11 results
Search Results
Now showing 1 - 10 of 11
- ItemThermal annealing to influence the vapor sensing behavior of co-continuous poly(lactic acid)/polystyrene/multiwalled carbon nanotube composites(Amsterdam [u.a.] : Elsevier Science, 2020) Li, Yilong; Pionteck, Jürgen; Pötschke, Petra; Voit, BrigitteWith the main purpose of being used as vapor leakage detector, the volatile organic compound (VOC) vapor sensing properties of conductive polymer blend composites were studied. Poly(lactic acid)/polystyrene/multi-walled carbon nanotube (PLA/PS/MWCNT) based conductive polymer composites (CPCs) in which the polymer components exhibit different interactions with the vapors, were prepared by melt mixing. CPCs with a blend composition of 50/50 wt% resulted in the finest co-continuous structure and selective MWCNT localization in PLA. Therefore, these composites were selected for sensor tests. Thermal annealing was applied aiming to maintain the blend structure but improving the sensing reversibility of CPC sensors towards high vapor concentrations. Different sensing protocols were applied using acetone (good solvent for PS and PLA) and cyclohexane (good solvent for PS but poor solvent for PLA) vapors. Increasing acetone vapor concentration resulted in increased relative resistance change (Rrel) of CPCs. Saturated cyclohexane vapor resulted in lower response than nearly saturated acetone vapor. The thermal annealing at 150 °C did not change the blend morphology but increased the PLA crystallinity, making the CPC sensors more resistant to vapor stimulation, resulting in lower Rrel but better reversibility after vapor exposure.
- ItemA new strategy to improve viscoelasticity, crystallization and mechanical properties of polylactide(Amsterdam [u.a.] : Elsevier Science, 2021) Huang, Ying; Müller, Michael Thomas; Boldt, Regine; Zschech, Carsten; Gohs, Uwe; Wießner, SvenBiodegradable polylactide/masticated natural rubber (PLA/mNR) blends were prepared by electron induced reactive processing (EIReP) without using any chemical additives. The PLA/mNR blends showed droplet-matrix morphology with decreased mNR particle size after EIReP treatment. The absolute value of complex viscosity and storage modulus increased significantly for the EIReP modified blends, suggesting the improved melt strength and elasticity. The crystallization investigation showed that the cold crystallization peak of PLA phase gradually disappeared after EIReP modification. Instead, the crystallization peak arose during melt cooling process. Consequently, the crystallinity of PLA phase increased from 6.2% to 39.0% as the mNR content increased from 0 to 20 wt%. It was found that the softening temperature of PLA examined by dynamic mechanical analysis increased effectively with the characters of higher modulus compared to the non-modified blends. The EIReP modified blends exhibited excellent mechanical properties with 7-fold increase of impact toughness compared with neat PLA, implying a superior interfacial adhesion and chain interactions between the two polymer phases. Furthermore, the thermogravimetric analysis demonstrated that the thermal stability was slightly enhanced for the EIReP modified blends.
- ItemSpecial issue on “Ultrasound-assisted engineering of materials for biomedical uses”(Amsterdam [u.a.] : Elsevier Science, 2022) Besford, Quinn A.; Cavalieri, Francesca[no abstract available]
- ItemTransparent model concrete with tunable rheology for investigating flow and particle-migration during transport in pipes(Amsterdam [u.a.] : Elsevier Science, 2020) Auernhammer, Günter K.; Fataei, Shirin; Haustein, Martin A.; Patel, Himanshu P.; Schwarze, Rüdiger; Secrieru, Egor; Mechtcherine, ViktorThe article describes the adaption and properties of a model concrete for detailed flow studies. To adapt the yield stress and plastic viscosity of the model concrete to the corresponding rheological properties of real concrete, the model concrete is made of a mixture of glass beads and a non-Newtonian fluid. The refractive index of the non-Newtonian fluid is adjusted to the refractive index of the glass beads by the addition of a further constituent. The rheological properties of the model concrete are characterised by measurements in concrete rheometers. Finally, the first exemplary results from experiments with the model concrete are presented, which give incipient impressions of the complex internal dynamics in flowing concrete.
