73 results
Search Results
Now showing 1 - 10 of 73
- ItemThermal annealing to influence the vapor sensing behavior of co-continuous poly(lactic acid)/polystyrene/multiwalled carbon nanotube composites(Amsterdam [u.a.] : Elsevier Science, 2020) Li, Yilong; Pionteck, Jürgen; Pötschke, Petra; Voit, BrigitteWith the main purpose of being used as vapor leakage detector, the volatile organic compound (VOC) vapor sensing properties of conductive polymer blend composites were studied. Poly(lactic acid)/polystyrene/multi-walled carbon nanotube (PLA/PS/MWCNT) based conductive polymer composites (CPCs) in which the polymer components exhibit different interactions with the vapors, were prepared by melt mixing. CPCs with a blend composition of 50/50 wt% resulted in the finest co-continuous structure and selective MWCNT localization in PLA. Therefore, these composites were selected for sensor tests. Thermal annealing was applied aiming to maintain the blend structure but improving the sensing reversibility of CPC sensors towards high vapor concentrations. Different sensing protocols were applied using acetone (good solvent for PS and PLA) and cyclohexane (good solvent for PS but poor solvent for PLA) vapors. Increasing acetone vapor concentration resulted in increased relative resistance change (Rrel) of CPCs. Saturated cyclohexane vapor resulted in lower response than nearly saturated acetone vapor. The thermal annealing at 150 °C did not change the blend morphology but increased the PLA crystallinity, making the CPC sensors more resistant to vapor stimulation, resulting in lower Rrel but better reversibility after vapor exposure.
- ItemTemperature-dependent dynamic compressive properties and failure mechanisms of the additively manufactured CoCrFeMnNi high entropy alloy(Oxford : Elsevier Science, 2022) Chen, Hongyu; Liu, Yang; Wang, Yonggang; Li, Zhiguo; Wang, Di; Kosiba, KonradCoCrFeMnNi high entropy alloy (HEA) parts were fabricated by laser powder bed fusion (LPBF), and their dynamic compressive properties at different temperatures as well as the resulting microstructures were analyzed. The HEAs showed an unprecedented strength-ductility combination, especially at a cryogenic temperature of 77 K and a high strain rate of 3000 s−1. Under this testing condition, the yield strength (YS) of the HEAs amounted to 665 MPa. Regardless of the testing temperature, the deformation mechanism of all investigated HEAs was dominated by a synergistic effect consisting of deformation twinning and dislocation pile-up around twins. The fraction of twin boundaries and dislocation density within the deformed microstructure of the HEA correlated with the test temperature. At 77 K, the formation of nanotwins together with dislocation slip prevailed and contributed to pronounced twin-twin and twin-dislocation interactions which effectively restricted the dislocation movement and, hence, contributed to a higher YS as well as strain hardening rate in comparison to that of the HEAs at room temperature of 298 K. The LPBF-fabricated HEAs showed unpronounced thermal softening even at a high testing temperature of 1073 K. Continuous dynamic recrystallization was restricted in the HEA because of its inherent sluggish dislocation kinetics and low stacking fault energy.
- ItemTransparent model concrete with tunable rheology for investigating flow and particle-migration during transport in pipes(Amsterdam [u.a.] : Elsevier Science, 2020) Auernhammer, Günter K.; Fataei, Shirin; Haustein, Martin A.; Patel, Himanshu P.; Schwarze, Rüdiger; Secrieru, Egor; Mechtcherine, ViktorThe article describes the adaption and properties of a model concrete for detailed flow studies. To adapt the yield stress and plastic viscosity of the model concrete to the corresponding rheological properties of real concrete, the model concrete is made of a mixture of glass beads and a non-Newtonian fluid. The refractive index of the non-Newtonian fluid is adjusted to the refractive index of the glass beads by the addition of a further constituent. The rheological properties of the model concrete are characterised by measurements in concrete rheometers. Finally, the first exemplary results from experiments with the model concrete are presented, which give incipient impressions of the complex internal dynamics in flowing concrete.
- ItemControlling the Young’s modulus of a ß-type Ti-Nb alloy via strong texturing by LPBF(Amsterdam [u.a.] : Elsevier Science, 2022) Pilz, Stefan; Gustmann, Tobias; Günther, Fabian; Zimmermann, Martina; Kühn, Uta; Gebert, AnnettThe ß-type Ti-42Nb alloy was processed by laser powder bed fusion (LPBF) with an infrared top hat laser configuration aiming to control the Young’s modulus by creating an adapted crystallographic texture. Utilizing a top hat laser, a microstructure with a strong 〈0 0 1〉 texture parallel to the building direction and highly elongated grains was generated. This microstructure results in a strong anisotropy of the Young’s modulus that was modeled based on the single crystal elastic tensor and the experimental texture data. Tensile tests along selected loading directions were conducted to study the mechanical anisotropy and showed a good correlation with the modeled data. A Young’s modulus as low as 44 GPa was measured parallel to the building direction, which corresponds to a significant reduction of over 30% compared to the Young’s modulus of the Gaussian reference samples (67–69 GPa). At the same time a high 0.2% yield strength of 674 MPa was retained. The results reveal the high potential of LPBF processing utilizing a top hat laser configuration to fabricate patient-specific implants with an adapted low Young’s modulus along the main loading direction and a tailored mechanical biofunctionality.
