16 results
Search Results
Now showing 1 - 10 of 16
- ItemGas-discharge plasma-assisted functionalization of titanium implant surfaces(Baech : Trans Tech Publications Ltd., 2010) Schröder, Karsten; Finke, Birgit; Polak, Martin; Lüthen, Frank; Nebe, Barbara; Rychly, Joachim; Bader, Rainer; Lukowski, Gerold; Walschus, Uwe; Schlosser, Michael; Ohl, Andreas; Weltmann, Klaus DieterA crucial factor for in-growth of metallic implants in the bone stock is the rapid cellular acceptance whilst prevention of bacterial adhesion on the surface. Such contradictorily adhesion events could be triggered by surface properties. There already exists fundamental knowledge about the influence of physicochemical surface properties like roughness, titanium dioxide modifications, cleanness, and (mainly ceramic) coatings on cell and microbial behavior in vitro and in vivo. The titanium surface can be equipped with antimicrobial properties by plasma-based copper implantation, which allows the release and generation of small concentrations of copper ions during contact with water-based biological liquids. Additionally, the titanium surface was equipped with amino groups by the deposition of an ultrathin plasma polymer. This coating on the one hand does not significantly reduce the generation of copper ions, and on the other hand improves the adhesion and spreading of osteoblast cells. The process development was accompanied by physicochemical surface analyses like XPS, FTIR, contact angle, SEM, and AFM. Very thin modified layers were created, which are resistant to hydrolysis and delamination. These titanium surface functionalizations were found to have either an antimicrobial activity or cell-adhesive properties. Intramuscular implantation of titanium samples coated with the cell-adhesive plasma polymer in rats revealed a reduced inflammation reaction compared to uncoated titanium. © (2010) Trans Tech Publications.
- ItemEmission Spectroscopy During High-Current Anode Modes in Vacuum Arc(Praha : Czech Technical University in Prague, Faculty of Electrical Engineering, Department of Physics, 2017) Khakpour, A.; Methling, R.; Franke, S.; Gortschakow, S.; Uhrlandt, D.A vacuum interrupter reaches its interruption limit once high-current anode phenomena occur. High-current anode modes lead to an increase of the anode surface temperature and an increased generation of metal vapor, which may result in a weakening of the dielectric recovery strength after current zero. In this work, different discharge modes in a vacuum arc for AC 50 Hz including diffuse, footpoint, anode spot type 1 and type 2, and anode plume are investigated. Electrodes made of CuCr7525 with diameter of 10 mm are used. The final gap length is about 20 mm. Time and space resolved optical emission spectroscopy is used to examine the temporal and spatial distribution of atomic and ionic copper lines. The distribution of atomic and ionic lines parallel and perpendicular to the anode surface is investigated. Radiator density is also determined for CuI, CuII, and CuIII near the anode surface.
- ItemComparative studies of low-intensity short-length arcs(Praha : Czech Technical University in Prague, Faculty of Electrical Engineering, Department of Physics, 2019) Baeva, M.; Siewert, E.; Uhrlandt, D.We present results obtained by two non-equilibrium modelling approaches and experiments on low-intensity short-length arcs in argon at atmospheric pressure. The first one considers a quasi-neutral arc column combined with boundary conditions on the electrodes based on the energy balance in the space-charge sheaths. The second approach applies a unified description over the entire gap and solves the Poisson equation for the self-consistent electric field. The experiments provide the arc voltage.
- ItemAnalysis of C2 SWAN bands in ablation-dominated arcs in CO2 atmosphere(Praha : Czech Technical University in Prague, Faculty of Electrical Engineering, Department of Physics, 2019) Methling, R.; Franke, St.; Götte, N.; Wetzeler, S.; Uhrlandt, D.A model circuit breaker in a high-pressure chamber filled with CO2 atmosphere is used to operate a wall-stabilized arc of several kilo-amperes between tungsten-copper electrodes surrounded by polytetrafluoroethylene nozzles. Optical emission spectroscopy (OES) is carried out via quartz plates inserted into the nozzles using a combination of an imaging spectrometer either with a high-speed video camera or with an ICCD camera. Depending on the nozzle geometry and the current, continuum from C2 Swan bands was detected as absorption as well as emission pattern. After current zero, optical absorption spectroscopy (OAS) using a xenon flashlamp as broadband background radiator was applied. An absorption around 493 nm was detected and attributed to CuF molecules. The study proofs the existence of C2 in the active phase and the formation of CuF near to current zero.
