71 results
Search Results
Now showing 1 - 10 of 71
- ItemStrain induced power enhancement of far-UVC LEDs on high temperature annealed AlN templates(Melville, NY : American Inst. of Physics, 2023) Knauer, A.; Kolbe, T.; Hagedorn, S.; Hoepfner, J.; Guttmann, M.; Cho, H.K.; Rass, J.; Ruschel, J.; Einfeldt, S.; Kneissl, M.; Weyers, M.High temperature annealed AlN/sapphire templates exhibit a reduced in-plane lattice constant compared to conventional non-annealed AlN/sapphire grown by metalorganic vapor phase epitaxy (MOVPE). This leads to additional lattice mismatch between the template and the AlGaN-based ultraviolet-C light emitting diode (UVC LED) heterostructure grown on these templates. This mismatch introduces additional compressive strain in AlGaN quantum wells resulting in enhanced transverse electric polarization of the quantum well emission at wavelengths below 235 nm compared to layer structures deposited on conventional MOVPE-grown AlN templates, which exhibit mainly transverse magnetic polarized emission. In addition, high temperature annealed AlN/sapphire templates also feature reduced defect densities leading to reduced non-radiative recombination. Based on these two factors, i.e., better outcoupling efficiency of the transverse electric polarized light and an enhanced internal quantum efficiency, the performance characteristic of far-UVC LEDs emitting at 231 nm was further improved with a cw optical output power of 3.5 mW at 150 mA.
- ItemA 310 nm Optically Pumped AlGaN Vertical-Cavity Surface-Emitting Laser(Washington, DC : ACS Publications, 2021) Hjort, Filip; Enslin, Johannes; Cobet, Munise; Bergmann, Michael A.; Gustavsson, Johan; Kolbe, Tim; Knauer, Arne; Nippert, Felix; Häusler, Ines; Wagner, Markus R.; Wernicke, Tim; Kneissl, Michael; Haglund, ÅsaUltraviolet light is essential for disinfection, fluorescence excitation, curing, and medical treatment. An ultraviolet light source with the small footprint and excellent optical characteristics of vertical-cavity surface-emitting lasers (VCSELs) may enable new applications in all these areas. Until now, there have only been a few demonstrations of ultraviolet-emitting VCSELs, mainly optically pumped, and all with low Al-content AlGaN cavities and emission near the bandgap of GaN (360 nm). Here, we demonstrate an optically pumped VCSEL emitting in the UVB spectrum (280-320 nm) at room temperature, having an Al0.60Ga0.40N cavity between two dielectric distributed Bragg reflectors. The double dielectric distributed Bragg reflector design was realized by substrate removal using electrochemical etching. Our method is further extendable to even shorter wavelengths, which would establish a technology that enables VCSEL emission from UVA (320-400 nm) to UVC (<280 nm). © 2020 American Chemical Society. All rights reserved.
- ItemSkin tolerant inactivation of multiresistant pathogens using far-UVC LEDs([London] : Macmillan Publishers Limited, part of Springer Nature, 2021) Glaab, Johannes; Lobo-Ploch, Neysha; Cho, Hyun Kyong; Filler, Thomas; Gundlach, Heiko; Guttmann, Martin; Hagedorn, Sylvia; Lohan, Silke B.; Mehnke, Frank; Schleusener, Johannes; Sicher, Claudia; Sulmoni, Luca; Wernicke, Tim; Wittenbecher, Lucas; Woggon, Ulrike; Zwicker, Paula; Kramer, Axel; Meinke, Martina C.; Kneissl, Michael; Weyers, Markus; Winterwerber, Ulrike; Einfeldt, SvenMultiresistant pathogens such as methicillin-resistant Staphylococcus aureus (MRSA) cause serious postoperative infections. A skin tolerant far-UVC (< 240 nm) irradiation system for their inactivation is presented here. It uses UVC LEDs in combination with a spectral filter and provides a peak wavelength of 233 nm, with a full width at half maximum of 12 nm, and an irradiance of 44 µW/cm2. MRSA bacteria in different concentrations on blood agar plates were inactivated with irradiation doses in the range of 15–40 mJ/cm2. Porcine skin irradiated with a dose of 40 mJ/cm2 at 233 nm showed only 3.7% CPD and 2.3% 6-4PP DNA damage. Corresponding irradiation at 254 nm caused 11–14 times higher damage. Thus, the skin damage caused by the disinfectant doses is so small that it can be expected to be compensated by the skin's natural repair mechanisms. LED-based far-UVC lamps could therefore soon be used in everyday clinical practice to eradicate multiresistant pathogens directly on humans.