- ItemDesigning the microstructural constituents of an additively manufactured near β Ti alloy for an enhanced mechanical and corrosion response(Amsterdam [u.a.] : Elsevier Science, 2022) Hariharan, Avinash; Goldberg, Phil; Gustmann, Tobias; Maawad, Emad; Pilz, Stefan; Schell, Frederic; Kunze, Tim; Zwahr, Christoph; Gebert, AnnettAdditive manufacturing of near β-type Ti-13Nb-13Zr alloys using the laser powder bed fusion process (LPBF) opens up new avenues to tailor the microstructure and subsequent macro-scale properties that aids in developing new generation patient-specific, load-bearing orthopedic implants. In this work, we investigate a wide range of LPBF parameter space to optimize the volumetric energy density, surface characteristics and melt track widths to achieve a stable process and part density of greater than 99 %. Further, optimized sample states were achieved via thermal post-processing using standard capability aging, super-transus (900 °C) and sub-transus (660 °C) heat treatment strategies with varying quenching mediums (air, water and ice). The applied heat treatment strategies induce various fractions of α, martensite (α', α'') in combination with the β phase and strongly correlated with the observed enhanced mechanical properties and a relatively low elastic modulus. In summary, our work highlights a practical strategy for optimizing the mechanical and corrosion properties of a LPBF produced near β-type Ti-13Nb-13Zr alloy via careful evaluation of processing and post-processing steps and the interrelation to the corresponding microstructures. Corrosion studies revealed excellent corrosion resistances of the heat-treated LPBF samples comparable to wrought Ti-13Nb-13Zr alloys.
- ItemAdditively manufactured AlSi10Mg lattices – Potential and limits of modelling as-designed structures(Amsterdam [u.a.] : Elsevier Science, 2022) Gebhardt, Ulrike; Gustmann, Tobias; Giebeler, Lars; Hirsch, Franz; Hufenbach, Julia Kristin; Kästner, MarkusAdditive manufacturing overcomes the restrictions of classical manufacturing methods and enables the production of near-net-shaped, complex geometries. In that context, lattice structures are of high interest due to their superior weight reduction potential. AlSi10Mg is a well-known alloy for additive manufacturing and well suited for such applications due to its high strength to material density ratio. It has been selected in this study for producing bulk material and complex geometries of a strut-based lattice type (rhombic dodecahedron). A detailed characterisation of as-built and heat-treated specimens has been conducted including microstructural analyses, identification of imperfections and rigorous mechanical testing under different load conditions. An isotropic elastic–plastic material model is deduced on the basis of tension test results of bulk material test specimens. Performed experiments under compression, shear, torsion and tension load are compared to their virtual equivalents. With the help of numerical modelling, the overall structural behaviour was simulated using the detailed lattice geometry and was successfully predicted by the presented numerical models. The discussion of the limits of this approach aims to evaluate the potential of the numerical assessment in the modelling of the properties for novel lightweight structures.
- ItemIntegrating climate change adaptation in coastal governance of the Barcelona metropolitan area(Dordrecht [u.a.] : Springer Science + Business Media B.V, 2021) Sauer, Inga J.; Roca, Elisabet; Villares, MíriamCoastal cities are exposed to high risks due to climate change, as they are potentially affected by both rising sea levels and increasingly intense and frequent coastal storms. Socio-economic drivers also increase exposure to natural hazards, accelerate environmental degradation, and require adaptive governance structures to moderate negative impacts. Here, we use a social network analysis (SNA) combined with further qualitative information to identify barriers and enablers of adaptive governance in the Barcelona metropolitan area. By analyzing how climate change adaptation is mainstreamed between different administrative scales as well as different societal actors, we can determine the governance structures and external conditions that hamper or foster strategical adaptation plans from being used as operational adaptation tools. We identify a diverse set of stakeholders acting at different administrative levels (local to national), in public administration, science, civil society, and the tourism economy. The metropolitan administration acts as an important bridging organization by promoting climate change adaptation to different interest groups and by passing knowledge between actors. Nonetheless, national adaptation planning fails to take into account local experiences in coastal protection, which leads to an ineffective science policy interaction and limits adaptive management and learning opportunities. Overcoming this is difficult, however, as the effectiveness of local adaptation strategies in the Barcelona metropolitan area is very limited due to a strong centralization of power at the national level and a lack of polycentricity. Due to the high touristic pressure, the legal framework is currently oriented to primarily meet the demands of recreational use and tourism, prioritizing these aspects in daily management practice. Therefore, touristic and economic activities need to be aligned to adaptation efforts, to convert them from barriers into drivers for adaptation action. Our work strongly suggests that more effectively embedding adaptation planning and action into existing legal structures of coastal management would allow strategic adaptation plans to be an effective operational tool for local coastal governance.
