14 results
Search Results
Now showing 1 - 10 of 14
- ItemPolymeric monolithic materials: Syntheses, properties, functionalization and applications(Amsterdam : Elsevier, 2007) Buchmeiser, M.R.The synthetic particularities for the synthesis of polymer-based monolithic materials are summarized. In this context, monoliths prepared via thermal-, UV- or electron-beam triggered free radical polymerization, controlled TEMPO-mediated radical polymerization, polyaddition, polycondensation as well as living ring-opening metathesis polymerization (ROMP) will be covered. Particular attention is devoted to the aspects of controlling pore sizes, pore volumes and pore size distributions as well as functionalization of these supports. Finally, selected, recent applications in separation science, (bio-) catalysis and chip technology will be summarized. © 2007 Elsevier Ltd. All rights reserved.
- ItemInvestigation of changes in crystalline and amorphous structure during deformation of nano-reinforced semi-crystalline polymers by space-resolved synchrotron saxs and waxs(Amsterdam : Elsevier, 2009) Schneider, K.; Schone, A.; Jun, T.-S.; Korsunsky, A.M.Complex structural changes occur in semi-crystalline polymers during deformation. In (nano-)filled systems the situation becomes even more complicated, since not only phase changes may take place, but also local (interfacial) failure between phases may occur. To help identify specific processes taking place within these systems, simultaneous small- and wide-angle X-ray scattering (SAXS/WAXS) measurements were performed using synchrotron radiation during in situ deformation. Using a highly focused beam, spatially resolved local information can be extracted by scanning the beam across the deformed/damaged region within the sample. The characteristic changes in the different phases are presented and discussed. While the study of WAXS patterns gives insight into the orientation and dimensions of the crystallites, SAXS provides information about the mutual arrangement of phases and the interfacial failure phenomena. Based on the analysis of the results obtained in our experiments it will be shown that the first changes in the crystalline phase appear long before macroscopic yielding of the sample is reached, i.e. the onset of irreversible deformation takes place. In the post-yield regime radical changes are observed in both the long- and short-range structures. It is concluded that the presence of nano-fillers exerts a strong influence on the establishment of microcrystalline structure, and hence also on the deformation behaviour at the microscopic scale.
- ItemExperimental and computational analysis of thermoelectric modules based on melt-mixed polypropylene composites(Amsterdam : Elsevier, 2023) Doraghi, Qusay; Żabnieńska-Góra, Alina; Norman, Les; Krause, Beate; Pötschke, Petra; Jouhara, HussamResearchers are constantly looking for new materials that exploit the Seebeck phenomenon to convert heat into electrical energy using thermoelectric generators (TEGs). New lead-free thermoelectric materials are being investigated as part of the EU project InComEss, with one of the anticipated uses being converting wasted heat into electric energy. Such research aims to reduce the production costs as well as the environmental impact of current TEG modules which mostly employ bismuth for their construction. The use of polymers that, despite lower efficiency, achieve increasingly higher values of electrical conductivity and Seebeck coefficients at a low heat transfer coefficient is increasingly discussed in the literature. This article presents two thermoelectric generator (TEG) models based on data previously described in the literature. Two types of designs are presented: consisting of 4- and 49-leg pairs of p- and n-type composites based on polypropylene melt-mixed with single-walled carbon nanotubes. The models being developed using COMSOL Multiphysics software and validated based on measurements carried out in the laboratory. Based on the results of the analysis, conductive polymer composites employing insulating matrices can be considered as a promising material of the future for TEG modules.
