Search Results
A Facile Chemical Method Enabling Uniform Zn Deposition for Improved Aqueous Zn-Ion Batteries
Rechargeable aqueous Zn-ion batteries (ZIBs) have gained great attention due to their high safety and the natural abundance of Zn. Unfortunately, the Zn metal anode suffers from dendrite growth due to nonuniform deposition during the plating/stripping process, leading to a sudden failure of the batteries. Herein, Cu coated Zn (Cu–Zn) was prepared by a facile pretreatment method using CuSO4 aqueous solution. The Cu coating transformed into an alloy interfacial layer with a high affinity for Zn, which acted as a nucleation site to guide the uniform Zn nucleation and plating. As a result, Cu–Zn demonstrated a cycling life of up to 1600 h in the symmetric cells and endowed a stable cycling performance with a capacity of 207 mAh g−1 even after 1000 cycles in the full cells coupled with a V2O5-based cathode. This work provides a simple and effective strategy to enable uniform Zn deposition for improved ZIBs.
Influence of Processing Parameters on Fibre Properties during Twin-Screw Extrusion of Poplar Wood Chips
For sustainable agriculture, the contentious input of peat in growing media needs to be replaced by a substitute with the best possible water-holding capacity (WHC). Wood from fast growing poplar trees, cultivated in short rotation coppices (SRC), is a suitable alternative if it is processed correctly in a twin-screw extruder. The processing parameters, such as the aperture setting of the extruder, moisture content, and specific energy demand (SED), during twin-screw extrusion, as well as their influence on fibre properties such as WHC and particle size distribution, are investigated. SRC-poplar wood chips from clone Max3 are the raw material used for this research. As a result, the best volume-based WHC (75%) at −1 kPa suction tension was achieved for dry extruded wood chip fibre at an aperture setting of 15 mm and an SED of 340 kWh*t−1. The smallest SED of 140 kWh*t−1 was measured at apertures of 35 mm and 40 mm, which resulted in a volume-based WHC of approximately 30% and a dry matter mass flow during processing of 0.289 t*h−1 (40 mm). The particle size distribution of semi-dry wood chips has the highest fine fraction as well as the smallest coarse fraction. Conclusively, poplar wood can be processed fresh and dry into fibre at an acceptable SED, which results in an acceptable WHC.
Through the Window: Exploitation and Countermeasures of the ESP32 Register Window Overflow †
With the increasing popularity of IoT (Internet-of-Things) devices, their security becomes an increasingly important issue. Buffer overflow vulnerabilities have been known for decades, but are still relevant, especially for embedded devices where certain security measures cannot be implemented due to hardware restrictions or simply due to their impact on performance. Therefore, many buffer overflow detection mechanisms check for overflows only before critical data are used. All data that an attacker could use for his own purposes can be considered critical. It is, therefore, essential that all critical data are checked between writing a buffer and its usage. This paper presents a vulnerability of the ESP32 microcontroller, used in millions of IoT devices, that is based on a pointer that is not protected by classic buffer overflow detection mechanisms such as Stack Canaries or Shadow Stacks. This paper discusses the implications of vulnerability and presents mitigation techniques, including a patch, that fixes the vulnerability. The overhead of the patch is evaluated using simulation as well as an ESP32-WROVER-E development board. We showed that, in the simulation with 32 general-purpose registers, the overhead for the CoreMark benchmark ranges between 0.1% and 0.4%. On the ESP32, which uses an Xtensa LX6 core with 64 general-purpose registers, the overhead went down to below 0.01%. A worst-case scenario, modeled by a synthetic benchmark, showed overheads up to 9.68%.
