4 results
Search Results
Now showing 1 - 4 of 4
- ItemTowards hybrid one-pot/one-electrode Pd-NPs-based nanoreactors for modular biocatalysis(Amsterdam [u.a.] : Elsevier, 2021) Koch, M.; Apushkinskaya, N.; Zolotukhina, E.V.; Silina, Y.E.Here, fundamental aspects affecting template-assisted engineering of oxidase-associated peroxide oxidation co-catalysis of the modeled microanalytical system based on the hybrid palladium nanoparticles (Pd-NPs) with tailored functional properties were studied. By an accurate tuning and validation of the experimental setup, a modular Pd-NPs-doped one-pot/one-electrode amperometric nanobiosensor for advanced multiplex analyte detection was constructed. The specific operational conditions (electrochemical read-out mode, pH, regeneration procedure) of the modular one-pot/one-electrode nanobiosensor allowed a reliable sensing of L-lactate (with linear dynamic range, LDR = 500 µM – 2 mM, R2 = 0.977), D-glucose (with LDR = 200 µM – 50 mM, R2 = 0.987), hydrogen peroxide (with LDR = 20 µM – 100 mM, R2 = 0.998) and glutaraldehyde (with LDR = 1 – 100 mM, R2 = 0.971). In addition, mechanistic aspects influencing the performance of Pd-NPs-doped one-pot/one-electrode for multiplex analyte sensing were studied in detail. The designed one-pot/one-electrode amperometric nanobiosensor showed a thin layer electrochemical behavior that greatly enhanced electron transfer between the functional hybrid layer and the electrode. Finally, a specific regeneration procedure of the hybrid one-pot/one-electrode and algorithm towards its usage for modular biocatalysis were developed. The reported strategy can readily be considered as a guideline towards the fabrication of commercialized nanobiosensors with tailored properties for advanced modular biocatalysis.
- ItemFailure mechanism analysis based on laser-based surface treatments for aluminum-polyamide laser joining(Amsterdam [u.a.] : Elsevier, 2021) Elahi, Amne; Koch, Marcus; Bardon, Julien; Addiego, Frédéric; Plapper, PeterThe development of strong metal to polymer assemblies is currently an important research subject thanks to its prominence to develop lightweight structures. Furthermore, laser welding is known to be a fast, reliable, and versatile joining process, and it was demonstrated recently that it can be applied to such metal to polymer systems. To enhance the mechanical properties of the laser-joined aluminum-polyamide (Al-PA) specimens, laser polishing and laser ablation processes have been implemented on the aluminum surface before joining. The polyamide surface was also treated with the laser beam, separately. The surfaces were tested by several characterization techniques before and after each surface treatment. Then aluminum and polyamide samples with different surface treatments have been joined with an identical laser joining process. The mechanical properties of the joints in single lap shear configuration are reported and the failure mechanisms are discussed based on micro-computed x-ray tomography imaging of joined specimens and microscopic analysis before failure. Results show that both surface treatments of aluminum significantly improve the shear load of the joint; however, with different failure mechanisms. Polyamide surface treatment and increasing degree of crystallinity are effective when combined with the laser polishing of the Al surface. This combination is responsible for further enhancement of the shear load of the joint to the limit of base metal strength which is approximately 60 % improvement compared to the untreated samples. Finally, energy dispersive X-ray mapping shows the physicochemical bonding between aluminum oxide and polyamide at the interface.
- ItemAdhesion of a cylindrical punch with elastic properties that vary radially(Amsterdam [u.a.] : Elsevier, 2023) Kossa, Attila; Hensel, René; McMeeking, Robert M.The adhesion of a rigid substrate and an adhered straight cylindrical punch with a non-homogeneous elastic modulus is analyzed. The stress distributions are obtained along the interface for various elastic modulus gradients. The calculations are performed in the commercial finite element software Abaqus using a user material (UMAT) subroutine to control the dependence of Young's modulus on the radial position. The UMAT code is shared in the paper. The results reveal that the decreasing elastic modulus toward the perimeter of the punch can be used to significantly reduce the normal stress magnitudes in the singularity domain, which leads to stronger adhesion. The increase in the adhesion strength is characterized numerically. The effect of Poisson's ratio is also analyzed.
- ItemEndothelial cell spreading on lipid bilayers with combined integrin and cadherin binding ligands(Amsterdam [u.a.] : Elsevier, 2022) Koçer, Gülistan; Albino, Inês M.C.; Verheijden, Mark L.; Jonkheijm, PascalEndothelial cells play a central role in the vascular system, where their function is tightly regulated by both cell-extracellular matrix (e.g., via integrins) and cell–cell interactions (e.g., via cadherins). In this study, we incorporated cholesterol-modified integrin and N-cadherin peptide binding ligands in fluid supported lipid bilayers. Human umbilical vein endothelial cell adhesion, spreading and vinculin localization in these cells were dependent on ligand density. One composition led to observe a higher extent of cell spreading, where cells exhibited extensive lamellipodia formation and a qualitatively more distinct N-cadherin localization at the cell periphery, which is indicative of N-cadherin clustering and a mimic of cell–cell contact formation. The results can be used to reconstitute the endothelial-pericyte interface on biomedical devices and materials.