- ItemMicro-embossing of micro-structures in RSA-501 as mold inserts for the replication of micro-lens arrays(Amsterdam : Elsevier, 2022) Kober, Julian; Rolón, Daniel; Hölzel, Florian; Kühne, Stefan; Oberschmidt, Dirk; Arnold, ThomasThe production of mold inserts for the replication of micro-lens arrays through micro-embossing could be an alternative process route compared to diamond turning or milling in order to reduce time and costs. The rapidly solidified aluminum alloy RSA-501 is expected to form micro-structures with low surface roughness because of its ultra-fine grain structure. In micro-embossing challenges like elastic spring back effect, pile-ups, and forming accuracy depend on the material behavior. Therefore, RSA-501 was further characterized and the influence of polishing or flycutting on the material behavior was investigated. To further understand the grain and microstructure samples were sectioned along their cross and longitudinal directions. The grain structure of RSA-501 was oriented along the extrusion direction and the mean grain sizes were <1.00 μm. Furthermore, RSA-501 was micro-embossed to investigate the influence of the material behavior and surface preparation on the forming of micro-structures. The induced surface integrity through flycutting was not deep enough to influence the forming of micro-structures. Therefore, the workpiece surface can be prepared either by polishing or flycutting. When micro-embossing RSA-501, cross and longitudinal sections can be used. However, it is recommended to process the cross section because of its isotropic grain structure. It was shown that the curvature radius of micro-embossed concave structures differs from the tool radius. This is due to the elastic spring back effect. Since the embossed structure remains spherical, the spring back effect can be compensated by adjusting the tool radius.
- ItemReversibly compressible and freestanding monolithic carbon spherogels(Amsterdam : Elsevier, 2019) Salihovic, M.; Zickler, G.A.; Fritz-Popovski, G.; Ulbricht, M.; Paris, O.; Hüsing, N.; Presser, V.; Elsaesser, M.S.We present a versatile strategy to tailor the nanostructure of monolithic carbon aerogels. By use of an aqueous colloidal solution of polystyrene in the sol-gel processing of resorcinol-formaldehyde gels, we can prepare, after supercritical drying and successive carbonization, freestanding monolithic carbon aerogels, solely composed of interconnected and uniformly sized hollow spheres, which we name carbon spherogels. Each sphere is enclosed by a microporous carbon wall whose thickness can be adjusted by the polystyrene concentration, which affects the pore texture as well as the mechanical properties of the aerogel monolith. In this study, we used monodisperse polystyrene spheres of approximately 250 nm diameter, which result in an inner diameter of the final hollow carbon spheres of approximately 200 ± 5 nm due to shrinkage during the carbonization process. The excellent homogeneity of the samples, as well as uniform sphere geometries, are confirmed by small- and angle X-ray scattering. The presence of macropores between the hollow spheres creates a monolithic network with the benefit of being reversibly compressible up to 10% linear strain without destruction. Electrochemical tests demonstrate the applicability of ground and CO2 activated carbon spherogels as electrode materials. © 2019 The Authors
- ItemDetermination of fluoride component in the multifunctional refining flux used for recycling aluminum scrap(Amsterdam : Elsevier, 2020) Wan, Bingbing; Li, Wenfang; Liu, Fangfang; Lu, Tiwen; Jin, Shuoxun; Wang, Kang; Yi, Aihua; Tian, Jun; Chen, WeipingIn this paper, the optimum fluoride component in the multifunctional refining flux used for recycling aluminum scrap was determined. Theoretical analysis of solid fluxing shows that strong stripping ability of oxide layer on aluminum surface for the flux and appropriate interfacial tensions between Al melt / inclusion (σM-I), flux / inclusion (σF-I), and flux / Al melt (σF-M) are indispensable for making the flux achieve the properties of covering, drossing, and cleaning simultaneously. In term of four preliminarily selected fluoride salts, i.e., KF, AlF3, K3AlF6 and KAlF4, the results of interfacial tension measurements indicates that, combined addition of A-type fluoride (KF) and B-type fluoride (AlF3, K3AlF6 and KAlF4) to equimolar NaCl-KCl can just offset the shortage of single addition of KF which means worsening the separating effect of flux from melt surface and weakening the wettability of flux on the inclusions due to the lower σF-M and the higher σF-I respectively. Additionally, coalescence behaviors of aluminum droplets in molten fluxes reveals that, KF, K3AlF6 or KAlF4 possesses stronger stripping ability of oxide layer, while the stripping ability of oxide layer for AlF3 is weaker. Ultimately, the combination of KF with K3AlF6 or/and KAlF4 is ascertained to be an optimum selection for fluoride component in the multifunctional refining flux.
