2015, Silina, Yuliya E., Fink-Straube, Claudia, Hayen, Heiko, Volmer, Dietrich A.

In this study, we propose a simple and rapid technique for characterization of free fatty acids and triacylglycerides (TAG) based on palladium nanoparticular (Pd-NP) surface-assisted laser desorption/ionization (SALDI) mass spectrometry (MS). The implemented Pd-NP material allowed detection of free fatty acids and TAGs exclusively as [M + K]+ ions in positive ion mode. Under negative ionization conditions, unusual trimetric structures were generated for free fatty acids, while TAGs underwent irreproducible degradation reactions. Importantly, the mass spectra obtained from Pd-NP targets in positive ion mode were very clean without interferences from matrix-derived ions in the low m/z range and readily enabled the detection of intact TAGs in vegetable oils without major fragmentation reactions as compared to conventional MALDI-MS, requiring only a minimal amount of sample preparation.

2015, Maurer, Johannes H.M., González-García, Lola, Reiser, Beate, Kanelidis, Ioannis, Kraus, Tobias

Ultrathin gold nanowires (AuNWs) with diameters below 2 nm and high aspect ratios are considered to be a promising base material for transparent electrodes. To achieve the conductivity expected for this system, oleylamine must be removed. Herein we present the first study on the conductivity, optical transmission, stability, and structure of AuNW networks before and after sintering with different techniques. Freshly prepared layers consisting of densely packed AuNW bundles were insulating and unstable, decomposing into gold spheres after a few days. Plasma treatments increased the conductivity and stability, coarsened the structure, and left the optical transmission virtually unchanged. Optimal conditions reduced sheet resistances to 50 Ω/sq.

2011, Veith, Michael, Bender, Michael, Lehnert, Tobias, Zimmer, Michael, Jakob, Anette

Lead titanate, lead zirconate, and lead zirconate titanate (PZT) films in the sub-μm-range were produced at temperatures around 400 °C using novel single-source precursors in a classical thermal CVD process. The design of two bimetallic alkoxide compounds, a lead titanate and a lead zirconate source with almost identical physical properties and complement miscibility, resulted in a new quasi-single-source PZT precursor, an azeotropic mixture that evaporates at 30 °C and at a pressure of 4 × 10−1 mbar. After thermal treatment at 650 °C, transparent (100)-oriented PZT films with remnant polarization of 20 μC cm−2 and a coercive field strength of 20 V μm−1 were achieved. An additional lead source is not required.

2016, Reiser, B., González-García, L., Kanelidis, I., Maurer, J.H.M., Kraus, T.

Metal-based nanoparticle inks for printed electronics usually require sintering to improve the poor electron transport at particle-particle interfaces. The ligands required for colloidal stability act as insulating barriers and must be removed in a post-deposition sintering step. This complicates the fabrication process and makes it incompatible with many flexible substrates. Here, we bind a conjugated, electrically conductive polymer on gold nanorods (AuNRs) as a ligand. The polymer, poly[2-(3-thienyl)-ethyloxy-4-butylsulfonate] (PTEBS), provides colloidal stability and good electron transport properties to stable, sintering-free inks. We confirm that the polymer binds strongly through a multidentate binding motif and provides superior colloidal stability in polar solvents over months by IR and Raman spectrometry and zeta potential measurements. We demonstrate that the developed ligand exchange protocol is directly applicable to other polythiophenes such as poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS). Films of AuNRs coated with above polymers reached conductivities directly after deposition comparable to conventional metal inks after ligand removal and retained their conductivity for at least one year when stored under ambient conditions.

2011, Veith, Michael, Belot, Celine, Huch, Volker

In the mononuclear title compound, [Tb(C13H9OS3)3(C4H8O)3]·C4H8O, the lanthanide cation is located on a threefold rotation axis and is surrounded by electron-rich ligands in an approximately octahedral geometry. One of the thienyl groups and the bound THF are disordered with 0.5:0.5 occupancy. The free THF is disordered around the threefold axis.