- ItemControlled synthesis of mussel-inspired Ag nanoparticle coatings with demonstrated in vitro and in vivo antibacterial properties(Amsterdam [u.a.] : Elsevier Science, 2021) Wang, Xiaowei; Xu, Kehui; Cui, Wendi; Yang, Xi; Maitz, Manfred F.; Li, Wei; Li, Xiangyang; Chen, JialongThe in-situ formation of silver nanoparticles (AgNPs) via dopamine-reduction of Ag+ has been widely utilized for titanium implants to introduce antibacterial properties. In previous studies, the preparation of AgNPs has focused on controlling the feeding concentrations, while the pH of the reaction solution was ignored. Herein, we systematically determined the influence of various pH (4, 7, 10) and Ag+ concentrations (0.01, 0.1 mg/mL) on the AgNPs formation, followed by the evaluation of the antibacterial properties in vitro and in vivo. The results revealed that an alkaline environment was favourable for AgNP formation and resulted in more particles. Although the AgNPs bearing Ti had lower biocompatibilities, it was significantly improved after 7 days of mineralization in simulated body fluid. The outstanding antibacterial property of the AgNPs was well maintained after one day and seven days of implantation. Moreover, 3D micro-CT modelling showed that the pH 10/0.1 group exhibited remarkable osteogenesis, which may be due to their strong antibacterial properties and ability to promote mineralization. Therefore, we have demonstrated that the solution pH was as important as the feeding Ag+ concentration in determining AgNP formation, and it has paved the way for developing various AgNP-loaded surfaces that could meet different antibacterial needs.
- ItemExamining the early stages of thermal oxidative degradation in epoxy-amine resins(Amsterdam [u.a.] : Elsevier Science, 2020) Morsch, Suzanne; Liu, Yanwen; Lyon, S.B.; Gibbon, S.R.; Gabriele, Benjamin; Malanin, Mikhail; Eichhorn, Klaus-JochenEpoxy-amine resins continue to find widespread use as the binders in protective and decorative organic coatings, as the matrix in composite materials, and as adhesives. In service, exposure to the environment ultimately results in oxidative deterioration of these materials, limiting the performance lifetime. Defining this auto-oxidation process is therefore a key challenge in developing more durable high-performance materials. In this study, we investigate oxidative degradation of a model resin based on diglycidyl ether of bisphenol-A (DGEBA) and an aliphatic amine hardener, triethylenetetraamine (TETA). Using infrared spectroscopy, we find that prior to the expected detection of formate groups (corresponding to the well-known radical oxidation mechanism of DGEBA), a band at 1658 cm−1 forms, associated with amine cross-linker oxidation. Infrared microspectroscopy, in-situ heated ATR-infrared, Raman spectroscopy and AFM-IR techniques are thus employed to investigate the early stages of resin oxidation and demonstrate strong parallels between the initial stages of cured resin degradation and the auto-oxidation of TETA cross-linker molecules.
- ItemA review of electrical and thermal conductivities of epoxy resin systems reinforced with carbon nanotubes and graphene-based nanoparticles(Amsterdam [u.a.] : Elsevier Science, 2022) Mousavi, Seyed Rasoul; Estaji, Sara; Kiaei, Hediyeh; Mansourian-Tabaei, Mohammad; Nouranian, Sasan; Jafari, Seyed Hassan; Ruckdäschel, Holger; Arjmand, Mohammad; Khonakdar, Hossein AliEpoxy (EP) resins exhibit desirable mechanical and thermal properties, low shrinkage during cuing, and high chemical resistance. Therefore, they are useful for various applications, such as coatings, adhesives, paints, etc. On the other hand, carbon nanotubes (CNT), graphene (Gr), and their derivatives have become reinforcements of choice for EP-based nanocomposites because of their extraordinary mechanical, thermal, and electrical properties. Herein, we provide an overview of the last decade's advances in research on improving the thermal and electrical conductivities of EP resin systems modified with CNT, Gr, their derivatives, and hybrids. We further report on the surface modification of these reinforcements as a means to improve the nanofiller dispersion in the EP resins, thereby enhancing the thermal and electrical conductivities of the resulting nanocomposites.
