6 results
Search Results
Now showing 1 - 6 of 6
- ItemMicrostructure and elastic deformation behavior of β-type Ti-29Nb-13Ta-4.6Zr with promising mechanical properties for stent applications(Amsterdam : Elsevier B.V., 2019) Plaine, A.H.; Silva, M.R.D.; Bolfarini, C.In this paper, an attempt was made to combine theoretical composition design and thermo-mechanical treatments to produce a metastable β-type titanium alloy with mechanical compatibility for self-expandable stent applications. Metastable β-type Ti-29Nb-13Ta-4.6â»Zr (wt.%) thin-wires with an elastic modulus of 46â»GPa and a yield strength of 920â»MPa were successfully fabricated by cold rolling and low temperature aging. This combination of high yield strength and comparatively low elastic modulus resulted in enhanced elastic recoverable strain of 1.9%, which is much higher than that of the conventional metallic stent materials. The microstructure responsible for the much sought-after mechanical properties was observed to be mainly consisted of a homogeneous distribution of nanometer-sized α-precipitates in a β-phase matrix obtained via a spinodal decomposition of the pre-existed α″-martensite phase through α″â»→â»α″ leanâ»+â»α″ richâ»→â»αâ»+â»β. The α-precipitates increase the strength of the material by hindering the motion of dislocations (spinodal hardening) while the β-matrix with relatively low content of β-stabilizers gives rise to the observed low elastic modulus. More broadly, these findings could be extended to developing advanced metastable β-type titanium alloys for implant and other engineering applications.
- ItemEfficient suboxide sources in oxide molecular beam epitaxy using mixed metal + oxide charges: The examples of SnO and Ga2O(Melville, NY : AIP Publ., 2020) Hoffmann, Georg; Budde, Melanie; Mazzolini, Piero; Bierwagend, OliverSources of suboxides, providing several advantages over metal sources for the molecular beam epitaxy (MBE) of oxides, are conventionally realized by decomposing the corresponding oxide charge at extreme temperatures. By quadrupole mass spectrometry of the direct flux from an effusion cell, we compare this conventional approach to the reaction of a mixed oxide + metal charge as a source for suboxides with the examples of SnO2 + Sn → 2 SnO and Ga2O3 + 4 Ga → 3 Ga2O. The high decomposition temperatures of the pure oxide charge were found to produce a high parasitic oxygen background. In contrast, the mixed charges reacted at significantly lower temperatures, providing high suboxide fluxes without additional parasitic oxygen. For the SnO source, we found a significant fraction of Sn2O2 in the flux from the mixed charge that was basically absent in the flux from the pure oxide charge. We demonstrate the plasma-assisted MBE growth of SnO2 using the mixed Sn + SnO2 charge to require less activated oxygen and a significantly lower source temperature than the corresponding growth from a pure Sn charge. Thus, the sublimation of mixed metal + oxide charges provides an efficient suboxide source for the growth of oxides by MBE. Thermodynamic calculations predict this advantage for further oxides as well, e.g., SiO2, GeO2, Al2O3, In2O3, La2O3, and Pr2O3 © 2020 Author(s).
- ItemElectrodeposition of nanocrystalline Fe-P coatings: Influence of bath temperature and glycine concentration on structure, mechanical and corrosion behavior(Basel : MDPI AG, 2019) Kovalska, N.; Tsyntsaru, N.; Cesiulis, H.; Gebert, A.; Fornell, J.; Pellicer, E.; Sort, J.; Hansal, W.; Kautek, W.A detailed electrochemical study and investigation of a Fe-P glycine bath as a function of the temperature and glycine concentrations and current density, and their resulting corrosion and mechanical behavior is presented. A low addition of glycine to the electrolyte led to a drastic increase of the P content. At low Fe-P deposition rates, heterogeneous rough deposits with morphological bumps and pores were observed. By increasing the Fe-P deposition rate, the number of pores were reduced drastically, resulting in smooth coatings. Increasing the P content led to the formation of nanocrystalline grains from an "amorphous-like" state. Coatings with higher P contents exhibited better corrosion resistance and hardening, most likely attributed to grain boundary strengthening.