DNA-Biofunctionalization of CTAC-Capped Gold Nanocubes
Clinical diagnostics and disease control are fields that strongly depend on technologies for rapid, sensitive, and selective detection of biological or chemical analytes. Nanoparticles have become an integral part in various biomedical detection devices and nanotherapeutics. An increasing focus is laid on gold nanoparticles as they express less cytotoxicity, high stability, and hold unique optical properties with the ability of signal transduction of biological recognition events with enhanced analytical performance. Strong electromagnetic field enhancements can be found in close proximity to the nanoparticle that can be exploited to enhance signals for e.g., metal-enhanced fluorescence or Raman spectroscopy. Even stronger field enhancements can be achieved with sharp-edged nanoparticles, which are synthesized with the help of facet blocking agents, such as cetyltrimethylammonium bromide/chloride (CTAB/CTAC). However, chemical modification of the nanoparticle surface is necessary to reduce the particle’s cytotoxicity, stabilize it against aggregation, and to bioconjugate it with biomolecules to increase its biocompatibility and/or specificity for analytical applications. Here, a reliable two-step protocol following a ligand exchange with bis (p-sulfonatophenyl) phenyl phosphine (BSPP) as the intermediate capping-agent is demonstrated, which results in the reliable biofunctionalization of CTAC-capped gold nanocubes with thiol-modified DNA. The functionalized nanocubes have been characterized regarding their electric potential, plasmonic properties, and stability against high concentrations of NaCl and MgCl2.
Effect of Build Orientation on the Microstructure, Mechanical and Corrosion Properties of a Biodegradable High Manganese Steel Processed by Laser Powder Bed Fusion
In the last decade, additive manufacturing technologies like laser powder bed fusion (LPBF) have emerged strongly. However, the process characteristics involving layer-wise build-up of the part and the occurring high, directional thermal gradient result in significant changes of the microstructure and the related properties compared to traditionally fabricated materials. This study presents the influence of the build direction (BD) on the microstructure and resulting properties of a novel austenitic Fe-30Mn-1C-0.02S alloy processed via LPBF. The fabricated samples display a {011} texture in BD which was detected by electron backscatter diffraction. Furthermore, isolated binding defects could be observed between the layers. Quasi-static tensile and compression tests displayed that the yield, ultimate tensile as well as the compressive yield strength are significantly higher for samples which were built with their longitudinal axis perpendicular to BD compared to their parallel counterparts. This was predominantly ascribed to the less severe effects of the sharp-edged binding defects loaded perpendicular to BD. Additionally, a change of the Young’s modulus in dependence of BD could be demonstrated, which is explained by the respective texture. Potentiodynamic polarization tests conducted in a simulated body fluid revealed only slight differences of the corrosion properties in dependence of the build design.
Development of Biorefineries in the Bioeconomy: A Fuzzy-Set Qualitative Comparative Analysis among European Countries
This study aims to identify the configurational conditions that characterize the establish-ment of biorefineries in 20 European countries. After determining the conditions which support a bioeconomy transition, secondary data from national sources are used to represent their existing conditions within respective countries. Then, a fuzzy-set qualitative comparative analysis is em-ployed to compare and contrast the effect of varying combinations of the selected conditions on the development of biorefineries. The conditions chosen include coherent bioeconomy strategies, network intensity of regional bioclusters, intellectual capital, and natural resource availability. Our results reveal that the configuration of a coherent bioeconomy strategy, sizable public spending on R&D, abundant biomass supply, and a high level of network intensity is sufficient to explain the pro-nounced biorefineries development among some European countries. We recommend that countries with fragmented approaches review and redesign the policy and regulatory framework to create a holistic and consistent bioeconomy strategy, taking into account the configurations of conditions as an important prerequisite. In particular, factors such as the lack of best practice examples, the low level of public spending on research and development, the economic capacities for a skilled workforce in addition to the sustainable supply of raw materials should be addressed as focal points.
Investigating Solid and Liquid Desiccant Dehumidification Options for Room Air-Conditioning and Drying Applications
This study reports on the investigation of the performance of single and two-stage liquid and solid desiccant dehumidification systems and two-stage combined liquid and solid desiccant dehumidification systems with reference to humid climates. The research focus is on a dehumidification system capacity of 25 kW designed for room air conditioning application using the thermal models reported in the literature. RD-type silica gel and LiCl are used as solid and liquid desiccant materials, respectively. In this study, the application of proposed system for deep drying application is also explored. Condensation rate and moisture removal efficiency are chosen as performance parameters for room air conditioning application, whereas air outlet temperature is chosen as performance parameter for deep drying application. Further, for a given range of operating parameters, influences of air inlet humidity ratio, flow rate, and inlet temperature on performance parameters of the systems are investigated. In humid climatic conditions, it has been observed that a two-stage liquid desiccant dehumidification system is more effective for room air conditioning application, and two-stage solid desiccant dehumidification system is more suitable for deep drying application in the temperature range of 50 to 70 °C, while single-stage solid desiccant and two-stage combined liquid and solid desiccant dehumidification systems are more effective for low temperature, i.e., 30 to 50 °C deep drying application.
