10 results
Search Results
Now showing 1 - 10 of 10
- ItemPredictability of properties of a fractured geothermal reservoir: the opportunities and limitations of an outcrop analogue study(Berlin ; Heidelberg [u.a.] : SpringerOpen, 2017) Bauer, Johanna F.; Krumbholz, Michael; Meier, Silke; Tanner, David C.Minimizing exploration risk in deep geothermics is of great economic importance. Especially, knowledge about temperature and permeability of the reservoir is essential. We test the potential of an outcrop analogue study to minimize uncertainties in prediction of the rock properties of a fractured reservoir in the Upper Rhine Graben. Our results show that although mineralogical composition, clay content, grain size, and fabric type are basically comparable, porosity and quartz cementation are not. Young’s modulus, as observed in the outcrop closest to the reservoir is about twice as high (~ 64 GPa) as observed in the reservoir (~ 34 GPa). Most importantly, however, the parameters that describe the fracture system, which are essential to predict reservoir permeability, differ significantly. While the outcrops are dominated by perpendicular fracture sets (striking NE–SW and NW–SE), two different conjugate fracture sets (striking NW–SE and N–S) occur in the reservoir. Fracture apertures, as reported from the FMI, are one order of magnitude wider than in the outcrop. We conclude that our outcrop analogue study fails to predict important properties of the reservoir (such as permeability and porosity). This must be in part because of the tectonically complex setting of the reservoir. We propose that analogue studies are important, but they must be treated with care when attempting to predict the controlling parameters of a fractured reservoir.
- ItemHigh‐resolution reflection seismics reveal the structure and the evolution of the Quaternary glacial Tannwald Basin(Oxford : Wiley, 2018) Burschil, Thomas; Buness, Hermann; Tanner, David C.; Wielandt‐Schuster, Ulrike; Ellwanger, Dietrich; Gabriel, GeraldOver-deepened basins exist throughout the Alpine realm. Improving our knowledge on these basins is of high social relevance, since these areas are often well-populated and they possess, for instance, unusual hydrological settings. Nonetheless, geophysical and sedimentological investigations of over-deepened basins are rare. We analyse the sedimentary succession of such a basin, the Tannwald Basin, through geological interpretation of seismic reflection profiles. The basin is located approximately 60 km north of the European Alps. It was incised into Tertiary molasse sediments by the Rhine Glacier and later filled by glacial, fluvial, and lacustrine deposits of 250 m thickness. The Leibniz Institute for Applied Geophysics acquired a grid of five high-resolution seismic reflection lines that imaged till the deepest parts of the Tannwald Basin. The seismic profiles, processed to a pre-stack depth migration level, allow a detailed geological interpretation that is calibrated with the help of a nearby borehole. We determine the structure and the seismic facies of the sediment succession in the basin and presume the following hypothesis of the evolution of the basin: sub-glacial erosion comprises the excavation of the over-deepened basin as well as detachment of large fragments of molasse material. These molasse slabs were deposited within the basin in a layer of basal till that graded upwards in water-lain till and fine-grained deposits. During the last two glaciations, the basinal structure became buried by till sequences and glacio-fluvial sediments.
- ItemStructural analysis of S-wave seismics around an urban sinkhole: evidence of enhanced dissolution in a strike-slip fault zone(Katlenburg-Lindau : European Geophysical Society, 2017-12-19) Wadas, Sonja H.; Tanner, David C.; Polom, Ulrich; Krawczyk, Charlotte M.In November 2010, a large sinkhole opened up in the urban area of Schmalkalden, Germany. To determine the key factors which benefited the development of this collapse structure and therefore the dissolution, we carried out several shear-wave reflection-seismic profiles around the sinkhole. In the seismic sections we see evidence of the Mesozoic tectonic movement in the form of a NW–SE striking, dextral strike-slip fault, known as the Heßleser Fault, which faulted and fractured the subsurface below the town. The strike-slip faulting created a zone of small blocks ( < 100 m in size), around which steep-dipping normal faults, reverse faults and a dense fracture network serve as fluid pathways for the artesian-confined groundwater. The faults also acted as barriers for horizontal groundwater flow perpendicular to the fault planes. Instead groundwater flows along the faults which serve as conduits and forms cavities in the Permian deposits below ca. 60 m depth. Mass movements and the resulting cavities lead to the formation of sinkholes and dissolution-induced depressions. Since the processes are still ongoing, the occurrence of a new sinkhole cannot be ruled out. This case study demonstrates how S-wave seismics can characterize a sinkhole and, together with geological information, can be used to study the processes that result in sinkhole formation, such as a near-surface fault zone located in soluble rocks. The more complex the fault geometry and interaction between faults, the more prone an area is to sinkhole occurrence.
