13 results
Search Results
Now showing 1 - 10 of 13
- ItemModeling of edge-emitting lasers based on tensile strained germanium microstrips(New York, NY : IEEE, 2015) Peschka, D.; Thomas, M.; Glitzky, A.; Nürnberg, R.; Gärtner, K.; Virgilio, M.; Guha, S.; Schroeder, T.; Capellini, G.; Koprucki, Th.In this paper, we present a thorough modeling of an edge-emitting laser based on strained germanium (Ge) microstrips. The full-band structure of the tensile strained Ge layer enters the calculation of optical properties. Material gain for strained Ge is used in the 2D simulation of the carrier transport and of the optical field within a cross section of the microstrips orthogonal to the optical cavity. We study optoelectronic properties of the device for two different designs. The simulation results are very promising as they show feasible ways toward Ge emitter devices with lower threshold currents and higher efficiency as published insofar.
- ItemOptimizing Vertical and Lateral Waveguides of kW-Class Laser Bars for Higher Peak Power, Efficiency and Lateral Beam Quality(New York, NY : IEEE, 2022) Miah, M. Jarez; Boni, Anisuzzaman; Arslan, Seval; Martin, Dominik; Casa, Pietro Della; Crump, PaulGaAs-based, highly-efficient, kW-class, 1-cm laser bars with high peak power P opt and improved beam quality in quasi-continuous-wave mode are presented. The use of an extreme-triple-asymmetric (ETAS) epitaxial layer structure diminishes power saturation of high-power bars at high driving current. The resulting ETAS bars with 4 mm cavity produce a record 1.9 kW peak power, limited by available current supply, with a maximum power conversion efficiency η E = 67% at T HS = 25 °C heat-sink temperature. Both P opt and η E have been increased further by operating the bars at T HS = −70 °C. Sub-zero operation raises the P opt to 2.3 kW and the maximum η E to 74%. A second configuration of ETAS bars with optimized lateral layout is further realized to obtain narrow lateral beam divergence θ up to 2 kA driving current, without sacrificing P opt and η E . A 2–3° lower θ (95% power level) is observed over a wide operating range at room temperature. A high degree of polarization is also maintained across the whole operatingrange.
- Item60% Efficient Monolithically Wavelength-Stabilized 970-nm DBR Broad-Area Lasers(New York, NY : IEEE, 2022) Crump, Paul; Miah, M. Jarez; Wilkens, Martin; Fricke, Jorg; Wenzel, Hans; Knigge, AndreaProgress in epitaxial design is shown to enable increased optical output power P opt and power conversion efficiency η E and decreased lateral far-field divergence angle in GaAs-based distributed Bragg reflector (DBR) broad-area (BA) diode lasers. We show that the wavelength-locked power can be significantly increased (saturation at high bias current is mitigated) by migrating from an asymmetric large optical cavity (ASLOC) based laser structure to a highly asymmetric (extreme-triple-asymmetric (ETAS)) layer design. For wavelength-stabilization, 7 th order, monolithic DBRs are etched on the surface of fully grown epitaxial layer structures. The investigated ETAS reference Fabry-Pérot (FP) BA lasers without DBRs and with 200 µm stripe width and 4 mm cavity length provide P opt = 29 W (still increasing) at 30 A in continuous-wave mode at room temperature, in contrast to the maximum P opt = 24 W (limited by strong power saturation) of baseline ASLOC lasers. The reference ETAS FP lasers also deliver over 10% higher η E at P opt = 24 W. On the other hand, in comparison to the wavelength-stabilized ASLOC DBR lasers, ETAS DBR lasers show a peak power increment from 14 W to 22 W, and an efficiency increment from 46% to 60% at P opt = 14 W. A narrow spectral width (< 1 nm at 95% power content) is maintained across a very wide operating range. Consistent with earlier studies, a narrower far-field divergence angle and consequently an improved beam-parameter product is also observed, compared to the ASLOC-based lasers.
- ItemCalculation of the steady states in dynamic semiconductor laser models(Dordrecht [u.a.] : Springer Science + Business Media B.V, 2022) Radziunas, MindaugasWe discuss numerical challenges in calculating stable and unstable steady states of widely used dynamic semiconductor laser models. Knowledge of these states is valuable when analyzing laser dynamics and different properties of the lasing states. The example simulations and analysis mainly rely on 1(time)+1(space)-dimensional traveling-wave models, where the steady state defining conditions are formulated as a system of nonlinear algebraic equations. The performed steady state calculations reveal limitations of the Lang-Kobayashi model, explain nontrivial bias threshold relations in lasers with several electrical contacts, or predict and explain transient dynamics when simulating such lasers.
- ItemHigh-spectral-resolution terahertz imaging with a quantum-cascade laser(Washington, DC : Optical Society of America, 2016) Hagelschuer, Till; Rothbart, Nick; Richter, Heiko; Wienold, Martin; Schrottke, Lutz; Grahn, Holger T.; Hübers, Heinz-WilhelmWe report on a high-spectral-resolution terahertz imaging system operating with a multi-mode quantum-cascade laser (QCL), a fast scanning mirror, and a sensitive Ge:Ga detector. By tuning the frequency of the QCL, several spectra can be recorded in 1.5 s during the scan through a gas cell filled with methanol (CH3OH). These experiments yield information about the local absorption and the linewidth. Measurements with a faster frame rate of up to 3 Hz allow for the dynamic observation of CH3OH gas leaking from a terahertz-transparent tube into the evacuated cell. In addition to the relative absorption, the local pressure is mapped by exploiting the effect of pressure broadening.