- ItemStructure-property relationships of imperfect additively manufactured lattices based on triply periodic minimal surfaces(Amsterdam [u.a.] : Elsevier Science, 2022) Günther, Fabian; Hirsch, Franz; Pilz, Stefan; Wagner, Markus; Gebert, Annett; Kästner, Markus; Zimmermann, MartinaLattices based on triply periodic minimal surfaces (TPMS) have recently attracted increasing interest, but their additive manufacturing (AM) is fraught with imperfections that compromise their structural integrity. Initial research has addressed the influence of process-induced imperfections in lattices, but so far numerical work for TPMS lattices is insufficient. Therefore, in the present study, the structure–property relationships of TPMS lattices, including their imperfections, are investigated experimentally and numerically. The main focus is on a biomimetic Schoen I-WP network lattice made of laser powder bed fusion (LPBF) processed Ti-42Nb designed for bone tissue engineering (BTE). The lattice is scanned by computed tomography (CT) and its as-built morphology is examined before a modeling procedure for artificial reconstruction is developed. The structure–property relationships are analyzed by experimental and numerical compression tests. An anisotropic elastoplastic material model is parameterized for finite element analyses (FEA). The numerical results indicates that the reconstruction of the as-built morphology decisively improves the prediction accuracy compared to the ideal design. This work highlights the central importance of process-related imperfections for the structure–property relationships of TPMS lattices and proposes a modeling procedure to capture their implications.
- ItemDirect observation of nanocrystal-induced enhancement of tensile ductility in a metallic glass composite(Amsterdam [u.a.] : Elsevier Science, 2021) Gammer, Christoph; Rentenberger, Christian; Beitelschmidt, Denise; Minor, Andrew M.; Eckert, JürgenBulk metallic glasses (BMGs) have attracted wide interest, but their successful application is hindered by their low ductility at room temperature. Therefore, the use of composites of a BMG matrix with crystalline secondary phases has been proposed to overcome this drawback. In the present work we demonstrate the fabrication of a tailored BMG nanocomposite containing a high density of monodisperse nanocrystals with a size of around 20 nm using a combination of mechanical and thermal treatment of Cu36Zr48Al8Ag8 well below the crystallization temperature. Direct observations of the interaction of the nanocrystals with a shear band during in situ deformation in a transmission electron microscope demonstrate that the achieved nanocomposite has the potential to inhibit catastrophic fracture in tension. This demonstrates that a sufficient number of nanoscale structural heterogeneities can be a route towards BMG composites with superior mechanical properties.
- ItemTwo-photon, visible light water splitting at a molecular ruthenium complex(Cambridge : RSC Publ., 2021) Schneidewind, Jacob; Argüello Cordero, Miguel A.; Junge, Henrik; Lochbrunner, Stefan; Beller, MatthiasWater splitting to give molecular oxygen and hydrogen or the corresponding protons and electrons is a fundamental four-electron redox process, which forms the basis of photosynthesis and is a promising approach to convert solar into chemical energy. Artificial water splitting systems have struggled with orchestrating the kinetically complex absorption of four photons as well as the difficult utilization of visible light. Based on a detailed kinetic, spectroscopic and computational study of Milstein's ruthenium complex, we report a new mechanistic paradigm for water splitting, which requires only two photons and offers a new method to extend the range of usable wavelengths far into the visible region. We show that two-photon water splitting is enabled by absorption of the first, shorter wavelength photon, which produces an intermediate capable of absorbing the second, longer wavelength photon (up to 630 nm). The second absorption then causes O–O bond formation and liberation of O2. Theoretical modelling shows that two-photon water splitting can be used to achieve a maximum solar-to-hydrogen efficiency of 18.8%, which could be increased further to 28.6% through photochemical instead of thermal H2 release. It is therefore possible to exceed the maximum efficiency of dual absorber systems while only requiring a single catalyst. Due to the lower kinetic complexity, intrinsic utilization of a wide wavelength range and high-performance potential, we believe that this mechanism will inspire the development of a new class of water splitting systems that go beyond the reaction blueprint of photosynthesis.