- ItemMulti-stage emplacement of the Götemar Pluton, SE Sweden: new evidence inferred from field observations and microfabric analysis, including cathodoluminescence microscopy(Berlin ; Heidelberg : Springer, 2012) Friese, Nadine; Vollbrecht, Axel; Tanner, David C.; Fahlbusch, Wiebke; Weidemann, MiriamThe emplacement of the Mesoproterozoic Götemar Pluton into Paleoproterozoic granitoid host rocks of the Transscandinavian Igneous Belt is re-examined by microfabric analysis, including cathodoluminescence microscopy. Field data on the pluton-host rock system are used to strengthen the model. The Götemar Pluton, situated on the Baltic Shield of SE Sweden, is a horizontally zoned tabular structure that was constructed by the intrusion of successive pulses of magma with different crystal/melt ratios, at an estimated crustal depth of 4–8 km. Initial pluton formation involved magma ascent along a vertical dike, which was arrested at a mechanical discontinuity within the granitoid host rocks; this led to the formation of an initial sill. Subsequent sill stacking and their constant inflation resulted in deformation and reheating of existing magma bodies, which also raised the pluton roof. This multi-stage emplacement scenario is indicated by complex dike relationships and the occurrence of several generations of quartz (Si-metasomatism). The sills were charged by different domains of a heterogeneous magma chamber with varying crystal/melt ratios. Ascent or emplacement of magma with a high crystal/melt ratio is indicated by syn-magmatic deformation of phenocrysts. Complex crystallization fabrics (e.g. oscillatory growth zoning caused by high crystal defect density, overgrowth and replacement features, resorbed and corroded crystal cores, rapakivi structure) are mostly related to processes within the main chamber, that is repeated magma mixing or water influx.
- ItemNear-surface fault detection using high-resolution shear wave reflection seismics at the CO2CRC Otway Project site, Australia(Hoboken, NJ : Wiley, 2016) Beilecke, Thies; Krawczyk, Charlotte M.; Ziesch, Jennifer; Tanner, David C.High-resolution, near-surface, shear wave reflection seismic measurements were carried out in November 2013 at the CO2CRC Otway Project site, Victoria, Australia, with the aim to determine whether and, if so, where deeper faults reach the near subsurface. From a previous P wave 3-D reflection seismic data set that was concentrated on a reservoir at 2 km depth, we can only interpret faults up to 400 m below sea level. For the future monitoring in the overburden of the CO2 reservoir it is important to know whether and how the faults continue in the subsurface. We prove that two regional fault zones do in fact reach the surface instead of dying out at depth. Individual first-break signatures in the shot gathers along the profiles support this interpretation. However, this finding does not imply perforce communication between the reservoir and the surface in the framework of CO2 injection. The shear wave seismic sections are complementary to existing P wave volumes. They image with high resolution (better than 3 m vertically) different tectonic structures. Similar structures also outcrop on the southern coast of the Otway Basin. Both the seismic and the outcrops evidence the complex youngest structural history of the area.
- ItemInitiation and development of normal faults within the German alpine foreland basin: The inconspicuous role of basement structures(Hoboken, NJ : Wiley, 2016) Hartmann, Hartwig von; Tanner, David C.; Schumacher, SandraIn a large seismic cube within the German Alpine Molasse Basin, we recognize large normal faults with lateral alternating dips that displace the Molasse sediments. They are disconnected but strike parallel to fault lineaments of the underlying carbonate platform. This raises the question how such faults could independently develop. Structural analysis suggests that the faults grew both upward and downward from the middle of the Molasse package, i.e., they newly initiated within the Molasse sediments and were not caused by reactivation of the faults in the carbonate platform and/or crystalline basement. Numerical modeling of the basin proves that temporarily and spatially confined extensional stresses existed within the Molasse sediments but not in the carbonate platform and basement during lithospheric bending. The workflow shown here gives a new and as yet undocumented insight in the tectonic and structural processes within a foreland basin that was affected by buckling and bending in front of the orogen.
- ItemEvaluation of deep crustal earthquakes in northern Germany - Possible tectonic causes(Oxford [u.a.] : Wiley-Blackwell, 2019) Brandes, Christian; Plenefisch, Thomas; Tanner, David C.; Gestermann, Nicolai; Steffen, HolgerWe present new evidence for seven deep crustal, intraplate earthquakes in northern Germany, a region regarded as an area of low seismicity. From 2000 to 2018, seven earthquakes with magnitudes of ML 1.3–3.1, were detected at depths of 17.0–31.4 km. By placing the earthquake hypocentres in a geological three-dimensional model, we can correlate two of the earthquakes with the Thor Suture, a major fault zone in this area. Five of the earthquakes group in the lower crust near the Moho, which implies that parts of the lower crust and the crust/mantle boundary in northern Germany act as a structural discontinuity on which deformation localizes. Numerical simulation implies that stress changes due to glacial isostatic adjustment most likely triggered these deep crustal earthquakes.
