5 results
Search Results
Now showing 1 - 5 of 5
- ItemInfluence of microwave plasma treatment on the surface properties of carbon fibers and their adhesion in a polypropylene matrix(London [u.a.] : Institute of Physics, 2016) Scheffler, C.; Wölfel, E.; Förster, T.; Poitzsch, C.; Kotte, L.; Mäder, G.; Madsen, Bo; Biel, A.; Kusano, Y.; Lilholt, H.; Mikkelsen, L.P.; Mishnaevsky Jr., L.; Sørensen, B.F.A commercially available carbon fiber (CF) with an epoxy-based sizing (EP-sized CF) and an unsized CF have been plasma treated to study the effect on the fiber-matrix adhesion towards a polypropylene matrix. The EP-sized fiber was chosen because of its predictable low adhesion in a polypropylene (PP) matrix. The fibers have been modified using a microwave low-pressure O2/CO2/N2-gas plasma source (Cyrannus®) developed at IWS in a batch process. One aim of this study was the evaluation of parameters using high energies and short time periods in the plasma chamber to see the effect on mechanical performance of CF. These results will be the fundamental work for a planned continuous plasma modification line. The CF surface was characterized by determining the surface energies, single fiber tensile strength and XPS analysis. The adhesion behavior before and after plasma treatment was studied by single fiber pull-out test (SFPO) and scanning electron microscopy (SEM). It was shown that the CO2- and O2-plasma increases the number of functional groups on the fiber surface during short time plasma treatment of 30 s. Carboxylic groups on the unsized CF surface resulting from O2-plasma treatment lead to an enhanced fiber-matrix adhesion, whereas the fiber strength was merely reduced.
- ItemPolyester textile functionalization through incorporation of pH/thermo-responsive microgels. Part II: Polyester functionalization and characterization(Heidelberg : Springer, 2012) Glampedaki, P.; Calvimontes, A.; Dutschk, V.; Warmoeskerken, M.M.C.G.A new approach to functionalize the surface of polyester textiles is described in this study. Functionalization was achieved by incorporating pH/temperature-responsive polyelectrolyte microgels into the textile surface layer using UV irradiation. The aim of functionalization was to regulate polyester wettability according to ambient conditions by imparting stimuli-responsiveness from the microgel to the textile itself. Microgels consisted of pH/thermo-responsive microparticles of poly(N-isopropylacrylamide- co-acrylic acid) either alone or complexed with the pH-responsive natural polysaccharide chitosan. Scanning Electron Microscopy, X-ray Photoelectron Spectroscopy, ζ-potential measurements, and topographical analysis were used for surface characterization. Wettability of polyester textiles was assessed by dynamic wetting, water vapor transfer, and moisture regain measurements. One of the main findings showed that the polyester surface was rendered pH-responsive, both in acidic and alkaline pH region, owing to the microgel incorporation. With a marked relaxation in their structure and an increase in their microporosity, the functionalized textiles exhibited higher water vapor transfer rates both at 20 and 40 °C, and 65% relative humidity compared with the reference polyester. Also, at 40 °C, i.e., above the microgel Lower Critical Solution Temperature, the functionalized polyester textiles had lower moisture regains than the reference. Finally, the type of the incorporated microgel affected significantly the polyester total absorption times, with an up to 300% increase in one case and an up to 80% decrease in another case. These findings are promising for the development of functional textile materials with possible applications in biotechnology, technical, and protective clothing.
