Filters

2020 - 20243

More filters

2021 - 20243
Reset filters

Settings

Subject: High-entropy alloy ×

Search Results

Now showing 1 - 3 of 3
  • Thumbnail Image
    Item
    Microstructure, Texture, and Strength Development during High-Pressure Torsion of CrMnFeCoNi High-Entropy Alloy
    (Basel : MDPI, 2020) Skrotzki, Werner; Pukenas, Aurimas; Odor, Eva; Joni, Bertalan; Ungar, Tamas; Völker, Bernhard; Hohenwarter, Anton; Pippan, Reinhard; George, Easo P.
    The equiatomic face-centered cubic high-entropy alloy CrMnFeCoNi was severely deformed at room and liquid nitrogen temperature by high-pressure torsion up to shear strains of about 170. Itsmicrostructurewas analyzed by X-ray line profile analysis and transmission electronmicroscopy and its texture by X-ray microdiffraction. Microhardness measurements, after severe plastic deformation, were done at room temperature. It is shown that at a shear strain of about 20, a steady state grain size of 24 nm, and a dislocation density of the order of 1016 m-2 is reached. The dislocations are mainly screw-type with low dipole character. Mechanical twinning at room temperature is replaced by a martensitic phase transformation at 77 K. The texture developed at room temperature is typical for sheared face-centered cubic nanocrystalline metals, but it is extremely weak and becomes almost random after high-pressure torsion at 77 K. The strength of the nanocrystalline material produced by high-pressure torsion at 77 K is lower than that produced at room temperature. The results are discussed in terms of different mechanisms of deformation, including dislocation generation and propagation, twinning, grain boundary sliding, and phase transformation. © 2020 by the authors. Licensee MDPI, Basel, Switzerland.
  • Thumbnail Image
    Item
    Effect of Stacking Fault Energy on Microstructure and Texture Evolution during the Rolling of Non-Equiatomic CrMnFeCoNi High-Entropy Alloys
    (Basel : MDPI, 2020) Dan Sathiaraj, G.; Kalsar, Rajib; Suwas, Satyam; Skrotzki, Werner
    The evolution of microstructure and texture in three non-equiatomic CrMnFeCoNi high-entropy alloys (HEAs) with varying stacking fault energy (SFE) has been studied in up to 90% rolling reductions at both room and cryogenic temperature. All the HEAs deform by dislocation slip and additional mechanical twinning at intermediate and shear banding at high rolling strains. The microstructure is quite heterogeneous and, with strain, becomes highly fragmented. During rolling, a characteristic brass-type texture develops. Its strength increases with a decreasing SFE and the lowering of the rolling temperature. The texture evolution is discussed with regard to planar slip, mechanical twinning, and shear banding. © 2020 by the authors. Licensee MDPI, Basel, Switzerland.
  • Thumbnail Image
    Item
    Laser powder bed fusion of Fe60(CoCrNiMn)40 medium-entropy alloy with excellent strength-ductility balance
    (Amsterdam [u.a.] : Elsevier Science, 2024) Yang, Shengze; Liu, Yang; Chen, Hongyu; Wang, Yonggang; Kosiba, Konrad
    In this study, Fe60(CoCrNiMn)40 medium-entropy alloy (MEA) was fabricated by laser powder bed fusion (LPBF) via mixing of pure Fe and FeCoCrNiMn powders, the processability, microstructure and mechanical properties were systematically investigated, and the mechanism of strengthening and toughening were revealed through combination of experiments and molecular dynamics (MD) simulations. Results show that fraction of BCC phase decreased gradually with increasing volume energy density (VED), and thus heterostructue with varying FCC and BCC phases were produced through regulating the VED. The Fe60(CoCrNiMn)40 MEA (with scanning speeds of 700 and 800 mm/s) showed excellent strength-plasticity balance (e.g. 476 MPa, 612 MPa and 63 %) compared to the equiatomic FeCoCrNiMn HEA, which is ascribed to the synergistic strengthening and toughening effects involving the twinning induced plasticity (TWIP) and the reinforcement caused by the BCC phase (act as reinforced particle) embedded in the FCC matrix.