- ItemA numerical sensitivity study of how permeability, porosity, geological structure, and hydraulic gradient control the lifetime of a geothermal reservoir(Göttingen : Copernicus Publ., 2019) Bauer, Johanna F.; Krumbholz, Michael; Luijendijk, Elco; Tanner, David C.Geothermal energy is an important and sustainable resource that has more potential than is currently utilized. Whether or not a deep geothermal resource can be exploited, mostly depends on, besides temperature, the utilizable reservoir volume over time, which in turn largely depends on petrophysical parameters. We show, using over 1000 (n=1027) 4-D finite-element models of a simple geothermal doublet, that the lifetime of a reservoir is a complex function of its geological parameters, their heterogeneity, and the background hydraulic gradient (BHG). In our models, we test the effects of porosity, permeability, and BHG in an isotropic medium. Furthermore, we simulate the effect of permeability contrast and anisotropy induced by layering, fractures, and a fault. We quantify the lifetime of the reservoir by measuring the time to thermal breakthrough, i.e. how many years pass before the temperature of the produced fluid falls below the 100 ∘C threshold. The results of our sensitivity study attest to the positive effect of high porosity; however, high permeability and BHG can combine to outperform the former. Particular configurations of all the parameters can cause either early thermal breakthrough or extreme longevity of the reservoir. For example, the presence of high-permeability fractures, e.g. in a fault damage zone, can provide initially high yields, but it channels fluid flow and therefore dramatically restricts the exploitable reservoir volume. We demonstrate that the magnitude and orientation of the BHG, provided permeability is sufficiently high, are the prime parameters that affect the lifetime of a reservoir. Our numerical experiments show also that BHGs (low and high) can be outperformed by comparatively small variations in permeability contrast (103) and fracture-induced permeability anisotropy (101) that thus strongly affect the performance of geothermal reservoirs.
- ItemVisualisation and analysis of shear-deformation bands in unconsolidated Pleistocene sand using ground-penetrating radar: Implications for paleoseismological studies(Amsterdam [u.a.] : Elsevier, 2018) Brandes, Christian; Igel, Jan; Loewer, Markus; Tanner, David C.; Lang, Jörg; Müller, Katharina; Winsemann, JuttaDeformation bands in unconsolidated sediments are of great value for paleoseismological studies in sedimentary archives. Using ground-penetrating radar (GPR), we investigated an array of shear-deformation bands that developed in unconsolidated Pleistocene glacifluvial Gilbert-type delta sediments. A dense grid (spacing 0.6 m) of GPR profiles was measured on top of a 20 m-long outcrop that exposes shear-deformation bands. Features in the radargrams could be directly tied to the exposure. The shear-deformation bands are partly represented by inclined reflectors and partly by the offset of reflections at delta clinoforms. 3-D interpretation of the 2-D radar sections shows that the bands have near-planar geometries that can be traced throughout the entire sediment volume. Thin sections of sediment samples show that the analysed shear-deformation bands have a denser grain packing than the host sediment. Thus they have a lower porosity and smaller pore sizes and therefore, in the vadose zone, the deformation bands have a higher water content due to enhanced capillary forces. This, together with the partially-developed weak calcite cementation and the distinct offset along the bands, are likely the main reasons for the clear and unambiguous expression of the shear-deformation bands in the radar survey. The study shows that deformation-band arrays can clearly be detected using GPR and quickly mapped over larger sediment volumes. With the 3-D analysis, it is further possible to derive the orientation and geometry of the bands. This allows correlation of the bands with the regional fault trend. Studying deformation bands in unconsolidated sediments with GPR is therefore a powerful approach in paleoseismological studies. Based on our data, we postulate that the outcrop is part of a dextral strike-slip zone that was reactivated by glacial isostatic adjustment.
- ItemUnravelling the shape and stratigraphy of a glacially-overdeepened valley with reflection seismic: the Lienz Basin (Austria)(Basel : Birkhäuser, 2019) Burschil, Thomas; Tanner, David C.; Reitner, Jürgen M.; Buness, Hermann; Gabriel, GeraldWe reveal the subsurface bedrock topography and sedimentary succession of one of the deepest glacially-formed basins in the Eastern Alps: the Lienz Basin in the Upper Drau Valley (Tyrol), by means of seismic reflection. A dense source-receiver spacing, supplied by autonomous receivers, and a prestack depth-migration processing scheme were essential to distinguish the various deposits in fine detail, such as slumping, fan delta deposits, and a modified monocline on the basin flank. These details support our interpretation of the seismic stratigraphy that consists of, e.g., subglacial till of last glacial maximum (LGM) age and possibly older, laminated basin fines, and gravel/coarse sand. The maximum depth of the basin is 622 m, at the junction of two major basement faults that are not clearly visible in the seismic reflections. We regard the overdeepening in this longitudinal valley as the result of glacier confluence during the LGM. Subglacial meltwaters utilized the higher erodibility of faulted rocks, as indicated by channel structures. The adverse slope (2.6%) along the valley axis exceeds the gradient ice-surface slope (0.4–0.5%) during the LGM by more than fivefold. We thus suggest this feature is a product of a pre-LGM phase, since adverse slopes greater than ~ 1.2 times the ice surface slope promote the freezing of water in subglacial channels and prevent efficient water flushing of sediments. Integrating other studies allows us to estimate the local overdeepening of the Lienz Basin and that of the whole Upper Drau Valley to be 146 m and 530 m, respectively. At the beginning of lacustrine sedimentation, we estimate the paleo-water depth to be at least 216 m.