Aluminum-Doped Zinc Oxide Improved by Silver Nanowires for Flexible, Semitransparent and Conductive Electrodes on Textile with High Temperature Stability
In order to facilitate the design freedom for the implementation of textile-integrated electronics, we seek flexible transparent conductive electrodes (TCEs) that can withstand not only the mechanical stresses encountered during use but also the thermal stresses of post-treatment. The transparent conductive oxides (TCO) typically used for this purpose are rigid in comparison to the fibers or textiles they are intended to coat. In this paper, a TCO, specifically aluminum-doped zinc oxide (Al:ZnO), is combined with an underlying layer of silver nanowires (Ag-NW). This combination brings together the advantages of a closed, conductive Al:ZnO layer and a flexible Ag-NW layer, forming a TCE. The result is a transparency of 20–25% (within the 400–800 nm range) and a sheet resistance of 10 Ω/sq that remains almost unchanged, even after post-treatment at 180 °C.
Estimation of Vegetative Growth in Strawberry Plants Using Mobile LiDAR Laser Scanner
Monitoring of plant vegetative growth can provide the basis for precise crop manage-ment. In this study, a 2D light detection and ranging (LiDAR) laser scanner, mounted on a linear conveyor, was used to acquire multi-temporal three-dimensional (3D) data from strawberry plants (‘Honeoye’ and ‘Malling Centenary’) 14–77 days after planting (DAP). Canopy geometrical variables, i.e., points per plant, height, ground projected area, and canopy volume profile, were extracted from 3D point cloud. The manually measured leaf area exhibited a linear relationship with LiDAR-derived parameters (R2 = 0.98, 0.90, 0.93, and 0.96 with number of points per plant, volume, height, and projected canopy area, respectively). However, the measuring uncertainty was high in the dense canopies. Particularly, the canopy volume estimation was adapted to the plant habitus to remove gaps and empty spaces in the canopy point cloud. The parametric values for maximum point to point distance (Dmax) = 0.15 cm and slice height (S) = 0.10 cm resulted in R2 = 0.80 and RMSPE = 26.93% for strawberry plant volume estimation considering actual volume measured by water displacement. The vertical volume profiling provided growth data for cultivars ‘Honeoye’ and ‘Malling Centenary’ being 51.36 cm3 at 77 DAP and 42.18 cm3 at 70 DAP, respectively. The results contribute an approach for estimating plant geometrical features and particularly strawberry canopy volume profile based on LiDAR point cloud for tracking plant growth.
Passive Detection and Imaging of Human Body Radiation Using an Uncooled Field-Effect Transistor-Based THz Detector
This work presents, to our knowledge, the first completely passive imaging with human-body-emitted radiation in the lower THz frequency range using a broadband uncooled detector. The sensor consists of a Si CMOS field-effect transistor with an integrated log-spiral THz antenna. This THz sensor was measured to exhibit a rather flat responsivity over the 0.1–1.5-THz frequency range, with values√ of the optical responsivity and noise-equivalent power of around 40 mA/W and 42 pW/ Hz, respectively. These values are in good agreement with simulations which suggest an even broader flat responsivity range exceeding 2.0 THz. The successful imaging demonstrates the impressive thermal sensitivity which can be achieved with such a sensor. Recording of a 2.3 × 7.5-cm2-sized image of the fingers of a hand with a pixel size of 1 mm2 at a scanning speed of 1 mm/s leads to a signal-to-noise ratio of 2 and a noise-equivalent temperature difference of 4.4 K. This approach shows a new sensing approach with field-effect transistors as THz detectors which are usually used for active THz detection. © 2020 by the authors. Licensee MDPI, Basel, Switzerland.