2014, Burghoorn, M., Kniknie, B., van Deelen, J., Xu, M., Vroon, Z., van Ee, R., van de Belt, R., Buskens, P.

Textured transparent conductors are widely used in thin-film silicon solar cells. They lower the reflectivity at interfaces between different layers in the cell and/or cause an increase in the path length of photons in the Si absorber layer, which both result in an increase in the number of absorbed photons and, consequently, an increase in short-circuit current density (Jsc) and cell efficiency. Through optical simulations, we recently obtained strong indications that texturing of the transparent conductor in copper indium gallium (di-)selenide (CIGS) solar cells is also optically advantageous. Here, we experimentally demonstrate that the Jsc and efficiency of CIGS solar cells with an absorber layer thickness (dCIGS) of 0.85 μm, 1.00 μm and 2.00 μm increase through application of a moth-eye textured resist with a refractive index that is sufficiently similar to AZO (nresist = 1.792 vs. nAZO = 1.913-at 633 nm) to avoid large optical losses at the resist-AZO interface. On average, Jsc increases by 7.2%, which matches the average reduction in reflection of 7.0%. The average relative increase in efficiency is slightly lower (6.0%). No trend towards a larger relative increase in Jsc with decreasing dCIGS was observed. Ergo, the increase in Jsc can be fully explained by the reduction in reflection, and we did not observe any increase in Jsc based on an increased photon path length. © 2014 Author(s).

2014, Kasten, Annika, Naser, Tamara, Brüllhoff, Kristina, Fiedler, Jörg, Müller, Petra, Möller, Martin, Rychly, Joachim, Groll, Jürgen, Brenner, Rolf E., Engler, Adam J.

Designing of implant surfaces using a suitable ligand for cell adhesion to stimulate specific biological responses of stem cells will boost the application of regenerative implants. For example, materials that facilitate rapid and guided migration of stem cells would promote tissue regeneration. When seeded on fibronectin (FN) that was homogeneously immmobilized to NCO-sP(EO-stat-PO), which otherwise prevents protein binding and cell adhesion, human mesenchymal stem cells (MSC) revealed a faster migration, increased spreading and a more rapid organization of different cellular components for cell adhesion on fibronectin than on a glass surface. To further explore, how a structural organization of FN controls the behavior of MSC, adhesive lines of FN with varying width between 10 µm and 80 µm and spacings between 5 µm and 20 µm that did not allow cell adhesion were generated. In dependance on both line width and gaps, cells formed adjacent cell contacts, were individually organized in lines, or bridged the lines. With decreasing sizes of FN lines, speed and directionality of cell migration increased, which correlated with organization of the actin cytoskeleton, size and shape of the nuclei as well as of focal adhesions. Together, defined FN lines and gaps enabled a fine tuning of the structural organization of cellular components and migration. Microstructured adhesive substrates can mimic the extracellular matrix in vivo and stimulate cellular mechanisms which play a role in tissue regeneration.

2014, Peter, Karin

[no abstract available]

2014, Böker, Alexander

[No abstract available]

2014, Wessling, M., Morcillo, L. Garrigós, Abdu, S.

Electro-convective vortices in ion concentration polarization under shear flow have been of practical relevance for desalination processes using electrodialysis. The phenomenon has been scientifically disregarded for decades, but is recently embraced by a growing fluid dynamics community due its complex superposition of multi-scale gradients in electrochemical potential and space charge interacting with emerging complex fluid momentum gradients. While the visualization, quantification and fundamental understanding of the often-chaotic fluid dynamics is evolving rapidly due to sophisticated simulations and experimentation, little is known whether these instabilities can be induced and affected by chemical topological heterogeneity in surface properties. In this letter, we report that polyelectrolyte layers applied as micropatterns on ion exchange membranes induce and facilitate the electro-osmotic fluid instabilities. The findings stimulate a variety of fundamental questions comparable to the complexity of today's turbulence research.

2014, Chattopadhyay, Subrata, Heine, Elisabeth, Keul, Helmut, Moeller, Martin

In this work, we report the antimicrobial efficacy of azetidinium functionalized polytetrahydrofurans in solution and their application in the preparation of non leaching, antimicrobial surfaces. The excellent antimicrobial efficacy of these water soluble polymers both in solution and on surfaces (>99.99%–100% bacterial growth inhibition) makes them excellent candidates for solving the hygiene related problems in the medical and hospital environment.

2014, Dittrich, Barbara, Möller, Martin

Die Entwicklung lokaler Drug-Delivery-Systeme im Rahmen des Verbundprojektes addressierte zwei häufige urologische Erkrankungen: die Überaktive Blase (OAB, overactive bladder) und das nicht-muskelinvasiven Blasenkarzinom (NMIBK). Die OAB besitzt mit einer Prävalenz von 17 % in den USA und Europa das Ausmaß einer Volkskrankheit. Aktuelle Ansätze zur intravesikalen lokalen Wirkstoffgabe beinhalten in der Regel die Einspülung von Wirkstofflösungen über einen Katheter in die Blase (Instillation). Hierbei werden z. B. Antimuskarinika gegen die Überaktive Blase (overactive bladder, OAB) oder ein Zytostatika zur Rezidiv- und Progressionsprophylaxe bei nicht-Muskel invasivem Blasenkarzinom (NMIBK) eingesetzt. Das Ziel des Teilvorhabens war die Entwicklung aktiver Mikrosphären und Filamente auf Polymerbasis zur lokalen Freisetzung von urologisch relevanten Wirkstoffen wie beispielsweise Trospiumchlorid oder Mitomycin C in die Blase. Durch die lokale Freisetzung sollen Nebenwirkungen, die bei einer systemischen Darreichung auftreten, vermieden bzw. minimiert werden. Es wurde ein skalierbares Herstellungsverfahren für die Herstellung der aktiven Mikrosphären entwickelt, ausgehend von der Mahlung und Dispersion der Wirkstoffpartikel in der Polymermatrix durch einen Naßmahlprozess, dem eigentlichen Herstellungsverfahren auf der Basis eines Emulsionsprozess und der anschließenden Aufarbeitung zu einem rieselfähigen Pulver durch das Verfahren der Sprühtrocknung. Das Freisetzungsverhalten der ausgewählten Polymermatrices wurde untersucht und eine Optimierung des Systems vorgenommen. Für die Indikation NMIBK wurde ein stark verkleinertes Filament-artiges Drug-Delivery-Systems entwickelt. Die entwickelten aktiven Mikrosphären konnten erfolgreich in das Gesamtsystem eingebaut werden und die entwickelten Drug-Delivery-Systeme wurden erfolgreich in den in-vitro und in-vivo Untersuchungen der Projektpartner angewendet.