- ItemAnalysis of erosion resistance of CuC arcing contacts manufactured by plasma spraying technology(Praha : Czech Technical University in Prague, Faculty of Electrical Engineering, Department of Physics, 2019) Derevyankin, P.; Frolov, V.; Gonzalez, D.; Gortschakow, S.; Methling, R.; Uhrlandt, D.Results of the erosion resistance study of the CuC electrodes manufactured by plasma spraying technology are presented. The diagnostics has have been performed by means of high-speed camera technique and optical emission spectroscopy which has been synchronised with electrical diagnostics. After the load material analyses, namely determination of mass loss and analysis of micro sections, have been done. It has been found that the erosion rate depends on conditions applied for the formation of coating layer, which was deposited either in air or in argon plasma. Furthermore, the erosion rate is significantly lower in the case of air plasma spraying.
- Item3D analysis of low-voltage gas-filled DC switch using simplified arc model(Praha : Czech Technical University in Prague, Faculty of Electrical Engineering, Department of Physics, 2019) Gortschakow, S.; Gonzalez, D.; Yu, S.; Werner, F.Electro-magnetic simulations have been used for the visualization of distribution of Lorentz force acting on a DC switching arc in low-voltage contactor. A simplified plasma model (black-box model) was applied for the description of arc conductivity. Arc geometry was gained from the high-speed camera images. Influence of arc position, arc current and of external magnetic field has been studied. Results have been compared with optical observations of the arc dynamics.
- ItemAdvanced Nonequilibrium Modelling of DC Tungsten-Inert Gas Arcs(Praha : Czech Technical University in Prague, Faculty of Electrical Engineering, Department of Physics, 2017) Baeva, M.; Uhrlandt, D.The paper is concerned with the state-of-the-art nonequilibrium modelling of a DC tungsten-inert gas arc plasma. The advanced description involves the two-way interaction between the plasma and the electrodes. Results in atmospheric pressure argon demonstrating important features of the arc plasma are presented and discussed. First results in the presence of metal vapour released from the molten anode are presented. Outlook for further developments in nonequilibrium arc modelling are discussed.
- ItemInfluence of resonance radiation transport on chemical equilibrium in an argon arc(Praha : Czech Technical University in Prague, Faculty of Electrical Engineering, Department of Physics, 2019) Gortschakow, S.; Kalanov, D.; Golubovskii, Yu.Deviations from chemical equilibrium in argon arc plasma are analysed by means of collisional-radiative model. Corresponding comprehensive kinetic scheme has been developed and applied form study of free-burning arc at the conditions typical for welding applications. While the natural lifetime have been used for radiation emitted from highly excited argon states, the resonance radiation was described taking into account the radiation transport effects. Resulting spatial distributions of excited argon atoms are compared for the cases of LTE and two-temperature plasma using different approaches for the description of the resonance radiation transport.
- ItemAdvanced Approach for Radiation Transport Description in 3D Collisional-radiative Models(Praha : Czech Technical University in Prague, Faculty of Electrical Engineering, Department of Physics, 2017) Kalanov, D.; Golubovskii, Y.B.; Uhrlandt, D.; Gortschakow, S.The description of radiation transport phenomena in the frames of collisional-radiative models requires the solution of Holstein-Biberman equation. An advanced solutuion method for 3D plasma obejcts is proposed. The method is applicable for various line contours in a wide range of absorption coefficients. Developed approach is based on discretization of the arbitrary plasma volume on a Cartesian voxel grid. Transport of photons between the cells is computed using the ray traversal algorithm by Amanatides [1]. Solution of the particle balance equations with computed in advance radiative transfer matrix is demonstrated for various typical arc shapes, like e.g. free-burning arc and cylindric arc. Results are compared with corresponding calculations using previously developed approaches. As the method is suited for finite geometries and allows for a strict solution of the radiation transport equation, applicability ranges of previous approximations can be specified.
- ItemSignificance of the Resonance Condition for Controlling the Seam Position in Laser-assisted TIG Welding(Amsterdam [u.a.] : Elsevier, 2016) Emde, B.; Huse, M.; Hermsdorf, J.; Kaierle, S.; Wesling, V.; Overmeyer, L.; Kozakov, R.; Uhrlandt, D.As an energy-preserving variant of laser hybrid welding, laser-assisted arc welding uses laser powers of less than 1 kW. Recent studies have shown that the electrical conductivity of a TIG welding arc changes within the arc in case of a resonant interaction between laser radiation and argon atoms. This paper presents investigations on how to control the position of the arc root on the workpiece by means of the resonant interaction. Furthermore, the influence on the welding result is demonstrated. The welding tests were carried out on a cooled copper plate and steel samples with resonant and non-resonant laser radiation. Moreover, an analysis of the weld seam is presented.