- ItemThermal conductivity of hybrid filled HDPE nanocomposites(Melville, NY : AIP, 2017) Müller, M. T.; Krause, Beate; Kretzschmar, B.; Jahn, I.; Pötschke, PetraIn this study composite materials based on high-density polyethylene (HDPE) with fillers containing nanostructures were prepared using melt mixing. Vapour Grown Carbon Fibers (VGCF), multiwalled carbon nanotubes (MWCNT) of the types Baytubes® C150P and Nanocyl™ NC7000, anthracite powder, microsilica, organoclay and expanded graphite (EG) as well as mixtures of these fillers were used. The amount and mixing ratios of the hybrid filled systems have been varied to determine their effects on the achievable level of thermal conductivity as measured on compression molded plates. The filler dispersion and phase adhesion were studied using scanning electron microscopy. When limiting the maximum filler content to 10 wt%, the highest enhancement in thermal conductivity by 166% was found for VGCF followed by a 1:1 filler combination of VGCF with EG (148%).
- ItemComparison of nano-structured transition metal modified tri-metal MgMAl–LDHs (M = Fe, Zn, Cu, Ni, Co) prepared using co-precipitation(Cambridge : RSC, 2019) Gevers, Bianca R.; Naseem, Sajid; Leuteritz, Andreas; Labuschagné, Frederick J. W. J.Comparison of layered double hydroxides (LDHs) synthesised using different methods, conditions and post-treatment is difficult to achieve because these greatly modify their material properties. This paper aims to provide a comparison of material properties for modified quintinite, where all LDHs were synthesised at the same conditions-thus allowing for direct comparison of the material properties obtained. Nano-structured materials were formed in all cases. The nano-structured transition metal (TM) MgMAl-LDHs were synthesised using constant pH co-precipitation. Five TMs (M = Fe, Co, Ni, Cu, Zn) were included in the LDH layers with molar substitutions of 0.5%, 1%, 5%, 10%, and 25% based on Mg-replacement for divalent TM cations and Al-replacement for trivalent TM cations. The materials were characterised using powder X-ray diffraction (XRD), X-ray fluorescence spectroscopy (XRF), scanning electron microscopy (SEM), attenuated total reflectance Fourier transform infrared analysis (ATR-FTIR), thermogravimetric analysis (TGA) and particle size analysis (PSA). The modified LDHs were synthesised free of major by-products and with similar morphologies. It could be shown that the crystallite dimensions varied between the different TM substitutions, that morphological changes were visible for some of the TMs used, that the processability depended on the TMs substituted, and that the substitution of TMs influenced the thermal stability of the LDHs. This journal is © 2019 The Royal Society of Chemistry.
- ItemComparison of transition metal (Fe, Co, Ni, Cu, and Zn) containing tri-metal layered double hydroxides (LDHs) prepared by urea hydrolysis(Cambridge : RSC, 2019) Naseem, Sajid; Gevers, Bianca; Boldt, Regine; Labuschagné, Frederick J. W. J.; Leuteritz, AndreasThis paper details a successful synthesis and comparison of a range of tri-metal hydrotalcite-like layered double hydroxides (LDHs) using urea hydrolysis. Transition-metal-substituted MgMAl-LDHs were synthesized with M = Fe, Co, Ni, Cu or Zn. 5 mol% and 10 mol% substitutions were performed, where Mg was substituted with Co, Ni, Cu and Zn, and Al with Fe. The successful synthesis of crystalline MgMAl-LDHs was confirmed using X-ray powder diffraction (XRD) analysis. Energy-dispersive X-ray (EDX) spectroscopy was used to identify substituted metals and determine changes in composition. Changes in morphology were studied using scanning electron microscopy (SEM). Thermogravimetric analysis was used to determine the effect of Fe-, Co-, Ni-, Cu- or Zn-substitution on the thermal degradation of the MgMAl-LDH phase. The structure, morphology and thermal behavior of the LDHs were shown to be influenced by the substituted transition metals. The observed thermal stability took the order MgNiAl- > MgFeAl- = MgAl- ≥ MgCoAl- > MgCuAl- > MgZnAl-LDH. The urea hydrolysis method was shown to be a simple preparation method for well-defined crystallite structures with large hexagonal platelets and good distribution of transition metal atoms in the substituted LDHs. © 2019 The Royal Society of Chemistry.