Search Results
Predicting the dominating factors during heat transfer in magnetocaloric composite wires
Magnetocaloric composite wires have been studied by pulsed-field measurements up to μ0ΔH = 10 T with a typical rise time of 13 ms in order to evaluate the evolution of the adiabatic temperature change of the core, ΔTad, and to determine the effective temperature change at the surrounding steel jacket, ΔTeff, during the field pulse. An inverse thermal hysteresis is observed for ΔTad due to the delayed thermal transfer. By numerical simulations of application-relevant sinusoidal magnetic field profiles, it can be stated that for field-frequencies of up to two field cycles per second heat can be efficiently transferred from the core to the outside of the jacket. In addition, intense numerical simulations of the temperature change of the core and jacket were performed by varying different parameters, such as frequency, heat capacity, thermal conductivity and interface resistance in order to shed light on their impact on ΔTeff at the outside of the jacket in comparison to ΔTad provided by the core.
Microstructure and elastic deformation behavior of β-type Ti-29Nb-13Ta-4.6Zr with promising mechanical properties for stent applications
In this paper, an attempt was made to combine theoretical composition design and thermo-mechanical treatments to produce a metastable β-type titanium alloy with mechanical compatibility for self-expandable stent applications. Metastable β-type Ti-29Nb-13Ta-4.6â»Zr (wt.%) thin-wires with an elastic modulus of 46â»GPa and a yield strength of 920â»MPa were successfully fabricated by cold rolling and low temperature aging. This combination of high yield strength and comparatively low elastic modulus resulted in enhanced elastic recoverable strain of 1.9%, which is much higher than that of the conventional metallic stent materials. The microstructure responsible for the much sought-after mechanical properties was observed to be mainly consisted of a homogeneous distribution of nanometer-sized α-precipitates in a β-phase matrix obtained via a spinodal decomposition of the pre-existed α″-martensite phase through α″â»→â»α″ leanâ»+â»α″ richâ»→â»αâ»+â»β. The α-precipitates increase the strength of the material by hindering the motion of dislocations (spinodal hardening) while the β-matrix with relatively low content of β-stabilizers gives rise to the observed low elastic modulus. More broadly, these findings could be extended to developing advanced metastable β-type titanium alloys for implant and other engineering applications.
Mechanical performance and corrosion behaviour of Zr-based bulk metallic glass produced by selective laser melting
Nearly fully dense, glassy Zr52.5Cu17.9Ni14.6Al10Ti5 bulk specimens were fabricated by selective laser melting (SLM) and their behaviour during compressive loading, during wear testing and in a corrosive medium was investigated. Their performance was compared with as-cast material of the same composition. The additively manufactured samples exhibit a yield strength around 1700 MPa combined with a plastic strain of about 0.5% after yielding despite the residual porosity of 1.3%, which is distributed uniformly in the samples. The propagation of shear bands in the bulk metallic glass prepared by SLM was studied. The specific wear rate and the worn surfaces demonstrated that similar wear mechanisms are active in the SLM and the as-cast samples. Hence, manufacturing the glass in layers does not adversely affect the wear properties. The same holds for the corrosion tests, which were carried out in 0.01 M Na2SO4 and 0.1 M NaCl electrolyte. The anodic polarization curves of SLM samples and as-cast samples revealed a similar corrosion behaviour. However, the SLM samples have a slightly reduced susceptibility to pitting corrosion and exhibit an improved surface healing ability, which might be attributed to an improved homogeneity of the additively manufactured glass.
Rejuvenation through plastic deformation of a La-based metallic glass measured by fast-scanning calorimetry
We explore the glassy states achievable after a metallic glass is formed on liquid quenching. Samples of La55Al25Ni20 (at.%) metallic glass (rod and ribbon) are studied. The extent of structural relaxation at room temperature is characterized for this low-glass-transition temperature glass. Plastic deformation (uniaxial compression) rejuvenates the glass to states of higher enthalpy characteristic of glass formation at high cooling rate. Deformation increases the heterogeneity of the glass, widening the spectrum of relaxation times. The extent of rejuvenation in samples of low aspect ratio is compared with that under conditions of high constraint in notched samples. The deformation-induced rejuvenation is particularly susceptible to reduction on subsequent ageing. Fast-scanning calorimetry is useful in characterizing the dynamics of structural relaxation. The shadow glass transition is more evident on fast heating, and is observed in this glass for the first time. A new excess exothermic effect is observed before the glass transition.
Electrical and magnetic properties of NiTiO3 nanoparticles synthesized by the sol-gel synthesis method and microwave sintering
In this paper, we focused on microwave sintered NiTiO3 nanoparticles synthesized via sol-gel method. The crystal structure was determined by the X-ray diffraction. Vibrational bands related to Ni-O and Ti-O bands were confirmed using the Fourier transform infrared spectrum. These NiTiO3 ceramics obeyed semiconductor behavior of Arrhenius type. The activation energy was found to be 0.04 μeV. The M-H curve exhibited superparamagnetic behavior at room temperature.
Glass-forming ability, phase formation and mechanical properties of glass-forming Cu-Hf-Zr alloys
The influence of Hf additions on the glass-forming ability (GFA), phase formation and mechanical properties of Cu50HfxZr50-x (x = 2,5,10,20 at.%) alloys has been systematically investigated. We report on a distinct correlation between phase formation and GFA of Cu50Zr50-based alloys. Increasing additions of Hf reduce the thermal stability of the high-temperature B2 Cu(Hf,Zr) phase, while the thermal stability of the corresponding undercooled melt is enhanced. The GFA of these alloy series gradually raises up to 10 at.% Hf, whereas at 20 at.%Hf, the GFA is drastically lowered, since the B2 Cu(Hf,Zr) phase becomes unstable and the precipitation of the low-temperature equilibrium phases is favoured. This interrelation determines the microstructure and results in the formation of Cu-Hf-Zr-based bulk metallic glass composites. These composites not only show appreciable macroscopic plastic strain, but also high yield strength.