3 results
Search Results
Now showing 1 - 3 of 3
- ItemModeling of edge-emitting lasers based on tensile strained germanium microstrips(New York, NY : IEEE, 2015) Peschka, D.; Thomas, M.; Glitzky, A.; Nürnberg, R.; Gärtner, K.; Virgilio, M.; Guha, S.; Schroeder, T.; Capellini, G.; Koprucki, Th.In this paper, we present a thorough modeling of an edge-emitting laser based on strained germanium (Ge) microstrips. The full-band structure of the tensile strained Ge layer enters the calculation of optical properties. Material gain for strained Ge is used in the 2D simulation of the carrier transport and of the optical field within a cross section of the microstrips orthogonal to the optical cavity. We study optoelectronic properties of the device for two different designs. The simulation results are very promising as they show feasible ways toward Ge emitter devices with lower threshold currents and higher efficiency as published insofar.
- ItemOptimizing Vertical and Lateral Waveguides of kW-Class Laser Bars for Higher Peak Power, Efficiency and Lateral Beam Quality(New York, NY : IEEE, 2022) Miah, M. Jarez; Boni, Anisuzzaman; Arslan, Seval; Martin, Dominik; Casa, Pietro Della; Crump, PaulGaAs-based, highly-efficient, kW-class, 1-cm laser bars with high peak power P opt and improved beam quality in quasi-continuous-wave mode are presented. The use of an extreme-triple-asymmetric (ETAS) epitaxial layer structure diminishes power saturation of high-power bars at high driving current. The resulting ETAS bars with 4 mm cavity produce a record 1.9 kW peak power, limited by available current supply, with a maximum power conversion efficiency η E = 67% at T HS = 25 °C heat-sink temperature. Both P opt and η E have been increased further by operating the bars at T HS = −70 °C. Sub-zero operation raises the P opt to 2.3 kW and the maximum η E to 74%. A second configuration of ETAS bars with optimized lateral layout is further realized to obtain narrow lateral beam divergence θ up to 2 kA driving current, without sacrificing P opt and η E . A 2–3° lower θ (95% power level) is observed over a wide operating range at room temperature. A high degree of polarization is also maintained across the whole operatingrange.
- Item60% Efficient Monolithically Wavelength-Stabilized 970-nm DBR Broad-Area Lasers(New York, NY : IEEE, 2022) Crump, Paul; Miah, M. Jarez; Wilkens, Martin; Fricke, Jorg; Wenzel, Hans; Knigge, AndreaProgress in epitaxial design is shown to enable increased optical output power P opt and power conversion efficiency η E and decreased lateral far-field divergence angle in GaAs-based distributed Bragg reflector (DBR) broad-area (BA) diode lasers. We show that the wavelength-locked power can be significantly increased (saturation at high bias current is mitigated) by migrating from an asymmetric large optical cavity (ASLOC) based laser structure to a highly asymmetric (extreme-triple-asymmetric (ETAS)) layer design. For wavelength-stabilization, 7 th order, monolithic DBRs are etched on the surface of fully grown epitaxial layer structures. The investigated ETAS reference Fabry-Pérot (FP) BA lasers without DBRs and with 200 µm stripe width and 4 mm cavity length provide P opt = 29 W (still increasing) at 30 A in continuous-wave mode at room temperature, in contrast to the maximum P opt = 24 W (limited by strong power saturation) of baseline ASLOC lasers. The reference ETAS FP lasers also deliver over 10% higher η E at P opt = 24 W. On the other hand, in comparison to the wavelength-stabilized ASLOC DBR lasers, ETAS DBR lasers show a peak power increment from 14 W to 22 W, and an efficiency increment from 46% to 60% at P opt = 14 W. A narrow spectral width (< 1 nm at 95% power content) is maintained across a very wide operating range. Consistent with earlier studies, a narrower far-field divergence angle and consequently an improved beam-parameter product is also observed, compared to the ASLOC-based lasers.