2016, Fleischmann, Simon, Jäckel, Nicolas, Zeiger, Marco, Krüner, Benjamin, Grobelsek, Ingrid, Formanek, Petr, Choudhury, Soumyadip, Weingarth, Daniel, Presser, Volker

Atomic layer deposition (ALD) is a facile process to decorate carbon surfaces with redox-active nanolayers. This is a particularly attractive route to obtain hybrid electrode materials for high performance electrochemical energy storage applications. Using activated carbon and carbon onions as representatives of substrate materials with large internal or external surface area, respectively, we have studied the enhanced energy storage capacity of vanadium oxide coatings. While the internal porosity of activated carbon readily becomes blocked by obstructing nanopores, carbon onions enable the continued deposition of vanadia within their large interparticle voids. Electrochemical benchmarking in lithium perchlorate in acetonitrile (1 M LiClO4) showed a maximum capacity of 122 mAh/g when using vanadia coated activated carbon and 129 mAh/g for vanadia coated carbon onions. There is an optimum amount of vanadia between 50 and 65 wt % for both substrates that results in an ideal balance between redox-activity and electrical conductivity of the hybrid electrode. Assembling asymmetric (charge balanced) full-cells, a maximum specific energy of 38 Wh/kg and 29 Wh/kg was found for carbon onions and activated carbon, respectively. The stability of both systems is promising, with a capacity retention of ∼85–91% after 7000 cycles for full-cell measurements.

2012, Presser, Volker, Vakifahmetoglu, Cekdar

This Letter is in response to a recent paper by Ma et al. (CrystEngComm, 2010, 12, 750-754) which arguably studied vanadium carbide nanostructures whereas all available evidence indicates the study of vanadium oxide. We feel that it is important to communicate to the community several inconsistencies so that the interesting material reported can be seen in the right light, especially with several groups nowadays having reported similar structures from vanadium oxide synthesis.

2014, Presser, Volker

Electrical energy storage (EES) is one of the most critical areas of technological research around the world. Storing and efficiently using electricity generated by intermittent sources and the transition of our transportation fleet to electric drive depend fundamentally on the development of EES systems with high energy and power densities. Supercapacitors are promising devices for highly efficient energy storage and power management, yet they still suffer from moderate energy densities compared to batteries. To establish a detailed understanding of the science and technology of carbon/carbon supercapacitors, this review discusses the basic principles of the electrical double-layer (EDL), especially regarding the correlation between ion size/ion solvation and the pore size of porous carbon electrodes. We summarize the key aspects of various carbon materials synthesized for use in supercapacitors. With the objective of improving the energy density, the last two sections are dedicated to strategies to increase the capacitance by either introducing pseudocapacitive materials or by using novel electrolytes that allow to increasing the cell voltage. In particular, advances in ionic liquids, but also in the field of organic electrolytes, are discussed and electrode mass balancing is expanded because of its importance to create higher performance asymmetric electrochemical capacitors.

2011, Veith, Michael, Bubel, Carsten, Zimmer, Michael

A new type of precursor has been developed by molecular design and synthesised to produce tin doped indium oxide (ITO). The precursor consists of a newly developed bimetallic indium tin alkoxide, Me2In(OtBu)3Sn (Me = CH3, OtBu = OC(CH3)3), which is in equilibrium with an excess of Me2In(OtBu). This quasi single-source precursor is applied in a sol–gel process to produce powders and coatings of ITO using a one-step heat treatment process under an inert atmosphere. The main advantage of this system is the simple heat treatment that leads to the disproportionation of the bivalent Sn(II) precursor into Sn(IV) and metallic tin, resulting in an overall reduced state of the metal in the final tin doped indium oxide (ITO) material, hence avoiding the usually necessary reduction step. Solid state 119Sn-NMR measurements of powder samples confirm the appearance of Sn(II) in an amorphous gel state and of metallic tin after annealing under nitrogen. The corresponding preparation of ITO coatings by spin coating on glass leads to transparent conductive layers with a high transmittance of visible light and a low electrical resistivity without the necessity of a reduction step.

2015, Blass, Johanna, Bozna, Bianca, Albrecht, Marcel, Krings, Jennifer A., Ravoo, Bart Jan, Wenz, Gerhard, Bennewitz, Roland

Friction and adhesion between two β-cyclodextrin functionalized surfaces can be switched reversibly by external light stimuli. The interaction between the cyclodextrin molecules attached to the tip of an atomic force microscope and a silicon wafer surface is mediated by complexation of ditopic azobenzene guest molecules. At the single molecule level, the rupture force of an individual complex is 61 ± 10 pN.