- ItemSpectroscopy of solid-solution transparent sesquioxide laser ceramic Tm:LuYO3(Washington, DC : OSA, 2022) Eremeev, Kirill; Loiko, Pavel; Braud, Alain; Camy, Patrice; Zhang, Jian; Xu, Xiaodong; Zhao, Yongguang; Liu, Peng; Balabanov, Stanislav; Dunina, Elena; Kornienko, Alexey; Fomicheva, Liudmila; Mateos, Xavier; Griebner, Uwe; Petrov, Valentin; Wang, Li; Chen, WeidongWe report on a detailed spectroscopic study of a Tm3+-doped transparent sesquioxide ceramic based on a solid-solution (lutetia – yttria, LuYO3) composition. The ceramic was fabricated using commercial oxide powders by hot isostatic pressing at 1600°C for 3 h at 190 MPa argon pressure. The most intense Raman peak in Tm:LuYO3 at 385.4 cm−1 takes an intermediate position between those for the parent compounds and is notably broadened (linewidth: 12.8 cm−1). The transition intensities of Tm3+ ions were calculated using the Judd-Ofelt theory; the intensity parameters are W2 = 2.537, W4 = 1.156 and W6 = 0.939 [1020 cm2]. For the 3F4 → 3H6 transition, the stimulated-emission cross-section amounts to 0.27 × 10−20 cm2 at 2059nm and the reabsorption-free luminescence lifetime is 3.47 ms (the 3F4 radiative lifetime is 3.85 ± 0.1 ms). The Tm3+ ions in the ceramic exhibit long-wave multiphonon-assisted emission extending up to at least 2.35 µm; a phonon sideband at 2.23 µm is observed and explained by coupling between electronic transitions and the dominant Raman mode of the sesquioxides. Low temperature (12 K) spectroscopy reveals a significant inhomogeneous spectral broadening confirming formation of a substitutional solid-solution. The mixed ceramic is promising for ultrashort pulse generation at >2 µm.
- ItemTransition to the quantum hall regime in InAs nanowire cross-junctions(Bristol : IOP Publ., 2019) Gooth, Johannes; Borg, Mattias; Schmid, Heinz; Bologna, Nicolas; Rossell, Marta D.; Wirths, Stephan; Moselund, Kirsten; Nielsch, Kornelius; Riel, HeikeWe present a low-temperature electrical transport study on four-terminal ballistic InAs nanowire cross-junctions in magnetic fields aligned perpendicular to the cross-plane. Two-terminal longitudinal conductance measurements between opposing contact terminals reveal typical 1D conductance quantization at zero magnetic field. As the magnetic field is applied, the 1D bands evolve into hybrid magneto-electric sub-levels that eventually transform into Landau levels for the widest nanowire devices investigated (width = 100 nm). Hall measurements in a four-terminal configuration on these devices show plateaus in the transverse Hall resistance at high magnetic fields that scale with (ve 2 /h) -1 . e is the elementary charge, h denotes Planck's constant and v is an integer that coincides with the Landau level index determined from the longitudinal conductance measurements. While the 1D conductance quantization in zero magnetic field is fragile against disorder at the NW surface, the plateaus in the Hall resistance at high fields remain robust as expected for a topologically protected Quantum Hall phase. © 2019 IOP Publishing Ltd.
- ItemCathode fall voltage of TIG arcs from a non-equilibrium arc model(Heidelberg : Springer, 2014) Uhrlandt, D.; Baeva, M.; Pipa, A.V.; Kozakov, R.; Gött, G.This work presents modelling results concerning a tungsten inert gas (TIG) welding arc. The model provides a consistent description of the free burning arc, the arc attachment and the electrodes. Thermal and chemical non-equilibrium is considered in the whole arc area, and a detailed model of the cathode space-charge sheath is included. The mechanisms in the cathode pre-sheath are treated in the framework of a non-equilibrium approach which is based on a two-fluid description of electrons and heavy particles and a simplified plasma chemistry of argon. A consistent determination of the electrode fall voltages and temperature distributions is achieved. The model is applied to arcs in pure argon at currents up to 250 A, whereby welding of a workpiece made of mild steel with a fixed burner is considered. Arc voltages in the range from 12 to 17 V are obtained at 50 at 250 A, respectively. The space-charge sheath voltage is found to be about 7 V and almost independent of the current. The corresponding temperatures of the cathode tip are in the range from 3,000 K to about 3,800 K. The results obtained are in a good agreement with measurements.