- ItemIn vivo detection of changes in cutaneous carotenoids after chemotherapy using shifted excitation resonance Raman difference and fluorescence spectroscopy(Oxford [u.a.] : Wiley-Blackwell, 2020) Jung, Sora; Darvin, Maxim E.; Schleusener, Johannes; Thiede, Gisela; Lademann, Juergen; Braune, Marcel; Elban, Felia; Fuss, HaraldBackground: Various cutaneous toxicities under chemotherapy indicate a local effect of chemotherapy by secretion after systemic application. Here, changes in the fluorescence and Raman spectral properties of the stratum corneum subsequent to intravenous chemotherapy were assessed. Methods: Twenty healthy subjects and 20 cancer patients undergoing chemotherapy were included. Measurement time points in cancer patients were before the first cycle of chemotherapy (Tbase) and immediately after intravenous application of the chemotherapy (T1). Healthy subjects were measured once without any further intervention. Measurements were conducted using an individually manufactured system consisting of a handheld probe and a wavelength-tunable diode laser-based 488 nm SHG light source. Hereby, changes in both skin fluorescence and shifted excitation resonance Raman difference spectroscopy (SERRDS) carotenoid signals were assessed. Results: Healthy subjects showed significantly (P <.001) higher mean concentrations of carotenoids compared to cancer subjects at Tbase. An increase in fluorescence intensity was detected in almost all patients after chemotherapy, especially after doxorubicin infusion. Furthermore, a decrease in the carotenoid concentration in the skin after chemotherapy was found. Conclusion: The SERRDS based noninvasive detection can be used as an indirect quantitative assessment of fluorescent chemotherapeutics. The lower carotenoid SERRDS intensities at Tbase might be due to cancerous diseases and co-medication. © 2020 The Authors. Skin Research and Technology Published by John Wiley & Sons Ltd.
- ItemLow resistance n-contact for UVC LEDs by a two-step plasma etching process(Bristol : IOP Publ., 2020) Cho, H.K.; Kang, J.H.; Sulmoni, L.; Kunkel, K.; Rass, J.; Susilo, N.; Wernicke, T.; Einfeldt, S.; Kneissl, M.The impact of plasma etching on the formation of low-resistance n-contacts on the AlGaN:Si current spreading layer during the chip fabrication of ultraviolet light-emitting diodes (UV LEDs) emitting at 265 nm is investigated. A two-step plasma etching process with a first rapid etching using BCl3/Cl2 gas mixture and a second slow etching step using pure Cl2 gas has been developed. The etching sequence provides smooth mesa side-walls and an n-AlGaN surface with reduced surface damage. Ohmic n-contacts with a contact resistivity of 3.5 10-4 Ωcm2 are obtained on Si-doped Al0.65Ga0.35N layers and the operating voltages of the UVC LEDs were reduced by 2 V for a current of 20 mA. © 2020 The Author(s). Published by IOP Publishing Ltd.
- ItemHigh-brightness broad-area diode lasers with enhanced self-aligned lateral structure(Bristol : IOP Publ., 2020) Elatta, M.; Brox, O.; Della Casa, P.; Maaßdorf, A.; Martin, D.; Wenzel, H.; Knigge, A.; Crump, P.Broad-area diode lasers with increased brightness and efficiency are presented, which are fabricated using an enhanced self-aligned lateral structure by means of a two-step epitaxial growth process with an intermediate etching step. In this structure, current-blocking layers in the device edges ensure current confinement under the central stripe, which can limit the detrimental effects of current spreading and lateral carrier accumulation on beam quality. It also minimizes losses at stripe edges, thus lowering the lasing threshold and increasing conversion efficiency, while maintaining high polarization purity. In the first realization of this structure, the current block is integrated within an extreme-triple-asymmetric epitaxial design with a thin p-doped side, meaning that the distance between the current block and the active zone can be minimized without added process complexity. Using this configuration, enhanced self-aligned structure devices with 90 µm stripe width and 4 mm resonator length show up to 20% lower threshold current, 21% narrower beam waist, and slightly higher (1.03 ) peak efficiency in comparison to reference devices with the same dimensions, while slope, divergence angle and polarization purity remain almost unchanged. These results correspond to an increase in brightness by up to 25%, and measurement results of devices with varying stripe widths follow the same trend. © 2020 The Author(s). Published by IOP Publishing Ltd.
