusions due to the lower σF-M and the higher σF-I respectively. Additionally, coalescence behaviors of aluminum droplets in molten fluxes reveals that, KF, K3AlF6 or KAlF4 possesses stronger stripping ability of oxide layer, while the stripping ability of oxide layer for AlF3 is weaker. Ultimately, the combination of KF with K3AlF6 or/and KAlF4 is ascertained to be an optimum selection for fluoride component in the multifunctional refining flux.
- ItemMicrostructure, mechanical properties and machinability of particulate reinforced Al matrix composites: a comparative study between SiC particles and high-entropy alloy particles(Amsterdam : Elsevier, 2020) Lu, Tiwen; He, Tianbing; Li, Zixuan; Chen, Hongyu; Han, Xiaoliang; Fu, Zhiqiang; Chen, WeipingIn this study, 2024Al matrix composites reinforced by SiC particles (SiC-2024Al) and nanocrystalline high-entropy alloy particles (HEA-2024Al) fabricated by powder metallurgy were systematically compared for the first time. There is a significant difference in microstructure and mechanical properties as well as machinability between two kinds of composites. In term of microstructure, when the volume fraction of reinforcements was 10%, both SiC-2024Al and HEA-2024Al composites showed a homogeneous particle distribution in the matrix. With the increase of reinforcement content, HEA-2024Al composites presented denser microstructure than that of SiC-2024Al composites. The composites with 10, 20 and 30 vol.% HEA reinforcements all showed better plasticity than that of the SiC-2024Al composites with same volume fraction of reinforcements, which was related with better particle distribution and interface bonding. However, the strength showed the opposite tendency in the two kinds of composites. Selecting 10SiC-2024Al and 10HEA-2024Al composites as examples to explore the difference in the yield strength of two kinds of composites, it is ascribed to the dislocation punched zones around interface between the Al matrix and reinforcements, which was analyzed in detail by a combination of calculation, nanoindentation tests and finite element analysis. Additionally, HEA-2024Al composites showed better machinability than those of SiC-2024Al composites. This work provides insight into the application of particulate reinforced Al matrix composites.
- ItemUnderstanding of water resilience in the Anthropocene(Amsterdam : Elsevier, 2019) Falkenmark, Malin; Wang-Erlandsson, Lan; Rockström, JohanWater is indispensable for Earth resilience and sustainable development. The capacity of social-ecological systems to deal with shocks, adapting to changing conditions and transforming in situations of crisis are fundamentally dependent on the functions of water to e.g., regulate the Earth's climate, support biomass production, and supply water resources for human societies. However, massive, inter-connected, human interference involving climate forcing, water withdrawal, dam constructions, and land-use change have significantly disturbed these water functions and induced regime shifts in social-ecological systems. In many cases, changes in core water functions have pushed systems beyond tipping points and led to fundamental shifts in system feedback. Examples of such transgressions, where water has played a critical role, are collapse of aquatic systems beyond water quality and quantity thresholds, desertification due to soil and ecosystem degradation, and tropical forest dieback associated with self-amplifying moisture and carbon feedbacks. Here, we aggregate the volumes and flows of water involved in water functions globally, and review the evidence of freshwater related linear collapse and non-linear tipping points in ecological and social systems through the lens of resilience theory. Based on the literature review, we synthesize the role of water in mediating different types of ecosystem regime shifts, and generalize the process by which life support systems are at risk of collapsing due to loss of water functions. We conclude that water plays a fundamental role in providing social-ecological resilience, and suggest that further research is needed to understand how the erosion of water resilience at local and regional scale may potentially interact, cascade, or amplify through the complex, globally hyper-connected networks of the Anthropocene. © 2018 The Authors
- ItemOpinion paper : Measuring livestock robustness and resilience : are we on the right track?(Amsterdam : Elsevier, 2019) Llonch, P.; Hoffmann, G.; Bodas, R.; Mirbach, D.; Verwer, C.; Haskell, M.J.[No abstract available]