3 results
Search Results
Now showing 1 - 3 of 3
- ItemMetal Plastic Hybrids: Optimisation in model experiments [Metall-Kunststoff-Verbunde: Modellversuche zur Optimierung](Weinheim : Wiley-VCH, 2019) Bräuer, M.; Edelmann, M.; Lehmann, D.; Tuschla, M.Metal plastic hybrids will become more important as components for lightweight constructions. It is reported about optimisation of making three layer hybrids consisted of a steel plate, an adhesion layer based of uretdione powder coating material and a flexible component polyurethane in model experiments. Hybrid formation is performed in a compression moulding process. The adhesion layer and the polyurethane are modified to increase the hybrid bond strength. Peel test are conducted to quantitatively characterize the bond strength and an apparent energy release rate is calculated based on the peel force. For hybrids with widths of 2 mm polyurethane stripes it is possible to increase the apparent energy release rate for about 30 % to 16 N/mm in comparison with a hybrid with unmodified components. These hybrids have the same high bond strength level as the strongest hybrids reported in literature. Concluding the optimisation results are discussed related to their relevancy for the interpretation of the adhesion mechanisms in the interface between adhesion layer and polyurethane. © 2019 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.
- ItemUltralow percolation threshold in polyamide 6.6/MWCNT composites(Barking : Elsevier, 2015) Krause, Beate; Boldt, Regine; Häußler, Liane; Pötschke, PetraWhen incorporating multiwalled carbon nanotubes (MWCNTs) synthesised by the aerosol-CVD method using different solvents into polyamide 6.6 (PA66) by melt mixing an ultralow electrical percolation threshold of 0.04. wt.% was found. This very low threshold was assigned to the specific characteristic of the MWCNTs for which a very high aspect ratio, a good dispersability in aqueous surfactant dispersions, and relatively low oxygen content near the surface were measured. The investigation of the composites by transmission electron microscopy on ultrathin cuts as well as by scanning electron microscopy combined with charge contrast imaging on compression moulded plates illustrated a good MWCNT dispersion within the PA66 matrix and that the very high aspect ratio of the nanotubes remained even after melt processing. Additionally, the thermal behaviour of the PA66 composites was investigated using differential scanning calorimetry (DSC) showing that the addition of only 0.05. wt.% MWCNT leads to an increase of the onset crystallization temperature of 11. K.
- ItemCellulose-carbon nanotube composite aerogels as novel thermoelectric materials(Amsterdam [u.a.] : Elsevier, 2018) Gnanaseelan, Minoj; Chen, Yian; Luo, Jinji; Krause, Beate; Pionteck, Jürgen; Pötschke, Petra; Qu, HaisongThermoelectric materials based on cellulose/carbon nanotube (CNT) nanocomposites have been developed by a facile approach and the effects of amount (2–10 wt%) and types of CNTs (single-walled carbon nanotubes (SWCNTs) and multi-walled carbon nanotubes (MWCNTs)) on the morphology (films and aerogels) and the thermoelectric properties of the nanocomposites have been investigated. Composite films based on SWCNTs showed significantly higher electrical conductivity (5 S/cm at 10 wt%) and Seebeck coefficient (47.2 μV/K at 10 wt%) compared to those based on MWCNTs (0.9 S/cm and 11 μV/K, respectively). Lyophilization, leading to development of aerogels with sub-micron sized pores, decreased the electrical conductivity for both types by one order of magnitude, but did not affect the Seebeck coefficient of MWCNT based nanocomposites. For SWCNT containing aerogels, higher Seebeck coefficients than for films were measured at 3 and 4 wt% but significantly lower values at higher loadings. CNT addition increased the thermal conductivity from 0.06 to 0.12 W/(m∙K) in the films, whereas the lyophilization significantly reduced it towards values between 0.01 and 0.09 W/(m∙K) for the aerogels. The maximum Seebeck coefficient, power factor, and ZT observed in this study are 49 μV/K for aerogels with 3 wt% SWCNTs, 1.1 μW/(m∙K2) for composite films with 10 wt% SWCNTs, and 7.4 × 10−4 for films with 8 wt% SWCNTs, respectively.