- ItemImpact of the capture time on the series resistance of quantum-well diode lasers(Bristol : IOP Publ., 2020) Boni, A.; Wünsche, H.J.; Wenzel, H.; Crump, P.Electrons and holes injected into a semiconductor heterostructure containing quantum wells are captured with a finite time. We show theoretically that this very fact can cause a considerable excess contribution to the series resistivity and this is one of the main limiting factors to higher efficiency for GaAs based high-power lasers. The theory combines a standard microscopic-based model for the capture-escape processes in the quantum well with a drift-diffusion description of current flow outside the quantum well. Simulations of five GaAs-based devices differing in their Al-content reveal the root-cause of the unexpected and until now unexplained increase of the series resistance with decreasing heat sink temperature measured recently. The finite capture time results in resistances in excess of the bulk layer resistances (decreasing with increasing temperature) from 1 mΩ up to 30 mΩ in good agreement with the experiment. © 2020 The Author(s). Published by IOP Publishing Ltd.
- ItemLow-index quantum-barrier single-pass tapered semiconductor optical amplifiers for efficient coherent beam combining(Bristol : IOP Publ., 2020) Albrodt, P.; Niemeyer, M.; Elattar, M.; Hamperl, J.; Blume, G.; Ginolas, A.; Fricke, J.; Maaßdorf, A.; Georges, P.; Lucas-Leclin, G.; Paschke, K.; Crump, P.The requirements for coherent combination of high power GaAs-based single-pass tapered amplifiers are studied. Changes to the epitaxial layer structure are shown to bring higher beam quality and hence improved combining efficiency for one fixed device geometry. Specifically, structures with large vertical near field and low wave-guiding from the active region show 10% higher beam quality and coherent combining efficiency than reference devices. As a result, coherent combining efficiency is shown to be limited by beam quality, being directly proportional to the power content in the central lobe across a wide range of devices with different construction. In contrast, changes to the in-plane structure did not improve beam quality or combining efficiency. Although poor beam quality does correlate with increased optical intensities near the input aperture, locating monolithically-integrated absorption regions in these areas did not lead to any performance improvement. However, large area devices with subsequently improved cooling do achieve higher output powers. Phase noise can limit coherent combining, but this is shown to be small and independent of device design. Overall, tapered amplifiers are well suited for high power coherent combining applications. © 2020 The Author(s). Published by IOP Publishing Ltd.
- ItemOptimized diamond inverted nanocones for enhanced color center to fiber coupling(Melville, NY : American Inst. of Physics, 2021) Torun, Cem Güney; Schneider, Philipp-Immanuel; Hammerschmidt, Martin; Burger, Sven; Munns, Joseph H. D.; Schröder, TimNanostructures can be used for boosting the light outcoupling of color centers in diamond; however, the fiber coupling performance of these nanostructures is rarely investigated. Here, we use a finite element method for computing the emission from color centers in inverted nanocones and the overlap of this emission with the propagation mode in a single-mode fiber. Using different figures of merit, the inverted nanocone parameters are optimized to obtain maximal fiber coupling efficiency, free-space collection efficiency, or rate enhancement. The optimized inverted nanocone designs show promising results with 66% fiber coupling or 83% free-space coupling efficiency at the tin-vacancy center zero-phonon line wavelength of 619 nm. Moreover, when evaluated for broadband performance, the optimized designs show 55% and 76% for fiber coupling and free-space efficiencies, respectively, for collecting the full tin-vacancy emission spectrum at room temperature. An analysis of fabrication insensitivity indicates that these nanostructures are robust against imperfections. For maximum emission rate into a fiber mode, a design with a Purcell factor of 2.34 is identified. Finally, possible improvements offered by a hybrid inverted nanocone, formed by patterning into two different materials, are investigated and increase the achievable fiber coupling efficiency to 71%. © 2021 Author(s).
- ItemThe patterning toolbox FIB-o-mat: Exploiting the full potential of focused helium ions for nanofabrication(Frankfurt, M. : Beilstein-Institut zur Förderung der Chemischen Wissenschaften, 2021) Deinhart, Victor; Kern, Lisa-Marie; Kirchhof, Jan N.; Juergensen, Sabrina; Sturm, Joris; Krauss, Enno; Feichtner, Thorsten; Kovalchuk, Sviatoslav; Schneider, Michael; Engel, Dieter; Pfau, Bastian; Hecht, Bert; Bolotin, Kirill I.; Reich, Stephanie; Höflich, KatjaFocused beams of helium ions are a powerful tool for high-fidelity machining with spatial precision below 5 nm. Achieving such a high patterning precision over large areas and for different materials in a reproducible manner, however, is not trivial. Here, we introduce the Python toolbox FIB-o-mat for automated pattern creation and optimization, providing full flexibility to accomplish demanding patterning tasks. FIB-o-mat offers high-level pattern creation, enabling high-fidelity large-area patterning and systematic variations in geometry and raster settings. It also offers low-level beam path creation, providing full control over the beam movement and including sophisticated optimization tools. Three applications showcasing the potential of He ion beam nanofabrication for two-dimensional material systems and devices using FIB-o-mat are presented.