- ItemReal-time gas sensing based on optical feedback in a terahertz quantum-cascade laser(Washington, DC : Optical Society of America, 2017) Hagelschuer, Till; Wienold, Martin; Richter, Heiko; Schrottke, Lutz; Grahn, Holger T.; Hübers, Heinz-WilhelmWe report on real-time gas sensing with a terahertz quantum-cascade laser (QCL). The method is solely based on the modulation of the external cavity length, exploiting the intermediate optical feedback regime. While the QCL is operated in continuous-wave mode, optical feedback results in a change of the QCL frequency as well as its terminal voltage. The first effect is exploited to tune the lasing frequency across a molecular absorption line. The second effect is used for the detection of the self-mixing signal. This allows for fast measurement times on the order of 10 ms per spectrum and for real-time measurements of gas concentrations with a rate of 100 Hz. This technique is demonstrated with a mixture of D2O and CH3OD in an absorption cell.
- ItemA compact, continuous-wave terahertz source based on a quantum-cascade laser and a miniature cryocooler(Washington, DC : Optical Society of America, 2010) Richter, H.; Greiner-Bär, M.; Pavlov, S.G.; Semenov, A.D.; Wienold, M.; Schrottke, L.; Giehler, M.; Hey, R.; Grahn, H.T.; Hübers, H.-W.We report on the development of a compact, easy-to-use terahertz radiation source, which combines a quantum-cascade laser (QCL) operating at 3.1 THz with a compact, low-input-power Stirling cooler. The QCL, which is based on a two-miniband design, has been developed for high output and low electrical pump power. The amount of generated heat complies with the nominal cooling capacity of the Stirling cooler of 7 W at 65 K with 240 W of electrical input power. Special care has been taken to achieve a good thermal coupling between the QCL and the cold finger of the cooler. The whole system weighs less than 15 kg including the cooler and power supplies. The maximum output power is 8 mW at 3.1 THz. With an appropriate optical beam shaping, the emission profile of the laser is fundamental Gaussian. The applicability of the system is demonstrated by imaging and molecular-spectroscopy experiments.
- ItemTerahertz quantum-cascade lasers as high-power and wideband, gapless sources for spectroscopy(Washington, DC : Optical Society of America, 2017) Röben, Benjamin; Lü, Xiang; Hempel, Martin; Biermann, Klaus; Schrottke, Lutz; Grahn, Holger T.Terahertz (THz) quantum-cascade lasers (QCLs) are powerful radiation sources for high-resolution and high-sensitivity spectroscopy with a discrete spectrum between 2 and 5 THz as well as a continuous coverage of several GHz. However, for many applications, a radiation source with a continuous coverage of a substantially larger frequency range is required. We employed a multi-mode THz QCL operated with a fast ramped injection current, which leads to a collective tuning of equally-spaced Fabry-Pérot laser modes exceeding their separation. A continuous coverage over 72 GHz at about 4.7 THz was achieved. We demonstrate that the QCL is superior to conventional sources used in Fourier transform infrared spectroscopy in terms of the signal-to-noise ratio as well as the dynamic range by one to two orders of magnitude. Our results pave the way for versatile THz spectroscopic systems with unprecedented resolution and sensitivity across a wide frequency range.
- ItemEvidence for frequency comb emission from a Fabry-Pérot terahertz quantum-cascade laser(Washington, DC : Optical Society of America, 2014) Wienold, M.; Röben, B.; Schrottke, L.; Grahn, H.T.We report on a broad-band terahertz quantum-cascade laser (QCL) with a long Fabry-Pérot ridge cavity, for which the tuning range of the individual laser modes exceeds the mode spacing. While a spectral range of approximately 60 GHz (2 cm−1) is continuously covered by current and temperature tuning, the total emission range spans more than 270 GHz (9 cm−1). Within certain operating ranges, we found evidence for stable frequency comb operation of the QCL. An experimental technique is presented to characterize frequency comb operation, which is based on the self-mixing effect.
- ItemHigh-temperature, continuous-wave operation of terahertz quantum-cascade lasers with metal-metal waveguides and third-order distributed feedback(Washington, DC : Optical Society of America, 2014) Wienold, M.; Röben, B.; Schrottke, L.; Sharma, R.; Tahraoui, A.; Biermann, K.; Grahn, H.T.Currently, different competing waveguide and resonator concepts exist for terahertz quantum-cascade lasers (THz QCLs). We examine the continuous-wave (cw) performance of THz QCLs with single-plasmon (SP) and metal-metal (MM) waveguides fabricated from the same wafer. While SP QCLs are superior in terms of output power, the maximum operating temperature for MM QCLs is typically much higher. For SP QCLs, we observed cw operation up to 73 K as compared to 129 K for narrow (≤ 15 μm) MM QCLs. In the latter case, single-mode operation and a narrow beam profile were achieved by applying third-order distributed-feedback gratings and contact pads which are optically insulated from the intended resonators. We present a quantitative analytic model for the beam profile, which is based on experimentally accessible parameters.