- ItemRedox-electrolytes for non-flow electrochemical energy storage: A critical review and best practice(Amsterdam : Elsevier, 2019) Lee, J.; Srimuk, P.; Fleischmann, S.; Su, X.; Hatton, T.A.; Presser, V.Over recent decades, a new type of electric energy storage system has emerged with the principle that the electric charge can be stored not only at the interface between the electrode and the electrolyte but also in the bulk electrolyte by redox activities of the electrolyte itself. Those redox electrolytes are promising for non-flow hybrid energy storage systems, or redox electrolyte-aided hybrid energy storage (REHES) systems; particularly, when they are combined with highly porous carbon electrodes. In this review paper, critical design considerations for the REHES systems are discussed as well as the effective electrochemical characterization techniques. Appropriate evaluation of the electrochemical performance is discussed thoroughly, including advanced analytical techniques for the determination of the electrochemical stability of the redox electrolytes and self-discharge rate. Additionally, critical summary tables for the recent progress on REHES systems are provided. Furthermore, the unique synergistic combination of porous carbon materials and redox electrolytes is introduced in terms of the diffusion, adsorption, and electrochemical kinetics modulating energy storage in REHES systems. © 2018 The Author(s)
- ItemGain and lasing from CdSe/CdS nanoplatelet stripe waveguides(Amsterdam : Elsevier, 2022) Belitsch, Martin; Dirin, Dmitry N.; Kovalenko, Maksym V.; Pichler, Kevin; Rotter, Stefan; Ghalgaoui, Ahmed; Ditlbacher, Harald; Hohenau, Andreas; Krenn, Joachim R.Colloidal semiconducting nanocrystals are efficient, stable and spectrally tunable emitters, but achievable optical gain is often limited by fast nonradiative processes. These processes are strongly suppressed in slab-shaped nanocrystals (nanoplatelets), due to relaxed exciton Coulomb interaction. Here, we show that CdSe/CdS nanoplatelets can be engineered into (sub)microscopic stripe waveguides that achieve lasing without further components for feedback, i.e., just relying on the stripe end reflection. We find a remarkably high gain factor for the CdSe/CdS nanoplatelets of 1630 cm−1. In addition, by comparison with numerical simulations we assign a distinct emission peak broadening above laser threshold to emission pulse shortening. Our results illustrate the feasibility of geometrically simple monolithic microscale nanoplatelet lasers as an attractive option for a variety of photonic applications.
- ItemIntrinsic modulus and strain coefficients in dilute composites with a Neo-Hookean elastic matrix(Amsterdam : Elsevier, 2022) Ivaneyko, Dmytro; Domurath, Jan; Heinrich, Gert; Saphiannikova, MarinaA finite element modelling of dilute elastomer composites based on a Neo-Hookean elastic matrix and rigid spherical particles embedded within the matrix was performed. In particular, the deformation field in vicinity of a sphere was simulated and numerical homogenization has been used to obtain the effective modulus of the composite μeff for different applied extension and compression ratios. At small deformations the well-known Smallwood result for the composite is reproduced: μeff=(1+[μ]φ)μ0 with the intrinsic modulus [μ]=2.500. Here φ is the volume fraction of particles and μ0 is the modulus of the matrix solid. However at larger deformations higher values of the intrinsic modulus [μ] are obtained, which increase quadratically with the applied true strain. The homogenization procedure allowed to extract the intrinsic strain coefficients which are mirrored around the undeformed state for principle extension and compression axes. Utilizing the simulation results, stress and strain modifications of the Neo-Hookean strain energy function for dilute composites are proposed.
- ItemPre and post-treatments to improve weldability and mechanical properties of aluminum-polyamide laser welded specimens(Amsterdam : Elsevier, 2020) Elahi, Mahdi Amne; Koch, Marcus; Heck, Mike; Plapper, PeterThe laser polishing surface treatment is a prerequisite for enhanced weldability that is enabled by superior adhesion between the weldments. The paper describes the laser polishing process of the aluminum surface to develop a relatively thick and porous artificial aluminum oxide layer. Microscopic observation shows the laser polishing process significantly improves the adhesion of molten polyamide to the aluminum surface. Besides, the shear load of the pretreated joints is much higher than that of as-received ones. However, for the majority of the welded samples, the failure happens at the polyamide near the interface of aluminum/polyamide due to the thermal effect and structural changes of polyamide during the welding process. By applying the post-treatment of the welded specimens with different cycles, the mentioned failure mechanism is not observed anymore. Therefore, the mechanical properties of the joint will be improved and reach to the limits of the base materials.