- ItemExperimental multi-scale approach to determine the local mechanical properties of foam base material in polyisocyanurate metal panels(Amsterdam [u.a.] : Elsevier Science, 2021) Gahlen, P.; Fröbel, S.; Karbach, A.; Gabriel, D.; Stommel, M.Polyisocyanurate (PIR) foams were examined regarding their local chemical composition using ATR-IR spectroscopy. As a special parameter the PIR: Amide III intensity ratio is to be mentioned, which represents the quantity of the formed PIR groups. Based on the local PIR: Amide III intensity ratio, the mechanical properties (Young's modulus) of the foam base material were analyzed at defined positions by AFM and Nanoindentation. It turned out that the AFM method is only suitable for qualitative analysis, because the values differ strongly from macroscopic measurements. For the measurements using nanoindentation, a new embedding method was developed, which achieves significantly more realistic and reproducible results compared to the embedding method used in the literature and shows a very good agreement with the macroscopic values. In general, it has been shown that a higher PIR: Amide III intensity ratio tends to lead to a higher Young's modulus. Nevertheless, there are other, currently unknown characteristic values which also influence the Young's modulus.
- ItemResolving mobility anisotropy in quasi-free-standing epitaxial graphene by terahertz optical Hall effect(Amsterdam [u.a.] : Elsevier Science, 2021) Armakavicius, Nerijus; Kühne, Philipp; Eriksson, Jens; Bouhafs, Chamseddine; Stanishev, Vallery; Ivanov, Ivan G.; Yakimova, Rositsa; Zakharov, Alexei A.; Al-Temimy, Ameer; Coletti, Camilla; Schubert, Mathias; Darakchieva, VanyaIn this work, we demonstrate the application of terahertz-optical Hall effect (THz-OHE) to determine directionally dependent free charge carrier properties of ambient-doped monolayer and quasi-free-standing-bilayer epitaxial graphene on 4H–SiC(0001). Directionally independent free hole mobility parameters are found for the monolayer graphene. In contrast, anisotropic hole mobility parameters with a lower mobility in direction perpendicular to the SiC surface steps and higher along the steps in quasi-free-standing-bilayer graphene are determined for the first time. A combination of THz-OHE, nanoscale microscopy and optical spectroscopy techniques are used to investigate the origin of the anisotropy. Different defect densities and different number of graphene layers on the step edges and terraces are ruled out as possible causes. Scattering mechanisms related to doping variations at the step edges and terraces as a result of different interaction with the substrate and environment are discussed and also excluded. It is suggested that the step edges introduce intrinsic scattering in quasi-free-standing-bilayer graphene, that is manifested as a result of the higher ratio between mean free path and average terrace width parameters. The suggested scenario allows to reconcile existing differences in the literature regarding the anisotropic electrical transport in epitaxial graphene. © 2020 Elsevier Ltd
- ItemFrom microfluidics to hierarchical hydrogel materials(Amsterdam [u.a.] : Elsevier Science, 2023) Weigel, Niclas; Li, Yue; Fery, Andreas; Thiele, JulianOver the past two decades, microfluidics has made significant contributions to material and life sciences, particularly via the design of nano-, micro- and mesoscale materials such as nanoparticles, micelles, vesicles, emulsion droplets, and microgels. Unmatched in control over a multitude of material parameters, microfluidics has also shed light on fundamental aspects of material design such as the early stages of nucleation and growth processes as well as structure evolution. Exemplarily, polymer hydrogel particles can be formed via microfluidics with exact control over size, shape, functionalization, compartmentalization, and mechanics that is hardly found in any other processing method. Interestingly, the utilization of microfluidics for material design largely focuses on the fabrication of single entities that act as reaction volume for organic and cell-free biosynthesis, cell mimics, or local environment for cell culturing. In recent years, however, hydrogel design has shifted towards structures that integrate a large variety of functions, e.g., to address the demands for sensing tasks in a complex environment or more closely mimicking architecture and organization of tissue by multiparametric cultures. Hence, this review provides an overview of recent literature that explores microfluidics for fabricating hydrogel materials that go well beyond common length scales as well as the structural and functional complexity of microgels necessary to produce hierarchical hydrogel structures. We focus on examples that utilize microfluidics to design microgel-based assemblies, on microfluidically made polymer microgels for 3D bioprinting, on hydrogels fabricated by microfluidics in a continuous fashion, like fibers, and on hydrogel structures that are shaped by microchannels.